Tommy's Trade Secrets - How To Tile A Floor

Magical Mirrors
232 followers
14 Video Views·Dec 6, 2022
Hi I'm Andy from Tradesupermarket.com and today I'm going to show you how to tile a bathroom floor.
Now in our mock studio today we've got our our bathroom floor in question we can actually go
out onto timber so we will need to unibond this and I'll show you all the tools and materials
that we need to use to tile this floor in question today. Now our pottery is already
fitted the bath can stay in place you're not too worried about that. Now obviously you know if it's
the first time you're tiling if you have got a friend who's a plumber or you're quite confident
in plumbing yourself it is best to always take your pottery out. Disconnect your hot and cold
supplies for your basin take your pedestal out disconnect your cold supply for your toilet
take your toilet out. Obviously if you can't do this you're going to have to get yourself a set
of pincers and these are the pincers sort of pincers that you'll need. A floor tile is obviously
you know can be thicker than a than a wall tile they're quite hard to notch and it will take you
a lot of time to create the shapes on the pottery. Anyway moving on the tools and materials that
we're going to need for the job in question today we've got ourselves some unibond because we're
going to be tiling onto a wooden floor we've got a little roller and a little roller tray
we've got a brush I've got a spirit level here which I'm going to use as a straight edge
I've got some sponges just for cleaning off afterwards now I've got some notch trowels here
I've got a notch trowel that is probably about a five mil cut out and I've got a 20 mil cut out
now obviously if your floor at home is very uneven you will need the deep notch trowel
we're going to use the five mil notch trowel today because we're going onto a timber floor
now I've also got a mixing trowel I've got some Mappy Keraquik rapid set flexible tile adhesive
because we're going onto a wooden floor we want it to be flexible it is rapid set if you're
for the first time at home then you know I would suggest don't use the rapid set because
obviously the rapid set goes off pretty quickly and if you're doing your cuts by the time you've
done your cuts it's gone off so anyway I would use the ordinary setting but we're going to use
the rapid set today I've also got a squeegee which is for our grout I've got a bag of grey grout
I've got a tile cutter now this is a wet cutter fantastic for doing floor tiles
I'll show you a few cuts with this I mean you can hire one if you're going to you know just going
to be doing some some tiling for the first time you might be best just hiring one or if a friend
has got one then obviously borrow it off of them I've got some tiles we're going to be laying
about eight square meters today these are the tiles that we're going to use and we've got
more in boxes and I'll show you as we go along the fixing process that we're going to use to
fix these to the floor we've got four mil spacers that we're going to put in between the tiles
now we're going to do a lot of cutting with the ruby cutter fantastic bit of kit use these all
the time we've also got two buckets we're going to obviously have a bucket for our sponge for
cleaning off our tiles and then a bucket just to knock our adhesive up so anyway right that's all
the tools and materials that we're going to use today to do to do our job and we move on to the
tiling and we'll show you how to do that okay moving on to the to the to the bit of tiling
we're going to do today obviously you know there's so many different shapes sizes to bathrooms
obviously our bathroom here I'm just going to show you the basics of tiling always best to try and
get your tiles maybe working to the center of your to the center of your toilet and cistern
to your pan or on on your basin and pedestal you know you might have a full tile coming off there
you might have a cut tile coming off of there always best to try and get you know nice cuts
to the edge of each each wall and then as you're working towards your exit door you know you want
a nice cut there you know there's there's so many so many different like I say so many different
size bathrooms so many different scenarios but obviously we're working on this today and I'll
show you the basic principles of of our room that we've got out here today so what I'll do is I'll
measure the width of our our room which is 2840 so I want to say that's about 1420
which gives me my my middle point of my room and then the best thing is just grab yourself a tile
that you're working with put this on the edge of your line and then see what your cuts are
to the right hand side obviously because we've made that the center of the room the cut to the
right hand side will duplicate that to the cut to the left hand wall so what we do is just mark that off
that's one that's two that's three that's four and as you can see from our finish point there we've
got a nice cut cut to that wall there and that will obviously give us the same cut the other end
regarding the bath what we want to do once we've squared everything up you know 99% of the times
the rooms are not square but if you've got a nice square room then what we want to do is either come
with about three quarter of a tile once our bath panel is on we'll have a three quarter of a tile
showing or in fact even a half a tile what you're trying what you want to try and avoid is um
is you know small cuts to walls and exit doors and baths and so on and so forth right okay I know
that I've got the center of my room there so what I want to do is try and get get some uh get some
measurements going so what we do is spring off of this wall here and I know that off that wall I
know that wall's pretty pretty level so I'm happy with that so we measure 14 20 a little bit further
up just so we can run our lines through we measure again 14 20 just put a little arrow on that and a
little arrow on that let's redo that because I've got a few marks on the floor there we go there's
14 20 there all right straight edge spirit level whatever you can find as a straight edge
we've got our got our spirit level that we're working as a straight edge so I run this through
our two lines like so just get that on with a pencil or a marker pen or whatever
just run this through like so and I know that that it's going to be my it's going to be my
starting line where I'm going to spring off from and then like I say if we work to say three quarters
of a tile say 300 off of there we're going to be approximately uh touching the legs so if I just
line that through like so there's so many ways of doing this I always find this is the best way
I know that line straight so what we do we'll get our straight edge again and we just run this off
of our pencil line at a point again with your pencil just mark this off and when you start
laying your tiles if you come off of these lines every time you put your spaces in your tiles are
going to be straight all the way through so right what we're going to do on this on this point here
is actually our starting point so we're going to lay our first tile off of that and we'll run along
our line come this way work into the bath and then as we go along I'll show you the best way to do it
obviously we're working on a on a wooden floor you know we need to use a pva adhesive on this floor
just so it helps it key and it doesn't drain out all the moisture in the adhesive because it will
suck it out so right what we've got we've got a tiny tiny bit of water there we put some pva in
that in that bucket and just pour some of that in like so we'll just give that little just give
that little stir up with that brush now you can put this on with brush you can put it on with a
broom or whatever I've got a little roller tray here I can pour that into the roller tray
but what I tend to do is just knock this up get myself a little tiny roller what you want to do
is do the whole entire area all you do is just pour this onto the surface like so and then just
work this in all the way across like so and what you want to do is you want to carry out
this procedure until the whole bathroom floor is covered with pva let that let that dry and
then bang you're ready to start tiling okay now we've um unibonded our floor we've left that about
half hour 40 minutes or so right next thing is obviously start mixing up our our tile adhesive
so what we do is remember powder adhesive always gives off a fair bit of dust so if you've got a
mask at home always advisable to wear a mask let me just stick my mask on like so like what I want
to do is pour some water into my mixing bucket again I'm like I say I'm using rapid set so I
don't want too much water in there so what we do is get our bag and we slowly pour this in
into our water you don't want this to be too too thick I'll show you the consistency once I've uh
once I've knocked it up always add a bit more powder if you want to
so with our mixing trowel we'll just bring this together with the water now you can get different
different color colored adhesives you can get a white powdered adhesive you can get
obviously this gray gray adhesive we're going to be using gray tiles we're going to be using gray
grout so that's why we're using the dark colored adhesive if you're using white grout at home on
the floor or on the wall or whatever you're doing always best to use a white powder because if you
get any any gray coming through the tile line and you haven't washed it out properly when you come
to grout it you'll actually see it and it's right that's coming together nicely like so
and try and get all the lumps out if you can if you've got a mixing drill at home
then obviously you can do it with that I'm quite happy with using our our trowel here so
that's the sort of consistency you're looking for so I'll show you what to do next we'll just bring
this over now I'm just going to do a few few straight cuts sorry a few lay a few straight
tiles and then obviously as we get through laying more tiles what we do is I'll show you how to cut
with a wet cutter and then obviously how to cut with our ruby cutter so first things first
obviously we know our starting point here we've got our lines on the floor so what we want to do
is just spread some of this adhesive like so good thing about rapid set adhesive is it goes off
pretty quickly what I normally do is just lay a section first of all get three four maybe five
tiles down off of your lines and then once that's gone off then you can start pushing the tiles
against each other they're not you know they're not going to move out of position so what we'll
do we'll do enough to do let's say a bank of bank of six tiles spread this adhesive out
now like I say if your floor's running out you will need your deep you will need to get a deep
notch trowel but our floor's nice and level you can actually level your tiles in but like I say
our floor is is nice and nice and level so I'm just going to go to go to that today right let's
just get my pencil and we just mark this off so I roughly know where where I'm going to be coming
with my bank of six tiles so I'll roughly be coming there so I can wipe just some of that
excess off so it doesn't go off that's what we do like so and then again get your tile
lay it on your point where you've marked it get your lines nice and straight so you're on your
on your you're lying on your back edge of tile and you're on your side side of your tile
and I know I'm bang on my line there now a lot of tilers they use spacers some tilers don't use
spacers it's entirely up to you obviously if you're going to be doing it for the first time
then I'd highly recommend that you use spacers so get a couple of tiles down on your lines
I've got exactly like that and then once you're you're happy with your lines that it's all going
through you want to just get some tile spacers in there now you can lay tile spacers within the
joints and leave them in there on the floor tiles what we normally do is just place these in
that's still on my outside line just bring that across a little bit like so again spread that
apart get another couple of spaces in there and obviously once this adhesive's gone off good thing
about tile spacers is I pull them out I can reuse them so good you know good invention for a bit
of plastic so again lay your tile like so get another one down and if you just get your your
head down to almost the level of the tile you'll see you know if you need to push it down a little
bit as just make sure they're nice and level so again not a job you want to rush really just take
your time so again tile spacer on the top section what you want to do is get it on each corner like
so and then you know you you know you're gonna have a four mil nice four mil joint running all
the way through gives you a nice little bit of time uh the rapid set obviously if you're working
with standard set you won't be able to walk on it straight away so we just pull them over just
make sure you're happy with all your lines like so and then what we do is we will just clean up
our edges because once this stuff goes off you'll have to get yourself hammer and chisel
or hammer and bolster to knock it off that's nice and clean like so and like I say I'd normally leave
that for half an hour 20 minutes half an hour let that go off once that's gone off and you're happy
it's nice and secure pull your tile spacers off start spreading the rest of your bathroom
and then obviously you can then start laying your tiles but what I mean is when your tile goes off
you can actually push that in there and it and you can push against the tile and them tiles don't go
anywhere nice and secure so what you want to do is you want to continue that all the way through
your bathroom and then sometimes we do the cuts as we go all depends the size of the bathroom floor
or we you know lay all the full tiles first and then we go back and doing all the cutting
so obviously once I've laid a few more tiles we can come back I'll show you a few cuts of a wet
tile and then I'll show you a few cuts of the ruby tile cutter right okay now I've laid them
them final tiles that didn't take no longer than 10 minutes really obviously the most important
thing is make sure they're square make sure you're happy with all the joints before your adhesive
goes off and obviously the most time-consuming bit is obviously doing all your cuts you know
maybe around your pottery or your cut to your walls cut to your architraves so what we want
to do is just clean off clean off that line of adhesive like so and then once that's gone off
obviously we just start saying because that line's been clean I know that I'm you know I'm not going
to be having to chop out the adhesive that's gone off you could do it like that or alternatively
once you've cleaned it off if you're not happy that there might be a few bits lying about just
get your sponge run that through just another little tip for you I'm happy as anything that
that's all nice and square on my joints are the same with your straight edge what you could do
is just lay this up against your tiles like so and as you can see every single one of them tiles
is touching along that straight edge okay now we've given our tiles half an hour to set
they've set nice and firm because we've used the rapid set adhesive so what I'll do now is I'll
just pull out all the spaces because we can reuse these we put these in our in our little tub that
we've got then once I've pulled this all these spaces out the tiles then I'll move over the
other side we finish that bit of floor and then I'll show you some cuts okay now we've knocked
more adhesive up we start to start to spread this side so again just work it away from the tiles
exactly the same as the other side really okay again exactly the same procedure lay your tile
now I know that our floor was pretty level like I said earlier in our video clip if you're unsure
that your floor's not too level what you want to do is obviously grab yourself a spirit level
which I'll just get off my bench here and you can you can actually level all your tiles in
put them across the tile push them down and then just get them nice and level I mean that's lovely
and level so also if you find your floor is running out too much you can spread your adhesive
get yourself a tile just clean that up there that's one side then what you want you could do
is just dab the back of your tiles like so what you don't want to do is create any air pockets
and what you could do is just place this on top of the adhesive and slowly work this in
and then you can find yourself find yourself a level you can push it down at one side because
you know the adhesive's under there and then you know that you can get that level
like so but that's not only if your floor is obviously running out so I'll take that tile up
obviously there's too much adhesive on that and then I'll re-press that put that tile to one side
that's just a tip for you to see if your floor is running out again get your tile in
and then we'll start putting our our spacers in great idea spacers because you can always pull
them out of the tile they're not very expensive to buy but you can pull them out of the tile and
obviously you can reuse them okay so what I'll do is I'll just finish this all the way through
once I finish this then we'll come back and I'll show you the cuts to the wall and the cuts to the
underside of the bath well okay I've now laid all my full tiles put my spacers in between
we'll let that go off and then I'll pull my spacers out normally if I was doing a bathroom
floor or a kitchen floor I'll spread my adhesive up to up to the wall that I've got to do my cuts
to and I would do my cuts as I go but on this occasion because I want to show you how to do
cuts properly I've cleaned the adhesive off of the section where my cut's going to go
so I couldn't show you how to do cuts properly now over in the right hand corner and as you can see
I've got one two cuts that go into our into our wall tiles also I've got a bit of an L-shaped
tile going on there so I'll show you how to cut that even with the ruby cutter or with the wet
cutter and then we finish these tiles all the way along and then that's that area complete
right okay so what we want to do is obviously measure our tile now you can do this in a number
of ways you can put your tape on the floor take your measurement from the wall to the tile take
away the thickness of your spacer that you're putting in both against the wall line and against
your tile line or alternatively you can get your tile you can put it up against the wall
you can allow for your remember allow for your spacer you can mark your tile like so which I've
done there because it's a dark tile you can see the pencil line's not really showing so you could
use a marker pen and just mark this off with a marker pen as you can see it's a red marker
and you can see the line a lot better so like I say I've marked that so obviously when I've
cut my tile through I'll then reverse that tile around and that will be the distance that I've got
cut to the wall so I've done that end what we do is turn the tile around again allow for your spacer
and just mark that out now what I want to do is take out my red line so I want to cut to the full
size tile to the right hand side so what we do we just go over to the wet the ruby cutter and I'll
show you this so we place this down I know that I want to take my line out so we just adjust the
the arm so I want to take my line out now if you've got a lot of tiles to cut
what you could do is set the gauge which is this this mechanism here it locks into place now if
you've got six or seven tiles to cut and you know your wall's straight what you could do is just cut
these tiles and once you place them against your gauge your cut tile will be exactly the same all
the way through so what we do we place this on onto the tile onto the ruby tile bed and I'll show you
on this particular cutter we've got a wheel this will score the tile we bring the
tile cutter back on itself release the arm and then we push the arm down and it will snap the tile
so if I just show you that we just score that through like so which we've done if you can see that score line
there and then we push the arm down and then don't be frightened of it just push it down
and your tile snaps and as you can see that's a nice clean break so what we do is just take
take our tile over before we start putting adhesive down we just hold that in place
and as you can see I've got a nice gap for my tile spacer and a nice gap to the wall
so what if you're using rapid set adhesive what you want to do is just lay this down
uh don't put any adhesive on it yet don't knock up any adhesive like so if you're using rapid it
goes off too quick what you want to do is just um cut these tiles in once you've once you've done
your cutting then you knock yourself some adhesive up and then start laying them so I'll cut cut my
next tile and then I'll show you how to do the L-shaped tile okay I've just cut my second tile
into my to my wall tiles now we're on to the L-shaped tile so what we want to do is we want
to place the tile on the floor and line it up with our tiles that we laid earlier and what we do is
just mark this off like so with our pencil or like I say with our marker pen now I know that we've got
skirting going on this return wall here so you know I haven't got to be tight up to this wall
so what we do is mark it there and then we pull it back on itself again allow for your tile spacer
to go in and then we cut this one to the wall line like so so that is the section we want to
take out so we take that over to our bench and then what we do if you've got a square what we
do is just square this off so we know that we're following our line when we use our wet cutter
like so and as you can see that is the area we want to take out right the machine we're
going to use for this is a ruby wet cutter fantastic bit of kit got a diamond blade in
it got a water tray underneath so obviously when you start it up the water spins onto the blade
and it keeps the blade nice and cool which allows it to stay sharp for longer again I can't stress
enough when you're using electrical equipment electrical tools cutters etc always wear your
safety glasses so we stick our safety glasses on we start our machine up and as you can see
there's water coming out of the blade now and what we do is just run this let the blade do the work
don't don't force it because you'll just blunt the blade and again and as you can see that's
given us a nice cut there so we take the glasses off and just take this over to where we're going
to lay it just dry lay this for now and just have a look make sure we're happy with that
and as you can see that's nice down that line and like I said a lot of bit of a gap there
doesn't matter because obviously I've got skirting going on there now I've cut these
because I'm using a rapid set adhesive I'll now knock up a bit of adhesive and then get these
laid don't knock up the adhesive you're going to use rapid set adhesive don't knock it up before
you've done your cutting by the time you've got done all your cutting you go back to your bucket
the adhesive's gone hard so I'll knock up some adhesive and then I'll come back and I'll relay
these right to the end and then we move on from there okay now I've knocked my adhesive up what
I'll do is I'll lay this round here so we'll just clean that off like I say normally I'd have that
all um all spreaded and I'd have just laid these straight down so what we do because we're tight
on room there we just lay this put the adhesive on the back side of the tile like so make sure
you cover the whole of the tile you don't want any air air gaps in it and by the time we've pushed
this down that all all that adhesive would have spreaded across just lay that in there like so
get a spacer get our spacer in like that again back of the tile as you start laying the tiles
you'll know how much adhesive to put on the floor or put on the back edge of the tile what you don't
want to do is put too much adhesive on the back of the tile so you're forever trying to push it
into place and then like I say once you're pushing it down all the adhesive comes through the gaps
and then you'll be a while cleaning it up so I'm happy with that and just pull that back on itself
again like so right now we get our our L-shaped tile spread the adhesive on the back of here
like so and we're just going to lay this into position always try and push it down make sure
the adhesive is key to the tile and obviously the wood that it's uh the subfloor that it's
fixing to so we push that in like so get our spacers going internally like that right okay
that's what we do now we're on a full run again we can uh we can just spread this now
and that finishes that whole area up
once you get these three tiles down okay we just put our last tile into position like so again spacers
that's nice like that that's it what we do then is just clean up the boundary edges
with your trowel it's a lot easier to do this when it's wet because when it goes hard it's
annoying me and I start chopping out with a hammer and chisel right okay so that gets all that area
done as you can see we've shown you how to cut tiles what I do is work on the far side I get
all these tiles cut get them all into position once I've cut them we remove our spacers once all
the adhesive goes off and then I'll come back and I'll show you how to knock up some grout and how
to grout this floor okay now you can see I've done all my cuts around uh the boundaries from floor
to wall now let me just show you over here now I might have a carpet in this room and obviously
I've got another L-shaped tile going on here the other problem I've got is I've got architrave
now I can cut my tile and then I can nibble it out with my nibblers which takes takes an
awful long time or just a little tip we use these little machines now which is a fine tool and
that's got a like a blade on it and what happens it buzzes goes backwards and forwards you can
adjust the speed on it and what we tend to do is we around maybe skirtings and architraves and
door stops we would just nibble the bottom of the the architrave off and I'll show you that now
instead of us nibbling this tile out what we do is we put the tile on the floor allow for the
adhesive so raise it up a little tiny bit and then what we do is just scribe that across
like so and as you can see I've got a line through there now I'll put my safety glasses on
I'll just show you this in principle how this works what we do put the safety glasses on and
get a nibbler and like I say these are a great tool they've got different speeds on them you can
slow them down or fasten them up and what I want to do is just take the bottom of that
architrave off so I'll go beyond my line so the tile slips underneath it
again always wear your safety glasses
as you can see we can just pull that piece out just needs a little tiny bit more on it
all right okay that's right out of there let me just get my little dust
pip on my little brush that I've got and just clean this out
okay now I've taken out the bottom section of my architrave I just checked out with my little
template tile and as you can see that flies underneath and once I get my adhesive underneath
there'd be a nice little gap there which I can either silicone or like I can grout in
so let's get a full tile just put that on the floor now obviously once my tile is laid I want
that to finish a little tiny bit underneath my door when my door's shut because in this room
here I want carpet this and I've got tile so I'll get a nice carpet to tile trim so what we do is
just mark this off like so and get my spirit level and what we want to do is just do this
on the inside edge of the stop and this will meet up this section here I'll just run my pencil across
that as you can see a lot of pencil line across there so right best to just measure this so I
two one two and again just up the other end and that will be two one about two one four
so that this wall is actually running out a little tiny bit so measure down two one four
just get my little tile tile my template tile just put this on my two lines and run this through
like so and then again allow for your allow for your spacer so that line runs right through
and we just run that through there
and keep that nice and square run that through and once I've cut my cut out that I need
I'll actually cut the tile down from the edge of my tile to my line so let's take it on the
start up the wet cutter and then we know our lines that we're going to follow
all right okay we just dry this off then we try it in our in our space where it's got to go
and then like I said we've got we've definitely got to cut the length down as well so
lay that in you can see that's nice and nice and tight there and then on that pencil line
we just run this across and again on our wet cutter and just cut this section off
like so dry it off again and then before we put our adhesive on the actually on the
tile itself we'll just try that again make sure we're happy whenever you're doing tile and wherever
you're cutting around orchestras you might have to just take it back and tweak it on the wet
cutter a little bit but that seems fine so we've pulled it out get some adhesive that we've got left
again just spread this with your with your knot sprout make sure you get plenty of adhesive on
this section here because that like it's quite thin might be a bit of a vulnerable part
let's turn the tile over and just slide this underneath our architrave
and we've cut off push that into place make sure you're nice and level and you're happy with that
get a couple of tile spaces place these into position like so we'll just clean that edge off
and what we'll do is we'll wait for that to uh to fully go off let the adhesive go hard we'll pull
all the spaces out and then um once the spaces are out i'll give it a wash and then we're ready
for grouting okay as you can see the floor's uh completely finished i've taken all my spaces out
all my cuts are done i've uh cleaned it out with a little scrubbing brush and a sponge um all the
water has dried between the joints left it a day now it's time to uh to obviously grout the floor
so what i've got today because we've got a grey tile i've got some um grey grey grout i've got
two buckets one with clean water one with no water which i'll add water in to knock my grout up
i've got my knocking up um spatula for my grout i've got my squeegee just got a standing knife
to undo this undo the bag i've got a sponge and if you've got any marigolds at home always best
try and wear marigolds when you're grouting because it just gets all in your fingers and
if you're using a dark grout you'll be finding that you'll be washing your hands for ages to
try and get it off right okay then so first things first put our marigolds on put them
on the right hand might help one that's two and what we do introduce a bit of water into our bucket
like so shake our grout up just split the block bag like so add the grout to the water
what you don't want to do is put too much water in i don't know if you've seen our videos before
if you stick too much water in and you've only got one bag of grout you'll find that the mixture
won't come together and it'll be too runny slowly just keep adding the grout into the water
i've got about eight square meters on this floor so it probably takes three quarters of this bag
what you want to do is knock all the lumps out of it and get a nice creamy consistency and i'll
show you that once i've brought it all together as you can see they're starting to come together now
i'll just add a bit more into there like so and that should do this once that's all brought
together that'll be just the mixture i'm looking for right okay that's the sort of mixture you're
looking for so what i'll do is just bring that together a bit more then i'll leave it in the
bucket for about five minutes and then once it's once it's been left to stand for five minutes or
so i'll then start to grab the floor okay now i've left our grout for about five to ten minutes
that's a nice consistency i'm looking for so what we do just put some grout on the floor
now because we've got white grout on our on our tile line here sometimes we do we do tape up put
some low-tech tape up save the grout riding up the the white line because this is a light grey
if i was using an anthracite dark black or something and i would do that but we'd like
so we're using a grey what we want to do is get our squeegee and then what we do is just pull it
and start working it right into the joint make sure you push it right down into your joint
like so just let the squeegee do the work backwards and forwards like that wipe it through
like so then what you've done once you've done an area just get your squeegee and wipe off the
excess as much as you can and as you're pulling it back you might see you know just have a look
over your grout make sure you've got no pimple holes or whatever like i say just work this in
nicely make sure you push it right away down into the joint because we will uh wash this floor
we've got no water in the joints at all now if you fix some grout on the same day
you've got a tendency if you like wash out your floor and there's water still between your joints
what happens is when you start to push the push the grout into the joint it reverses itself and
then the water comes to the top and it takes ages to dry anyway just keep wiping this in
a white grout is a nice grout to use so on a white tiled floor or something
three washes and you're out the door polish it up all done you find when you use a dark grout
you've got to give it at least three four maybe five washes right okay what you want to do is
carry on that procedure all the way through all over the tiles leave it for 10-15 minutes that's
what we do we leave it 10-15 minutes come back to us and i'll show you how we just wash it off
right okay we've grouted our floor all the way through we've left it for about 10-15 minutes
now it's time to start um wiping our grout off now showed you in some previous videos about
washing grout off what you want to do is get your sponge get a nice sponge as well don't have too
much water on it keep it flat and then just wipe across the joints like so you want to do this all
the way across the floor try not to make it too wet right on your first wash you just want to
keep carry out that procedure all the way through leave it another five minutes get yourself another
clean bucket of water wash again same procedure leave five minutes get another clean bucket of
water and three times should do it and i'll show you that once i've um once i've carried out the
final wash all right okay that's our uh final wash today i've given that four washes now uh
tomorrow morning that will be a little bit dusty so i'll get a nylon cloth and just give that a
good buff up and let that look lovely that floor um so another job completed thanks very much for
watching the video i hope the videos that we're showing you um at the moment are helping you to
carry out any work that you've carried out in the house yourself uh remember all your tools and
materials can be purchased through tradesupermarket.com and please stay tuned for more of Tommy's trade secrets
