2017 Silverado Z71 - Exhaust Mod Upgrade - WOW Such Fail, Did you see it coming???

FixItNick
95 followers
4 Video Views·Dec 9, 2022
Decided to upgrade my exhaust mod to something better, and then i failed by trying to rush things before had to run to work, felt like such a dummy hahaha. If you saw the fail coming before i explained it, let me know in the comments bellow!!!
2017 Silverado Parts List: https://amzn.to/2RCyBqC
My Garage Products: https://amzn.to/2QlHZdO
My Instagram Page: http://instagram.com/fixitnick
My email Contact: [email protected]
Guys what is going on welcome to the channel and today I'm gonna do a little mod to the Silverado.
I have maybe one hour before I have to go to work but I think I can get this done and install
this little clamp right here. We wanted to do this for quite a bit because I did notice that
this clamp in the back was leaking air. So what I'm gonna have to do is remove the tip
and then remove this section right here and remove the other section in the front
and then get this thing welded on there. And also another reason is because this side
seems to be loose even though I tightened the bolts right here. So I'm thinking this is the
stock pipe this is the Flowmaster pipe so one of them is maybe slightly thicker so when it clamps
down it clamps down to one of them tighter than the other one so and it can only go so far over
here. So I'm gonna go ahead and remove the two sections of the exhaust and weld on the clamp.
Worst case scenario if I need to go to work if I'm getting too tight on time I'll just install
the front part and I'll just drive it that way. It's gonna sound the same there's no muffler
there's no resonator so it's gonna it's not gonna make a difference. Alrighty let's go.
So basically how this clamp will work is it will separate in two and this part
I'm gonna weld right here and it sits in there pretty tightly. So I'm gonna tack weld a couple
spots and I'll just go around I'm gonna clean this area up that's why it has this little
groove in there so the pipe can sit inside. These are really good for like turbos and down pipes
but I decided to go ahead and try it on this one and then when I'll get the other pipe pulled on
then the two pipes will clamp together will go into each other because it has a little groove
in here that goes inside of this groove that way it locks it doesn't slide it's airtight
and then the v-clamp clamps it down even tighter. So like I said this is pretty much for
turbos zero leak applications where there's a lot of pressure. I believe it was $15 I'm gonna
correct myself on the video if it's more than $15 but for $15 something like this
beats the other clamp for I believe it was also $15 or something like that.
Now in this video I'm gonna make a huge mistake and I was wondering how many of you will catch it
and then I'll reveal the mistake at the end of the video so don't skip forward just kind
of watch see if you can catch it I'm curious how many will catch it
but I felt pretty stupid at the end so all right we'll talk how stupid I am at the end.
All right guys so I got the flanges welded on both sides it's not the prettiest I was kind of
in a hurry but I'm gonna throw a little bit of paint on there and install it back in the truck
and hopefully we'll get it done in five minutes or ten minutes because we have to go to work.
Let's see what she sounds like with no pipes pretty much it stops right here
we're after the cat and it's a cold start so let's hear what we get cold start no exhaust.
Here's what it sounds like pretty much no exhaust dumped at the cats
pretty legit I should just dump it at the cat and that should be that should be good to go.
So I'm actually pretty surprised that a pipe with no muffler actually
quiets down the exhaust so much but yeah not my cup of tea so I guess I have to install the
exhaust back on all righty let's go. So guys did you catch the mistake all right let's see what
happened shut up all right shut up. So here's my new exhaust tip check it out guys tell me what
you think so yeah this is the the stupid mistake that I made um I didn't put it on fully I just
kind of put it on to make a little funny meme I guess funny video but yeah when I was welding the
the flange I accidentally welded it on the opposite side not really thinking about it
and then when I was about to install it I saw the stupid mistake that I made. All right so just
finished re-welding the flange and hopefully it's on the right side this this time uh it was on this
side now it's on that side so it's a 50 50 right. All right so I cleaned it up a little bit uh now
I'm just going to spray some black on it and we'll go ahead and install it back in the truck.
Let me know if you guys uh got this mistake uh when I was doing it when I was uh welding the
flange on uh but yeah I had to grind it off and re-weld it on the other side and good thing on
this side I have a tip installed so it's not that big of a deal if it's a little uh messy on this
side. All right now let's go back to uh the finished product start it up and see what the
clamp looks like so you guys can compare so guys if you enjoyed this video please hit the like
let me know in the comments what you think about the fail yes I know I failed I know you guys never
failed in your life so it's all right but um took me a little bit to uh fix the problem but
it's all good now hopefully I'll think twice before welding next time so thanks for watching
subscribe if you're new to the channel see ya
