How Japanese Knives Are Made With Japan's RAREST Steel

Japan Go!
60 followers
25 Video Views·Dec 1, 2022
How Japanese Knives Are Made With Japan's RAREST Steel
This is how a Japanese knife is made.
Japanese blades are known as some of the highest quality in the world.
Sharp as a samurai's katana and forged with the same techniques, these knives are works of art
and are becoming increasingly sought after amongst top chefs all around the world.
To find out how they're made, we've come to Hirata blacksmiths to see not only the
forging of the blade, but how Japan's rarest steel is processed to produce knives of unrivaled quality.
Crafting a high quality blade isn't just about the skill of the blacksmith though,
but depends heavily on the quality of the material it's made of.
To ensure the highest quality possible, they make their own steel here too.
This particular substance is known as tamahagane and is the rarest type of steel in Japan.
In fact, only three workshops in the country are still producing this material today.
This is a magnet, which is used to measure the strength of the blade.
When you're making a katana, it doesn't matter if you have too much or too little sand.
This is a very important step in the process of making a katana.
To keep the fire burning hot, an air blower is used to feed a constant supply of oxygen
into the furnace. It takes roughly an hour to fully heat, so in the meantime while Sukihira-san
continues to prep the charcoal, Nodoka-san will measure out the iron sand ready for smelting.
The ideal temperature to melt the iron is around 1300 degrees.
The inside of the furnace must be carefully monitored too, to ensure consistent conditions.
Once the inside of the furnace reaches its optimal temperature,
the coals at the top are lit and the smelting process can begin.
Small portions of the iron sand are scooped up and sprinkled on top of the furnace
every 5 to 10 minutes. This is to prevent the iron from sticking together too much
and allowing it to fall to the bottom more freely.
Yeah, I think it's really important to take care of each other.
It's great to be able to work together and be free to do whatever we want.
Over the course of the day, scoops of iron sand are added to the furnace every 10 to 15 minutes.
After a few hours, it will be time to make the first check and try and drain out some of the
impurities from the furnace. This depends heavily on the conditions inside though,
and doesn't always happen as expected.
Once checked, the outlet is then sealed up again with a ball of clay.
The slag is drained every 20 minutes, so if things don't go to plan,
adjustments can be made during the intervals.
After a few more attempts, it slowly starts to appear and is gradually filtered from the iron.
This cycle of adding iron sand and draining the slag
will continue for some time and can take around 8 hours to melt down the entire 30 kilograms.
Once all the conditions inside the furnace are just right though, you can hit the jackpot.
With the last of the iron sand depleted, it's time to break open the furnace to collect it.
The heavy segments of the furnace are separated and lifted up one by one.
At this stage, the coals inside are still very much burning,
so when they're ejected out of the furnace's main chamber, it results in a huge plume of ash and flame.
The unneeded charcoal is then scraped away and a treasure is revealed.
One solid brick of pure tamahagane steel.
It's a bit too big to work with though,
so first it will need to be pounded down and chopped up into more manageable chunks.
At this point, the steel, which is still around 800 degrees,
is plunged into a bucket of water to be rapidly cooled, so it can then be measured and sorted.
Using techniques that have been refined over centuries,
tamahagane is one of the highest quality forms of steel that a blade can be forged from.
After seeing this process in depth, it's disheartening to know that the trade is
slowly dying out, and even in Japan, it's becoming something of a rarity.
It's a rarity.
There are very few techniques left that use charcoal to make steel.
The steel we have now, which is called nanbyatton,
can be made at a very low price.
It's inefficient, compared to how it used to be.
And there are very few quantities that can be made.
What's good about it is the purity of the steel,
and the fact that it sticks together when the temperature is adjusted.
Only old tamahagane steel can do that.
The steel we have now, such as iron, doesn't stick together.
It doesn't weld or anything like that.
Now that we have the tamahagane to work with, the forging of a blade can begin.
Just like with the smelting process, the key ingredient here is fire.
More charcoal then must be chopped and the fire pit prepared once again.
Just like in the furnace, the metal must be heated to around 1300 degrees
in order to make it pliable enough to mould.
Before it is shaped though, it must be folded using a Japanese forging technique called orikashi.
The piece of steel is scored down the middle and folded back on itself
and then both sides are hammered back into one piece.
To improve the durability of the blade, this will be repeated around 10 times.
As with each fold, the carbon atoms are spread evenly throughout the material
and any remaining impurities are pushed to the surface.
As the general shape of the blade starts to form, hand beating with a hammer
will become essential to get more control over the adjustments.
Once the tang of the blade is shaped, it can now be removed from the handle.
From this small brick of steel, it is further stretched and beaten into its final form.
There are so many things to focus on when it comes to making tsukitsume.
Even if you say it's going well, it's only about 70% done.
I don't know about other people's scores,
but there are a few things that I don't agree with.
You have to keep training.
If you don't look at the fire for about a week,
your senses will start to shift.
You have to keep an eye on the fire every day.
For the entire duration of the shaping process,
the temperature of the blade must be maintained.
This means that Nodoka-san must keep up with a constant supply of charcoal for the fire.
In the olden days, women were not allowed to work in the kitchen.
There are rumors that the gods are against it.
But in the old days, women were allowed to help out with the hammer.
We don't care about that at all.
I used to do kendo.
I was wondering what the roots of kendo were,
so I eventually moved to Japan.
I wanted to have a job that goes well with the prefecture.
There are about 300 people who have a license.
There are about 50 people who can't live on the sword,
With each blow, the blade becomes closer and closer to its intended shape.
This particular piece will end up as an 18cm long kitchen knife, known in Japanese as a
You can adjust the hardness and softness of the iron to a certain extent.
The hardness changes depending on how much charcoal is mixed into the iron.
You can adjust the hardness and softness of the iron to a certain extent.
This is how you make the most suitable blade.
Nowadays, people use a lot of charcoal to make very hard blades.
They also use molybdenum and pangusten to make hard blades.
If you do that, the blade will be very sharp.
However, if you drop the blade, the blade will be too hard to fix.
Now I'm going to prepare the base for baking.
This is a mixture of clay powder, charcoal powder, and charcoal powder.
I'm going to apply this to the surface of the iron.
If you apply it thinly, it will be hard when you bake it.
If you apply it thickly, it will be soft when you bake it.
Japanese swords have to absorb the impact when they are cut.
So this side is a little softer.
If everything is hard, it will break.
I made it soft on purpose to make it flexible in practice.
I also made it easy to make when making it.
Now I'm going to bake it.
This is the process of hardening the iron.
The temperature is raised from about 750 to 800 degrees.
Then it is cured with water.
Then the steel will be very hard.
The white part is the surface of the iron.
The surface of the iron is peeled off.
I'm going to bake it again.
Now I'm going to sharpen it with a machine.
I'm going to sharpen it roughly and finish it with my hands.
I'm going to start with a machine.
This is still rough.
This is about number 40.
To ensure a smooth finish, polishing on the sanding belt must be done gradually,
stepping down the size of the grit little by little.
This is 120.
There is a pattern on the skin.
If you shift the angle of the light,
For the final stages of polishing, sandpaper just isn't fine enough,
so a whetstone will be used to produce an incredibly sharp edge.
You can step on it yourself and hold it down.
It is often said that the Japanese sword does not break, does not bend, cuts well, and is even more beautiful.
This is a symbol of the heart of the Japanese.
So, what you should aim for is to become a person like the Japanese sword.
It is the spirit of all Japanese people.
When you cut the edge of the blade,
if there is a small crack in the tip of the blade,
it will stop.
If you do it slowly, you can see it.
The edge of the blade is now complete.
If you look at the blade before sharpening on the whetstone,
the edge still has enough surface area to reflect light and looks like a white streak.
But after, the edge is now so fine that it becomes almost impossible to see when viewed straight on.
Although the blade is now finished,
it's obviously not usable until it has a suitable handle.
To ensure a sturdy fit,
the tang of the blade will require a little more shaping before the handle is fitted.
In stark contrast to the delicate polishing on the whetstone,
this calls for an angle grinder.
I'm not sure I'd try that without gloves on though.
Doesn't that hurt?
As with every other step in the process,
all of this is done by sight and feel of how the blade and handle will fit together.
The knife is now complete, with its handle fitted and surface polished to perfection,
but there's still one step to finish.
The blade must be signed by its creator.
Because the blade is made of steel,
when it touches the air directly,
it starts to oxidize little by little,
and that's why we have to prevent that.
The Japanese sword uses everything in nature.
It uses fire, water, soil, and wind.
In the end, it's the heart of a person.
It even uses the soul.
The Japanese sword combines all of these elements.
That's why I always say,
when you're practicing martial arts,
you have to be grateful to everything around you.
You have to never forget to be grateful.
That way, you'll be able to think of your opponent.
If you can think of your opponent,
you won't need to fight anymore.
And that is how a Japanese knife is made from the rarest steel in Japan.
If you like this video, then please hit like,
subscribe to the channel,
and click the bell notification for instant updates on new videos.
Thanks for watching, and we'll see you again next time.
