Tavolo in resina epossidica completo Fai da Te

Fai Da Gio
28 followers
45 Video Views·Dec 8, 2022
Good morning guys I'm going to the mountains to see some wooden
boards and have you seen the weather Let's hope we don't get rain
Guys it's raining and we're near Lake Zeo
Guys we meet again in Vienna he's Roberto
hello Roberto Hello
We came to see some wooden planks look at all the stuff he has here
We also have the tractor so we can go out for a ride
Where there are large roots what size do you use Does it work Roberto In
what way does it work
How do you use it to cut these large roots
Put the trunk under and then through
this Lower Raise
Lower and accelerate
Here and there choose the thickness to cut Then you put
it there and proceed along the tracks and the blade cuts it
The stars shine on the blade
These are roots
Alright guys we've chosen this root and this table to do the wor
Hello everyone and welcome back to the channel
In today's video I want to show you some steps to follow when we need to create process some objects and then resin them
In this video I'm using an olive wood board but you can use any wood as long as it has some cracks to insert the resin
And since you can't directly insert the resin as the table is there are some steps you need to follow in order to be able to resin it
And in this video we will see what they are
If you're new this channel is dedicated to DIY and also some small reviews
So if you haven't subscribed yet subscribe and turn on notifications
In this way I let you know when I post a new video
Let's go
So guys the table I don't know if you can see the cuts
It was cut with a mobile sawmill that big
and not knowing whether it is straight or not
Now the next step will be to bring it to the correct thickness
So I'll have to take it to the carpenter's shop where I put it in the right electric planer
I'll make it all custom-fitted But before taking it I'll have to
clean it so there are these things that need to be cleaned first
Then guys to start cleaning everything that is crumbling
here like this stuff These I 'm using a simple screwdriver
And these tools here which you will surely find in any DIY project
Are you helping out too
You made a hole here you made a hole
Why did you make
a hole here So
Then I'm trying to do as much as
possible in the direction of wood
Then I advise you to try the logs Those
that break it's better to pull them out
Then in that case I see that it moves too much so I pull it away
Once we have cleaned this side we turn it over
This part is less damaged so we will still use
the screwdriver and the tools to clean it Where it can be done
That table here will become a small side
table Those pieces here will be discarded
And the next step will be to plane it and make it all the same thickness
Now the table is planed and beautifully polished
I have reached 4.5 in Era 4.8 thickness
Now guys I'll have to go measure to cut and discard the pieces I don't need
We'll get that piece here
Now boys as the next step we will just have to make some resin and spread it everywhere
In this way all the pores and cracks become blocked and closed
This prevents air from escaping when we make the final pour
So to coat it all in resin I estimated that I would need about 300 grams of resin
Then I made a video where I explain the proportions
In this case I add 200 g of component A
And by calculating the employment ratio I should pay 134 grams of component B
So I need to do this waterproofing on the opposite side as well
I didn't show you how I made the mold because
I've already made one I'll leave the link above
You can safely use the white laminated panel without applying tape
I stuck the tape on this mold because it was a panel
that looked like wood It still had the wood-like traces
So to be safe and prevent it from sticking to the wood I put on the tape
We will need to spray some release agent for greater security
Then guys before putting it in the mold I'll
have to try to seal the bottom part That is these
So that the resin does not come out and then touching me to cut too much
In this way I try to keep it inside
We sealed all the cracks and holes We are
sure that the resin no longer passes through
Then guys I put the two clamps this way
So that the table is properly supported and does not lift up when I pour the res
Now I will make another 200 grams of component A and 134 grams of component B
That will be a total of 334
Then I will pour a layer of resin 3-4 mm thick
And then we will have to wait another 3 days
In this way we will be sure and certain that the resin does not come out and covers all the holes and cracks
And then it blocks them
Why would I immediately start pouring all the quantity
The air bubbles could remain trapped and could escape much later when the resin was perhaps beginning to gel
And then not allowing me to intervene to break them
Then guys before starting the pour we make sure our table is perfectly level
After we will apply a layer of silicone we
will put it around the cracks holes and edges
So that the resin does not get on the wood because it will be harder to sand later
I'm using an acetic silicone a common sealant that you can find anywhere
Then guys this thing here is done because normally when I go to pour the res
I always have to go over the edge a bit because the resin starts to dry after seven days
If I didn't get it right the first time I'll have to do another pour
So to avoid having to do another pour after I did the final pour
I go to exceed the edge so maybe I'll stop on the silicone
lip in such a way that if it retracts it retracts straight
Now I need to pour the resin We have
calculated the amount I need to pour
If you haven't seen the video I'll leave the link in the top right
Go watch it
Anyway I'm using Resin Pro resin
It is a resin for thick layers
I will still leave the link in the description of everything
They have a variety of resins you can work with comfortably
And before starting I urge you all to always use protective equipment
These would be the gloves long clothing protective mask and
goggles Why with that resin here we have to be very careful
So I told you that for the amounts to be poured a calculation needs
to be done I made the video that I will put in the description
How much resin do I need to mix from A and B
I made another video I left it in the description
A full video is available only on this topic So now
I will pour 5 liters and 500 grams of component A
The remaining amount to reach 9 liters and 200 grams of B
Then guys as I was saying for this table that has a length of 84 cm
Nevertheless I made a previous video in which I clearly explained the dimensions of this table
In total I have added almost 9 liters and 185 grams of both component A and component B resin
Mix it well for at least 3 minutes Make sure
there is no unmixed resin left on the edges
In this way all the resin mixes well
together Then I used a piece of plexiglass
So that when pouring the resin bubbles do not form
Bubbles still form
But in this way we avoid most of the bubbles from forming
But guys once we have done our pour we can use
either an open flame but I recommend a heat gun
Let the resin rest for at least 5 minutes
Meanwhile the bubbles rise to the surface
And then with the heat gun go and pop these bubbles
And intervene every half hour because the bubbles rise to the surface
Some bubbles came out the same because of the high temperature it encountered
It created those things here
So guys I needed to clarify two points
Have you seen that he created these kinds of bubbles both on the surface and inside
And I told you that I did the casting in my garage
And my garage is not climate-
controlled That day when I did the pour the temperature
was below 23°C So it was perfect
Probably that day the temperatures rose which probably created
a mass effect and it started to boil a bit
And the second reason I can think of is that he
created these bubbles because of the mixing of A and B
Then I was telling you they need to be calculated a lot and we have to be very precise
I if you have seen the video I did the mixing in the big bowl
I poured the quantities according to the scale marked on the tola
So I didn't go to weigh it on an electronic scale
With an electronic scale
Then I can think that it was the imperfect mixture
I loaded it into the car and took it to some
of my friends who have a woodworking shop
I ran it through the planer
a dozen times both sides
And it came out perfect
Then guys since this corner here doesn't really look good
how it turned out I thought about making the edges rounded
So that it gives the table a round shape
And I would like to remove this corner here
Now I will remove just half a centimeter from the edge
on all four sides and then I
will make the edges rounded
I'll smooth the edges with the P80 because they didn't turn out perfectly
Then guys at this point we just need to
mill the edges and start sanding it properly
Then guys I don't know if
you can see there are these
imperfections that need to be
covered hey why are you copying me
Why are you copying
me Hey
I'm working here
No I am
Okay let's work together Then as I was
saying these little imperfections here
These holes here They need to be covered so I'll put some silicone around them
Sorry I'll put on the resin
For now we'll wait a bit longer
Why these things need to be
resolved Then guys if you liked what
you've seen so far I just want to remind you to like this video
Sign up for the channel if you haven't already
It would really help me grow
And provide you with this kind of content
Then guys I'll do a little bit of resin
I'll make almost 30 grams of A and 18 of B
I will add to these cracks these
holes that formed when I sanded
I'm doing 21 because it seems already
enough And I'll put 12 grams of B guys
This employment report is 100 for 60
Remember to always wear gloves and a mask
Then guys if you liked what you've seen so far
I just want to remind you to give me a like and subscribe to
the channel if you haven't already
It would really help me grow
I will give you this kind of conte
Then with a cutter blade
I'm trying to remove the silicone
But after I realized tha
I can easily remove it even with the sander
I am still using the P80
because I can clean much deeper
And in this way I can also remove the marks that the sander
left behind I still remember for
whom it was new to the channel
I will describe all the video series
That relates to this table
After finishing sanding with the P80
I start sanding with the P120
240
320
360
400500
600800 10002000 3000
E infine
4000 Vado
a scalare
tutte
le carte
I leave nothing behind Also the
edges need to be sanded properly
Then guys if you liked what you've seen so far I just remind
you to like my video
Subscribe to the channel if you haven't already
It would really help me grow
And provide you with this kind of content
When I reach 500 grit
I start wetting with water
And continue sanding while we
Up to P400
I urge you to closely follow the
movement of the cards because
it is important not to leave
behind the signs of the larger card
After sanding even with the last grit
Here I am already sanding with the P4000
You can already see the difference
It is brighter
Even without polishing
You can already see the difference
Then when we finish sanding the last
grain I have the polish ready here
The lucidator
is a wool
pad and a bit of paper
We stir it a bit
We will drip some directly onto the resin
I used parchment paper here
It would have been better to use a cotton
cloth For the wood I am using a hard wax oil
It creates a very nice effect
It really highlights the grain of the olive wood
I am using a cotton cloth
I know it works very well this
way Even if you approach it with oil
on the resin Nothing happens
Because after you take the pad back
Eat it a little more and then polish it some more
So nothing happens
But meanwhile the wood is absorbing that wax oil
It does him a lot of good It
nourishes and protects him as well
I bought the legs on Amazon
I'll leave the link in the description
The assembly was very simple
Once properly aligned we
mark the points
to make our holes and with a wood bit
I have drilled the holes to screw the nuts in
You can add a little oil
to help tighten it better
If you liked the video I would
appreciate it if you could like it
and share it if you think some of
your friends could benefit from it
Leave a comment as well
If you want to share with our community
Your experience regarding this
If you want to see more videos like this in the future
And you haven't done it yet
Subscribe to the channel by clicking
the red button on the right And enable the notification bell
In this way you will be
informed every time a new
video is uploaded to the
channel See you soon guys
