Swedish Torches - 3 Styles of 1 log fire.

capture the moments
102 followers
7 Video Views·Dec 5, 2022
Hello, welcome back. Happy New Year to you all. Hope you all had a good Christmas, New Year.
I certainly did. Took a couple of weeks off. Much needed after last year.
It's good to be back up here though. It's not been here in a while. It's a pretty crisp cold
morning. The stream's kind of burst its banks up the top there. Running quite high down here as
well. So yeah, nice bit of four-wheel driving in. You may have noticed I've got the chainsaw with
me today. Going to be doing some Swedish one-log fires, which I'm quite looking forward to. I'm
going to do it in three, maybe four different ways. I'll see how it goes. I've got some cedar,
which we took down just before Christmas, and I'm going to get started.
Well, for the first Swedish torch, I'm going to use just this quite small one,
and this is going to be done with hand tools. Going to need my axe, baton, and a saw as well.
So I'm going to start off just by splitting this into four quarters. There is a couple of knots
at the bottom of this, so we'll see how it goes, but it's got quite a nice straight grain by the
looks of it, which is what you want. And just going to place this just off center. This is
just for control. There we go, we've got our two halves, and in half again, and then the other side.
Try and keep your bits together, because you're going to want them to fit together again. I'll
take one of these pieces, this being the top on this side, I'm going to go about two-thirds down,
get our saw, and go about halfway through, just to remove that core section, and I'll put it
back upright, and baton that out of it. And you should see there, we've taken out that core, but
we've got the core in the bottom more or less, a little bit splintered out there. We're just going
to do that for all four. So now, as hopefully you can see, you've got the four sides which fit
together, with the hole going through, except for a small shelf at the bottom. So we're ready for
our next step. We've got two corresponding corners here, and you can see that shelf, and if we turn
that around, what you want is, just above the shelf, a hole. Let's barf off here. I'm going to
look for where the shelf is, which is about there, so a bit above that. I'm going to mark it,
and just make that mark on both sides there. There we go, there's a couple of ways of doing this.
You can do a square, or a diamond, I'll probably do more of a diamond today. Bits that go together,
with a nice air hole. So it's time to put this together. All right, so at this point, there's a
couple of things you can do. You could dig this into the ground to hold it together, you could use
some twine, which will eventually burn, so depending on how flat your surface and the bottom of your log
is, may not be ideal, or you can use some wire. So I'm just going to do that today, as I have some
with me. It's just flourished wire. Loop them together, and tighten it up. Now your cores that you
chipped out, you can keep them, and you can use them just to make some fine feathers to get
this going. So they're just going to go within the core. I'm just going to break them off so they go in
easy, and that's going to help get that fire started. Right, we're just going to start putting some of
these feathers and chips inside here, and that's going to be all ready to go, and I'll light them
all together when I'm done. So let's move on to the next one. Right, excuse the chainsawing in the
background, I can't do a lot about that, but mine will be out soon anyway. So for this one, I'm going to
use this short stumpy log. I've got a barrel-eyed auger here, and this is going to be more like a
rocket stove style of Swedish torch. A bit less traditional, but hopefully just as effective. I've
never tried this before, but I've seen it done. So I'm just going to be putting a hole in through the top,
and one in through the side for air, and we'll start it off with fuel just like we do the other
one. This is the biggest long auger I've got, so hopefully it'll do. Now this is going to come in
handy, so don't discard it. Now with some careful aiming, I'm going to go in through the side and try
to match up with the other hole. So there's a hole in the side, and there's the one in the top.
I've shone my torch through it, so I know it's definitely connected. Okay, so we're looking
pretty good there. I've thickened up the two main lines there just so I can fit in some debris to burn,
but that's the third one done. Incidentally, if you do buy a Swedish torch, you can buy them like
this, kind of pre-done, because they can be mass produced with a chainsaw like that. All right, let's get
some tinder. So what do we use to get these started? We've got all your shavings and feathers that you
can do with the cores. You've got your shavings and sawdust from using the auger, and I've collected some
birch bark as well, just like a paper birch. If not, maybe if you took the tree down, you'd be able to
get some fatwood or just some man-made fire lighters, whatever's easiest for you. I've just got some
long matches with me today. The first two are up and running very well, the chainsaw one and the axe
one. This one is immense, it's going very well. As expected, the auger one is going to take a little more
to get going because of the small hole. I'll have to get myself a bigger auger, but it'll probably
burn the longest. Now, you can cook on a Swedish torch. It's best not to cut off the airflow though.
Now, one way is to just raise your pan with a few rocks or your kettle, and that allows that airflow
to still go. Now you can tell that's hot. Another way is to just put pieces of wood across, but you
can't cook for too long that way. Or you could use some kind of pot stand like so, and that kettle is
almost done. We've had a bit of an accident with the axe one, and that's because it wasn't perfectly
flat, and I left it a bit late to put weight on it like that. But if I pick it up, it should just
carry on as normal. I said pretty much as it was. I could have put some wire higher up as well to be
honest, but that's fine. It's just a demonstration one. You can see how efficient it is. It's going
again straight away. Don't worry about this floor, it's rained non-stop for a week. Nice bacon and an
egg. I'm going for take two with the tea. Seems a little more balanced now without them stones,
that was probably the problem. I didn't put too much effort into finding ones that were evenly
sized, but these ones are brilliant. Now the chainsaw one is smouldering away, and that will
burn like that for a long, long time. I could have put them slits a bit lower to be quite honest,
but this was my first time doing this type. What you can do if you want it to flame up,
still putting out some heat, is just put some more of that sort of kindling and stuff in there.
So as you can see, I just put a bit of the core of the other one in there,
and that's got that going again, and the axe one still going. So I hear you saying, Andy,
what happened to the auger torch? It's not going. Lighting all three at the same time, cooking,
filming, I couldn't give it the attention it needed. So I'm going to get back to that one now,
because I don't want to leave it fouled. So I'm just going to take the debris out of here,
just to clear it out. The same with the front hole, and I'm going to put a hole in
the opposite side. The second hole missed, but I've had another go, and it looks like we might
be up and running. I think just unblocking the holes may have helped a lot. I can safely say
this one is going well now, and because of its stability and flat top, this would be ideal for
using stones on to put your pot on. Yeah, that is going. That's really feeding through that
original hole. As you can see, this has stopped flaming, and it's not putting out as much heat
now. It definitely should take them cuts further down, but you know, live and learn. And the axe
one is actually still putting out some heat, but yeah, nearly depleted. But as you can see,
more than enough time to do a meal on. So now I can see that's burning very well. It's been
for some time now, maybe even 40 minutes, and you can see it's got a lot more time to go.
It's probably a lot more hollow inside. Like I said, it's burned through to both holes,
so it's getting loads of oxygen now, and it's like a proper rocket stove.
Now, I've eaten. I don't need this to burn for another hour, hour and a half,
so I'm going to put it out. The auger torch is out now. I'm actually sat on it. It's cooled down.
The axe one, there's a few little bits left, but you know, it's a really good burner. It really
starts up quick. The chainsaw one, definitely take your cuts further down than I did.
It's good buried in the ground. You could bury any of these in the ground, to be honest. It
doesn't really matter. It depends how flat your log and your ground is. But yeah, that was all
a success in the end. The auger one took a little bit, but that's because I was doing
10 things at the same time, really. We did get bacon and eggs.
Hope you found this interesting. There's other ways of doing these. You can put bundles of
sticks together with a gap in the middle to put some kind of fire starter and things like that.
But these, I think, are the three main ways. The rocket stove way, the Swedish axe made
torch, and the chainsaw made one, which is more of a commercial way of doing it.
Thank you very much for watching. It's good to be back.
Should be camping this weekend, and I'll see you on that one. Goodbye for now.
