How to Make a Wood Slat Accent Wall

LIVING ROOM MAKEOVER - DIY
84 followers
15 Video Views·Dec 6, 2022
Hey everyone, this is Lindy and I'm Russell from Love Create Celebrate and today we are finally
showing you how we did that flat wall in our kid's bedroom. Welcome back to our channel
where we share DIY and home renovation videos. So it was actually a really easy project. We
grabbed a couple 2x4s from our local hardware store and we cut them down to size and threw
them up in the wall and called it good. Easy. Easy. This was part of our weekend renovation
of our kid's room. If you didn't check that out I will link it up top and you should definitely
check it out. I'll show you exactly how easy it is to do. So the first thing you need for
your slot wall is some 2x4s or some 2x6 boards. You actually could use MDF to make this feature
wall as well. We didn't because we were debating whether we wanted to paint our slot wall or stain
it and if we wanted to stain it we needed to use real wood. But if you know you're going to paint
your wall you definitely can use MDF and you don't have to worry about all of this prep work.
We used our planer to make sure all of our 2x6s were smooth and the same width before we
started cutting. When you're ready you can cut all of your boards to length on the miter saw.
You'll want to cut them a little bit longer than your wall length so that you have some wiggle
room when you're putting them up. We wanted to make sure that all of our slots were true
so the next thing we did was just square off our 2x6s making sure they had one perfectly straight
flat edge. After we had planed all our boards they were just over an inch and a quarter thick
which was going to be the width on the front of our slots. We wanted the depth of the slots to
be half an inch so we used the table saw to cut our 2x6 boards into half inch strips.
We had calculated that we would need just under 30 of our slots and once we had enough we were
able to move on to sanding all of those wooden pieces. Russell took charge of sanding all of
the faces with our orbital sander while I used some 200 grit sandpaper to sand all of the edges.
I wanted to make sure that there weren't going to be any sharp corners especially since this
was going to be in our kid's bedroom. If you decided to use MDF because you were going to
paint your boards instead of stain them then you'd be able to skip this sanding step.
Once all of the boards were sanded we gave each one of them a quick coat of paint on the front
face and the side faces. We also gave one coat of paint to the wall that these boards were
going to go up against and hopefully that will just save us from doing an extra coat of paint
later on. When all of the paint was dry we brought all of the slots into the bedroom to start putting
them up on the wall. Walls are never square in a room and since we wanted to measure each
individual slot to get the right height we brought a measuring tape and a hand saw to the room with
Since we obviously couldn't put each one of these slots into studs on the wall we put construction
adhesive on the back of each of the slots to prevent any movement as it's getting nailed up
on the wall. When it was time to put the slots up on the wall we used some spacers that were actually
just scrap pieces of wood from cutting slots so that our spacing would be even as we put the
design up on the wall. We used our nail gun to nail the boards to the wall putting the nails in
at different angles as we moved up the wall to keep the boards secure and in place.
If you have to cut out around any outlets or switches we have found that the best way to do
this is with a Dremel and a flat blade. We put the slot right up on the wall,
measure and mark the areas that need to be cut out and then use the Dremel to cut out those spots.
Typically you wouldn't see smoke coming from your Dremel as you were doing this but our
blade was really dull and we hadn't had a chance to replace it so it was working extra hard for
this project. Continue along the wall cutting your boards to height and gluing and nailing
them in place until your wall is complete. When all of your boards are up on the wall use wood
filler to fill any of the nail holes that you created while you were putting them up.
Once the putty has dried you can use sandpaper or a sanding block to smooth out all of the boards
so that you're ready for your second coat of paint. The final step is your second coat of paint.
Once that coat of paint is on your slat wall is complete. Here is how that slat wall looked in
our finished kids bedroom. We used it as the backdrop for their cute little reading neck
and I absolutely love how it looks. I still can't believe that we finished this entire room
including this wall in just one weekend. If you didn't check out that weekend reno
make sure you check that out too. I also know that an awesome slat wall in a kid's bedroom
doesn't necessarily appeal to everyone so I wanted to throw in some adult furniture and
stage it as a reading nook for adults just to give you another example of how great this slat
wall could look in your home. Thank you so much for watching if you like this video please give
it a thumbs up and let us know in the comments below and as always hit that bell so you can be
notified of more great DIY and renovation videos. Thanks everyone! Thanks!
