Welcome to the first in a new series of model making "quick tips." In these shorter videos, I can go into a lot more detail about some of my preferred tools, materials, and techniques. In this first one, I give a step-by-step tutorial on one of my favorite methods for modeling pine logs with realistic bark. This technique was essential for builds like my Big Thunder Saloon and the log cabin at Circle D Ranch. It's also a good start for making foreground trees!
Al music courtesy YouTube Audio Library, attribution given where available. "Banjo Short," and "Country Cue 1" courtesy of Audionautix, licensed under a Creative Commons Attribution 4.0 license.https://creativecommons.org/licenses/by/4.0/ Artist: http://audionautix.com/
Hey folks! Dave here with a quick model making tip from Thunder Mesa Studio.
Let's take a look at one of my favorite techniques for modeling pine logs with realistic bark
texture. Let's take a look at some of the tools and materials I'll be using for this project.
First of all we've got a piece of dowel. This is a quarter inch pine dowel. It's about six and a
quarter inches long which in O scale would make it 25 feet. If you're modeling in smaller scales
you might want to use a smaller doweling. Discretion is advised. And then we've got some
toothpicks, wooden toothpicks. These will be used to model the stubs of branches coming out of the
log. These are kind of fancy ones but any toothpicks will do. I've got some sandpaper in 80 and 120
grit. I've got a 16th of an inch drill bit and a power drill. Utility knife which is really one of
the only hand tools used on this project. Some paint brushes. And then I've got a selection of
acrylic paints. These are just inexpensive craft store acrylics in shades of brown.
Some brown oxide, burnt umber, khaki, territorial beige. And then I've got my old favorite unbleached
titanium for the highlights. And of course we've got some rust-oleum dark brown camo paint.
And some Crescent Creek models scale stucco which we'll be using to create the actual bark texture
on our log. Now if you want to model logs that have been sawn on the ends you can skip this next
step. But I want to model a log that was chopped down with an axe. So I'll be using my utility knife
to go around and whittle away the ends to create the look of axe cuts on each end of the log.
Well now I've chucked up the dowel in my power drill and I'm just tapering it from the lower
end to the top end because of course in nature logs are not the same diameter at the top as they
are at the bottom. They taper towards the top. So I'm just using my drill and some 80 grit sandpaper
to add that taper. That's not bad. Fairly subtle but that'll work. Now I've clamped the log to the
edge of my work table here and chucked up a sixteenth of an inch bit in my drill and I'm
just going to add some holes. I'm going to turn it a quarter turn and pretty much in the same place
buried a little bit quarter turn. Now I'm going to take a little yellow glue which I'm sorry I
didn't mention in the uh when I was talking about tools and materials and just shove one of these
this toothpick down in the hole like so and then very close to the trunk. I want to break it off
just cut it off just like that and just keep going around to all of the holes until they're filled.
Now we're going to use our Crescent Creek Models Scale Stucco to apply some bark texture
to the log. You don't have to use Crescent Creek Models Scale Stucco. You can use
just about any good acrylic modeling paste will do the job. Using a semi-stiff brush pushing it
right into it there and now I'm just going to dab it on. Don't worry about going over those branches.
You actually want to do that. We'll bring them back out in a later step all the way out to the
ends. Don't worry about cutting and covering up the ends either because we're going to bring those
back in a later step also. Now I'm modeling a fallen log or a cut log but if you wanted to
model a tree a growing tree you could use these exact same techniques. If I was going to be doing
a logging scene something where I needed a lot of logs like this I would probably set this whole
process up assembly line fashion and do half a dozen or a dozen of them at a time. Now we'll
let that set up and harden for about 15 minutes or so. Now comes a nice even coat of Rust-Oleum
Camouflage Dark Brown. Now with that Dark Brown base coat dry I can start dry brushing on
the acrylics. What I like to do is start from the darkest shade and mix these two together.
Start from the darkest shade and then work my way towards the lighter shades. I like to use a piece
of corrugated cardboard to get most of the paint off before I start doing this. What I'm trying to
do here, the whole point of dry brushing, is to hit just the tops of the texture so that that
darker brown will show through underneath. Once again I'm using sort of a semi-stiff brush for
this which I find a stiff brush is better for dry brushing. Now I can start working my way
towards the lighter colors. You don't have to wait for this paint underneath to dry.
Just go ahead and apply it right over the top. It's kind of slowly rotating the log as I go,
so I make sure I get all sides. Then lastly we go to the highlights. You want to do this
sparingly. This is Unbleached Titanium. Get most of it off of the brush. Now we can leave that alone
and let that paint dry completely for a while. Now I'm going to do one of the the final steps
which is sand the color off of these ends and reveal the natural wood underneath.
Now I'm going to take my sandpaper and sand the paint off the end of these
branches that are sticking out. Reveal the raw wood underneath. One of the last things is I like
to put some scrape marks where the bark has been ripped away. I'm just whittling off some of that
stucco up here. And a final step, just go around with your your dark brown and touch up any places
where the that white stucco is showing through. And there is our finished log. Ready to go on the
layout or diorama. Thanks for watching that quick model making tip and thanks to Thunder Mesa
Studios patrons for making it possible. Don't forget to subscribe if you'd like to see more.
Adios for now.