Here is part 2 of the Destroyer Mustang 1967 Mustang Shelby GT500. After reviwing all of the comments "Destroyer Mustang" Got most of the likes, so lets go ahead and stick to Destroyer for this build :) On this episode i put together about 3 episode into one, deleted stuff that wasnt needed and removed some legal terms to be compliant.
What's going on guys and welcome back to the channel and we're gonna do the cowl repair
We're gonna start doing the cowl repair. The cowl basically is made out of two parts. It's like sandwiched together
We got the top and the bottom. This is the bottom piece right here
You put the flashlight like that. You can see all the spot welds
It's a day night difference
So what I'm gonna do now is I'm gonna use my flashlight
And then I'm gonna use my marker
And for every spot weld, I'm gonna put a center like that like that like that
I'm gonna go around and do all of that on all the spot welds like this
That way I know exactly
where I need to
Hole punch the spots without really trying to find it and see because see if I take the hot the light away
It's kind of hard to see the spot welds, especially in the area where the light is actually shining from the top
But if I do it with a flashlight you can see all the spot welds easy
Alrighty, let's go
Basically, I pretty much separated all these spot welds right here in this area and
This is separated right here. And this bracket took forever to remove right here. I'm gonna get a new one
I'm gonna get a new one of these
But yeah, it's looking looking pretty bad underneath from what I can see developing especially on the edges
You can tell that's gonna be pretty gross underneath that
That shell right here, even though I got the car primered when it was sandblasted blasted
I was able to prime it right here, but there's stuff that we don't see over here when we're gonna open it
I'm pretty sure it's gonna look pretty bad use my little
Spot weld splitter these work really good for when you actually drill it out and then you just need to kind of
Hammer it in there and just cut whatever you can
And then I got this guy right here 90 degree angle
Really good tools that I have for that
Because you obviously can't perfectly
Drill out all the spot welds
So you're gonna have to pretty much slice the rest of it off and I'm gonna use a Dremel right here on this edge
I'm curious to see what's gonna what it's gonna look like inside because Ford never actually coated
The inside of the cows with primer or anything
it was basically just bare metal for never actually thought that these cars will last more than
seven ten years and they probably thought that they're gonna be rusted out and people just gonna abandon them and buy new cars and
yeah, now they're collectors and
It's something that has to be done pretty much on all the classic Mustangs because it was never treated from the factory
All right. So, let's see what we got here
And there we go
This is the spots that usually always weld that rust out right here
Because you get a bunch of dirty here leaves everything else water sits in here builds up in here and because this was never
Protected from the factory neither was this so I'm gonna have to clean this up paint this underneath
So that's gonna be taken care of even like something like this like how does that even happen the water doesn't sit here
It always runs down. So just like
These spots are here. How does this happen this spot?
This spot. I just don't understand. There's nothing there's no no foam
No, there's nothing that would keep the water here from going down
So why would this rust out pretty much on all four corners one here one there one there this one?
This area right here
There we go
All right. So this side is pretty bad. That one's not as bad
that one's actually better on that side like this spot has just took a little bit of a
Rusted area right here a little bit right here. But other than that looks fairly decent. I'm gonna vacuum it clean it up
Make sure there's no debris and
Then I'm gonna go ahead and start splitting
This part. All right, let's continue on and after removing the old cow
There's gonna be a lot of high spots from the previous spot welds. Let's go ahead and prep these areas
Clean them up straighten them up and then we're gonna worry about things like these holes right here
spots like this that I drilled through accidentally and
Then there's also this weird spot that I got to deal with I'm probably gonna cut out this section right here
Weld in a new square as well
So I pretty much got everything as straight as possible. And I also ended up
Fixing this corner right here because as you can see this whole piece was kind of all jacked up. It was all nice and cheesy
So I ended up cutting this out and replacing it with a newer piece
While this stuff is drying
I'm gonna make a quick little bracket for this spot because there's still some cheese in this area right here
This metal with a bunch of holes as you can see, I actually want to go ahead and make a bigger plate for the bottom
So it's reinforced because I want to install shock tower brace system from TCP
Which is total control products and that's gonna mount in this area
Go across to here and then I'm gonna go across to here and I'm gonna go across
No, it's not gonna go across here. It's gonna be like a think like a square type of reinforcement. It's gonna be nicely
Reinforced but I actually want to make sure this is actually nice and solid right here as well
It took a little bit longer to make than I expected and I did a little more spot welds
Then maybe I should but it's okay. It's more reinforced. I did it, you know, as you can see right here
I did a bunch of spot welds right there and
what I'll just have to do is
Probably tomorrow just grind them all down make it as smooth as possible and then
Go over with the welding primer again, and that's gonna be ready for
the cowl to be
Installed this will be coated inside and ready to go. I'm gonna coat this as well
So that'd be it for this video. If you're new, please subscribe
And we'll see you on the next one
See ya