-Survival Fire_ How to Use a Ferrocerium Rod.

The Gray Bearded Green Beret
5 followers
2 Video Views·Nov 20, 2022
Ferrocerium rod or ferro rod is a great choice no matter what the weather conditions are.
It doesn't matter if it's cold, it doesn't matter if it's wet, it doesn't matter if it's windy.
You can count on these rain or shine.
Behind solar, the ferrocerium rod is the second most efficient means of modern basic ignition sources.
Now, when I'm talking about efficiency, I'm talking in terms of conservation of resources.
Depending on the size of the rod you're using, you can expect to get anywhere from 1,500 strikes
all the way up to around 12,000 strikes.
Honestly, these big old dudes here, I'm probably getting over 20,000 strikes with each one of those.
As a rule of thumb, I expect to get a fire with a ferro rod within three strikes.
With a three-strike rule, if I can get 1,500 strikes out of this, I expect to get 500 fires.
If I can get 12,000 strikes out of this, I expect at least 4,000 fires out of this one ferro rod.
If these are 20,000 or more, I'm getting over 6,000 fires per.
Now, when it comes to size of the ferro rod, you always want to carry the largest one you can possibly carry
for a number of reasons.
One, they're more durable.
You're going to get more fires out of it, and whenever you strike it,
there's more burning material that's going to end up in your tender bundle and a greater chance of combustion.
But you also have to think about using these when conditions are not good, when they're not perfect.
When you're freezing cold and you're losing dexterity in your hands because you're becoming hypothermic
or it's too cold outside to take your gloves off, think about how much easier it'll be to handle
one of these larger rods with a gloved hand or a hand that's cold and shivering
versus trying to use one of these little guys.
It's just not going to be that easy to handle with gloved hands,
and it's not going to be easy.
You're using some fine motor skills here just to handle this little guy
versus some gross motor skills to handle one of these big ones.
So the larger ferro rods are generally a better choice overall.
I was thinking of all the decisions that I've made that have led me up to this point right here,
I think the one decision that I'll regret the most is choosing this black t-shirt to wear on such a hot day.
I mean, it is hotter than two frisky minks in a wool sock in a forest fire out here.
This is Africa hot. This is Middle East hot.
I'm going to get some water.
Normally almost every ferro rod that you purchase, that you buy, is going to come with its own little striker.
You got anything from just a regular piece of steel to these 2.0 models,
which have a whistle integrated, which is kind of a good idea.
Kids love it.
Nothing screams rescue me like that little whistle.
But anyway, if you buy a big blank rod that you have to drill yourself, put your own lanyards on,
you kind of got to use your own.
I tend to not like these strikers as much as I like to use my knife.
I always choose a knife that has a 90 degree spine, nice sharp edge on it.
Between this one and, let me grab another one.
Oh where, oh where has my Garberg gone?
There it is.
Yeah, so, this is my Bark River Bushcrafter and a Moore Garberg.
Both of these are great examples.
Both full tang knives, both have a nice 90 degree spine.
What I like about those is, if I don't feel like using this little striker,
or if I'm using one of my bigger rods,
whew, that's hotter than Hill's door hinges,
you can use that one.
If I'm using one of these, I can use the spine of my knife as a striker.
And that works really well.
And never use the edge of your knife.
There are a few different techniques on how to actually use a ferro rod.
And really, the technique that you use is going to depend on two things.
It's going to depend on the density of your ferro rod.
Is it hard or is it soft?
And then secondly, it's going to depend on the type of tender,
you know, what size is the tender that you're trying to put these sparks on.
Is it a small pile that requires a more precise concentration of sparks?
Or is it a larger target, you know, with more surface area,
that you can kind of be, that's a little more forgiving.
You don't have to be quite so precise with the placement and concentration of those sparks.
Hey dude, check him out.
Go on now.
Alright, so the first technique that I've seen,
I like to call the spray and pray method.
Basically, what you're doing is,
you're using completely terrible technique,
and you're spraying a bunch of sparks.
You spray a bunch of sparks,
and you pray that it hits your tender and starts your fire.
This is also commonly referred to as the Middle Eastern marksmanship technique.
I think we can all agree that that doesn't work,
but I still see it sometimes.
The second technique that I think is not very effective,
but I also see a lot,
is the pin and push method.
So you pin your tender down,
or you pin your rod down close to your tender,
and with your scraper,
or with your striker,
or with the edge of your knife,
you push sparks towards the tender bundle.
A couple problems with that.
First off, if you pin the tender,
you're actually collapsing that tender,
and you're taking away some of the fluff in the air.
And then, whenever you strike,
you're smashing the tender as well,
taking air away,
and the air we know is part of the fire triangle,
and we need that.
Another problem with this technique,
is you end up pushing your tender down,
or pushing your tender off,
onto the wet ground.
And now you've got wet tender,
on top of all the other problems you have.
I don't like this technique personally,
because I always bust my knuckles.
Every time I slide down, I hit my knuckles.
This is what I call the pin and pull method.
So what I'm going to do,
is I'm going to pin my striker,
or the edge of my knife,
over my tender ball.
I'm going to take the ferro rod,
and I'm going to pull it away,
and the sparks are going to originate
from the edge of the knife,
and go straight down onto the tender bundle.
So this is a great technique
for a harder composite ferro rod,
with a large target basically.
No danger of busting my knuckles,
no danger of knocking the tender bundle off
onto the wet ground.
So this is one of my favorite techniques
to use whenever I can.
I call the next technique the thumb assist method.
Softer ferro rod,
shorter ferro rod,
I'm taking my non-dominant hand,
placing the ferro rod inside,
and I'm curling my fingers around,
and only exposing the very end of it.
Then I take my dominant hand,
with the striker,
put the striker on just the end of it,
and then use my other thumb
to assist in giving leverage and pressure,
and I'm just using the very end of the rod
with a little flick.
That's going,
that's going,
and that's going.
So that is the thumb assist method.
That's my preferred technique
anytime I'm using a softer ferro rod,
or more precise targets
that I need to concentrate the sparks on.
How do you know what type of rod you have
in order to use the right technique?
The best way to tell is
try to use the thumb assist method
on your rod.
That'll tell you right off.
So if you look at this,
if I'm trying to use the thumb assist method on this,
and I'm using my striker
just on the end here,
I'm getting zero sparks.
But if I do the same thing
on this softer rod,
if I use the thumb assist method,
I'm able to get sparks.
If you're serious about learning survival skills
on a deeper level,
I'd encourage you to go to readyman.com.
My channel there
goes a little further in detail
for those that are serious about
learning these survival skills.
You can subscribe at
joshuanyark.readyman.com
