🔧 BUILD OFF - Turbo vs Nitrous - First Start Ups - 35th Anniversary Special Ep 3

Rev & Roar X
259 followers
2 Video Views·Dec 2, 2022
Five weeks and less than 20 grand to build a car that reflects both the country of its origin
and its late 1980s roots, the premise of this build series proved a lot harder to execute than
both teams anticipated. Team Australia spent most of week one locating a suitable car and planning
the mods that would bring it into the 21st century within the allocated budget. The team ended week
two on budget but way behind schedule. Team USA's progress was almost the exact opposite
the guys wasted no time finding an ex-race car and getting a replacement engine. While their
progress was impressive, their adherence to the budgetary confinements was not.
So since our last episode our budget's actually taken a bit of a hit mostly because of this thing
so when you're putting more power in out of an engine obviously you need a gearbox to suit
the standard Jatco wasn't going to cut it. So what we've got here is another Jatco this one
is stronger than the last one it's been built to handle more power and it's fitted with a
three grand stall which means we should be able to get off the line if we're doing a bit of drag
racing. So our other big purchase was this sexy beast right here again this one's an ebay purchase
and we've done really well because we've managed to find this diff that will fit straight in
it's got 3.89 ratios so still really good for like highway driving and on the street
it's a full spool centre so we'll get some nice chirpy noises when you go around corners
and best of all we've got 31 spline billet axles which means on a hard launch we should
break something else that's not an axle. Mate the reason I needed you was that we're going to be
replacing the diff and to replace the live axle rear end diff in this car I need somebody to be
sitting in the driver's seat holding that brake pedal down so that when I undo everything I can
get the diff out. Rad. So I'm doing the job of a brick. That's exactly what you'll be doing today
perfect. It's probably only the second time in my life I've been able to see eye to eye with Scott
these guys don't notice but I'm actually scared of heights. You still want me to hold it?
Sometimes when I've got a bit of quiet time to myself I like to open up the good book
and just memorize a few passages. I'm a bit concerned the Americans might take this
build-off challenge like a little too seriously so I thought I'd better study up. Hey guys do
you still need me to keep my foot on the brake? Yeah man just yeah just keep on the brake yes
perfect. The slightly refreshed RB30 was ready to go back into the car. To avoid going grossly
over budget we've kept the internals mostly stock and only replaced the most needed parts
like the camshaft valve springs and head gasket. Morning. In the last episode Team USA fitted their
monstrous 408 cubic inch LS into the car. The engine went in smoothly with the help of some
modified mounting plates. Okay so what brought on having to refabricate the mid-plate? We got some
big headers. They are a two inch primary headman header with massive collectors and with all that
tubing we needed some space so we clearanced away until they fit. All right see what I mean about
these headers? They're massive but now that we're down here let's talk about this transmission. This
is a two-speed power glide transmission that came with the car however for safety's sake we sent it
down to specialty transmission and had them go through it and work their magic with it to make
sure we were going to be safe with this thing. Also we took that opportunity while the transmission
was out to utilize a Hughes torque converter. We need to go back and address something with
these headers. We had to add O2 bongs to utilize Bosch 4.9 O2 sensors. All right so I guess all
this left is to fabricate an exhaust. I have an idea. That'll do. All right like the transmission
the shifter came with the car so we lucked out there as well. Now this shifter is equipped with
an electronic solenoid to do the 1-2 shift for us. We'll be utilizing the Nexus VCU to control that
shift. So since this is a more drag race oriented car we will be utilizing a trans brake. The Nexus
R5 VCU will have full control over that function. We'll be utilizing two buttons on the steering
wheel one for the trans brake and one for line lock. Along with handling the trans brake function
we'll also be utilizing a driveshaft speed sensor that allows us to use the torque management
function of the R5 VCU. Hey guys how's it going? Hey where's Vic? Is it past his bedtime or something?
Okay so yes it's past my bedtime too. It's like basically midnight. We just got the car going
and we're gonna have dyno tomorrow. On the dyno already? Nice! Yeah. Yeah we are not.
No we're not but we're catching up we've we've got an engine in the car it's the same engine but
it's back in the car. So we screwed everything back together we had a few leftover nuts and
bolts but overall we pretty much got it back in the car and now we've just got the the bigger job
of actually like a wiring and plumbing and exhausting and all that stuff like all of the
little niddly fiddly bits. What do you reckon it's going to make power-wise? Um well do you
want on or off nitrous numbers? Well everything off nitrous because that's what we're doing so I
assume that that's what we're going to judge it on. Yeah yeah totally. Nah man that that's uh
I'm happy for you I'm really looking forward to seeing it on the dyno and and what sort of
power it makes. It's gonna be good. So we've got this boosted by Aeroflow 5862 turbo. Why this one in
particular? Well it's a fairly compact size it's going to fit where we want it to uh it's fairly
streetable we're looking at putting about 20 psi into the RB so it'll do that and best of all
it was the right price we're uh we're on a budget as you know and this fit. Actually the the real
best thing about this turbo is that it's much better than the one we had on here before.
So on the intake side of things we've got this beautiful Plasma Man plenum top bolts onto the
factory runners and at this end we've got a Bosch drive-by-wire throttle body which means we'll be
able to run with the Elite 2500 drive-by-wire it'll give us all sorts of cool things like
cruise control. Okay on the fueling side of things we've got this Plasma Man fuel rail and we've
stuffed that full of uh I think they're 1100cc Bosch injectors and that is going to sit down in
there just like that. Well mate I guess some work here is done it's uh up to you guys to finish it
off now I don't really get the whole RB thing this is all on the wrong side and the turbo's in the
wrong side so um. Back to Barrows for you mate. Yep fun as always. Thank you so much for coming
With the engine and drivetrain installed it was time for Team USA to turn their attention to
the electronics. Needless to say a build this ambitious would require all the latest and
greatest gear. The car is getting our flagship VCU the Nexus R5. The Nexus R5 is going to be
responsible for fuel ignition and nitrous control function along with any other power distribution
needs we may have on this application. The interior also received a freshen up complete
with a brand new IC7 display dash. All right we pretty much have everything wrapped up on the
interior. We lucked out and the cage was in good shape aside from a little bit of cleaning. We've
got the R5 and the IC7 display mounted. We decided to put the can keypad above us on the roll cage
so that we could easily access it and make any changes we needed to while strapped in and suited
up. We have our nitrous bottle mounted all the plumbing is done however it's time to turn our
attention to setting up the dry nitrous control. We have our intake drilled and plumbed for fogger
nozzles. These ports deliver nitrous directly into the intake runner per cylinder. This is the
best way to deliver a big horsepower nitrous system because it helps distribute the nitrous
evenly to all cylinders. The dry fogger setup is easier to tune and adjust our nitrous to fuel
ratio because we can tune each cylinder more effectively through NSP's individual cylinder
corrections. Now that the nitrous kit is plumbed, the nitrous feed line is run. Now all we need to
do is enable the progressive nitrous control inside the Nexus R5. I'm going to enable nitrous
stage one and let's get all these redifies cured before we reboot the ECU. Nitrous enabled. I want
to do it progressively. This kit is going to be progressed over race time so we want to enable
that. Great. And we have minimum coolant temp of 100 degrees. That's acceptable. Engine runtime is
five seconds. Minimum RPM is 5,000. Maximum is 8,000. I believe that's right before the rev limiter.
Minimum throttle position is 80%. Now since this is a dry fogger kit, we do need to have
fuel correction and we also have to have ignition correction. The ignition correction is going to
be applied to both banks because it is an overall system. We're not controlling it per bank. I
believe we reserved a 25 amp output from our PDM inside the Nexus R5. So yeah, we sure did. There
it is. And now we can reboot the ECU because she requires it to take all these settings we made.
That's it. The nitrous dry fogger kit is enabled. Okay, it's time to install that big bottle of
happiness which calls for a bit of subtle persuasion. That'll do it. The last thing on
Team USA's build list was a rear wing. Once again, the Motion Raceworks Santa dropped off a present
just in the nick of time. All right, that's it for our Nexus and nitrous install. This Australian
nightmare should be ready for startup soon. With the deadline looming, Team Australia finally got
some wind in their sails. The intercooler plumbing and the exhaust were back from the fabricator
and things were beginning to move quickly. Righto guys, all the old exhaust systems over in the bin.
The new one right here from TC Fabrication, he's done a cracking job. He's handmade the dump pipe
with the flange to get it done nice and quick for us. It's got a red back muffler. It's got a hot
dog in the middle here so hopefully it won't drone too much. So all I need to do now is bolt
the thing on and it should fit like a sort of factory setup. In keeping with the suburban
battlers weekend warrior theme, the exhaust while considerably less restrictive than the factory one
is still relatively subtle and almost unnoticeable to an untrained eye. Next up, we've got to keep
that charge air cool. So we've had Chris from TC Fabrications help us out with some intercooler
pipes, a super fancy little bracket. So this is the air filter. Air goes in to the turbocharger here.
Then it comes out of the hot pipe into our Plasma Man intercooler. We've got a Turbosmart
blow off valve which we may or may not use just depending. So obviously for the turbo health,
it's really good to have but being a RB30, we do want to hear a little bit of dose as well.
So this thing is adjustable. So we're going to set it up so we get a bit of flutter and we kind
of protect the turbo a tiny bit. It's also got a Haltech air temperature sensor in the intake pipe
here as well. All of the edges are all beaded here or they've got a lip on them so our intercooler
pipes aren't going to blow off with our silicon joiners and our hose clamps. So we'll slap all
this in now and then we get to the fiddly bit. With the air conditioning out of the way,
there was plenty of room for the new Plasma Man intercooler to fit. Once installed however,
despite its size, the intercooler was barely noticeable from the outside. That's not to say
the install was easy as it did take a while and it resulted in a bleeding finger or two.
Look how good this is. There's some little touches on here that are just amazing. This
little bracket that is fabbed up here that fits onto the factory crossmember there.
A couple of little other brackets in here that just sort of bolt into factory places.
This is actually better than some bolt-in kits that I've had a look at before.
Using Dave's pre-prepared loom, the wiring ended up being a fairly straightforward job.
Rightio, the engine is in. That means it is time for wiring. Now that's a job that a lot of people
really hate. Fortunately for us, we've got Dave, who loves doing things that normal people hate.
Okay Dave, what have you got going on here? So we've got our Haltech RB terminated loom.
I've sort of surgically dissected it and added in a whole bunch of stuff like our drive-by wire
throttle. We wanted to have coolant pressure and temp so I've added that in as well. We've got a
transmission temperature which I've added in as well. So when you buy one of these terminated
engine looms from Haltech, what you're saying is it's not the be-all and end-all. You can actually
modify this if you've got the skill and the know-how. If you've got the confidence, attack.
The colours are all the right colours. The shape, the joints, the breakouts, everything's in the
right place so you can't go too wrong. So it's just a really good starting point. It's a really
good starting point. I reckon 80-85% of this loom is as it was but I've just changed and added what
I needed to add and it should be ready to go. Cool. Now in this car, because it's a fairly
straightforward 1980s model thing, we could have opted for a whole bunch of different engine
management systems but I chose the Elite 2500 series. There's a pretty good reason why I did
that. I wanted to have electronic throttle control because I wanted to use the electronic throttle
for torque management, for idle control, as well as cruise control if we decide to take this thing
on a long drive. Of course I could have gone for the Nexus R5 series ECU but in this particular car,
the indicators, the headlights, the taillights, so all the wiring for that was actually pretty good.
If the wiring for that sort of stuff was starting to perish and become a problem, I would have put
an R5 in it and wired it headlight to taillight but because that portion of the harness was already
really good, I didn't really see a need to put the R5 in this car. The Elite 2500 is going to do
everything I need it to do so it communicates with all the CAN communication stuff, communicates with
the dash, communicates with the wideband. This was the right ECU for this car. Now since we bought
the R31, one of the things that I have learned is that the volts gauge and the oil pressure gauge
in the factory dash only lasted 10 years or so, then they stopped working. So if you've got one
and those gauges are actually working, well good for you, that's pretty impressive. Ours didn't.
We do want to display a whole bunch of extra stuff as well. Now that this thing, well we're hoping
that it's going to make you know twice, three times the factory power, I want to put in the
Haltech IC7 dash because I'm putting all of the engine sensors directly into the engine so I'm
instead of having an oil pressure switch, like an on, off, yes you've got oil pressure or no you
don't switch, I'm putting in a full size, so a 0-150 psi sensor so I can measure the oil pressure,
I can measure oil temperature. I'm putting a coolant pressure and coolant temp sensor in,
a combined Bosch unit so that I can measure the coolant pressure and if it happens to lift the
cylinder head or crack something, we know at least that normally the coolant pressure will go up,
that means that we can start investigating and see what's going on. As with any of this stuff,
I'm pretty good with the wiring part of it but for the fabrication it's a little bit difficult.
So in this R31, I've taken out the factory dash cluster, I've got the IC7 to put in there
but 3D Racing Solutions have come to the rescue, they've 3D printed me a cluster so all I've got
to do is put my IC7 dash straight into there, then it's got the factory mounting holes,
I can bolt that straight in, almost a factory replacement. Who would have thought when they
built the R31 Skyline that I'd be retrofitting an affordable colour dash into it 35 years later.
All right, you ready? Ready. This is the bit because well I've already cranked it over,
I've built oil pressure, I've kind of got it to a point where I know there's nothing really wrong,
we've synced up the timing so now the fuel's turned on, cross your fingers.
All right. Go? Yep.
The suburban dream is alive. The suburban dream.
It's definitely got a stall converter. Being smart, that's how it's shifting from now on.
It's there straight away. Yeah right. Let me zip the power window up.
With just one week to go, Team USA had a complete race-ready car but their finances
were not in such good shape. Aiming high, the guys spent big and headed into their final week
with a $5,313 deficit. Team Australia's were considerably more modest which is reflected
in their spending. The car still needed a tidy up and a dyno tune but having spent within their
means, the Australian balance sheet was in much better shape with $2,476 still left in the bank.
How will all this affect the car's abilities to handle the challenges in the final episode?
Guess we'll have to wait till next week to find out.
