Tommy's Trade Secrets - How To Fit Architrave

Magical Mirrors
232 followers
12 Video Views·Nov 17, 2022
Hi and welcome to Tommy's trade secrets. This short clip is all about carpentry
and how to do it right. Hopefully you'll find it useful.
Take a look at the step-by-step guide and if you like it
print it, keep it and use it. Hi I'm Andy from Tradesupermarket.com
and today I'm going to show you how to fit architrave to a door frame
exactly like this one. Tools and materials needed for this job
are architrave, set square, hammer, tape measure, pencil,
some oval nails, center punch, sandpaper, miter box, some wood glue
or alternatively some grip fill, a tenon saw or alternatively you can use
a jigsaw and please remember your safety glasses.
The architrave we're going to use today is this particular one
which is a pre-primed MDF architrave and the best thing to do
is get your set square, set it at six mil and then what you want to do
is have it set six mil from the inside edge of the frame
back. So what we do is we get our set square
and mark some lines on the timber just put a few lines all the way down
like so and then just mark your your head as well and this will link in
the head architrave to the upright architrave.
As you can see we've marked our door all the way around at
six mil and the next procedure is to get our
architrave, place it on our lines that we made earlier
and then what we do is just pencil a line on the architrave and that is the
angle we're going to take to set our first
miter in. Okay what I'm going to do today is I'm
going to use our miter block and the best thing to do
is just try and secure this to the surface that you're working off
with just a couple of screws at both ends of the miter block
and this prevents the miter block from moving and obviously you've got two
hands to cut your miter on your architrave.
Right now we're ready to cut our miter on our architrave
we've already marked that from the door frame so what we do
is we place our architrave in the miter block
we get our tenon saw use our left hand push firmly onto the architrave get our
tenon saw and make our cut. The best thing to do when
you're using the tenon saw just let the tenon saw do the work
itself just push it nice and gently through
and you'll find it a lot easier to cut. Now that piece has been cut off
so remove our tenon saw as you can see we've now got our 45 degree angle that
Right we're now ready to fit our architrave so what we do is turn the
architrave over we get our wood glue we run this
on the back edge of the architrave like so
we turn our architrave over we place it on our lines always making sure
that we've got the two lines meeting at the head
like so now there's so many different ways you can fit architrave you can
either screw it and then fill it afterwards what i'm
going to do today like i said is use these oval nails
and instead of putting it on the raised areas what we're trying to do
is we put it in a recessed area so it's a lot easier to fill
so what we do get our hammer
and soon as we get down to the surface of the architrave
we then get our center punch place this on the oval nail
and as you can see i've only got a little bit of filling today there to do
today right next step is get another oval nail
place it in the center if you just take this to the surface we
can like put the rest of our oval nails in
all the way down the architrave once we're happy with the position then
obviously we can then place the center punch on the oval nail
and then drive the nail into the wood so we continue this like i say
all the way down holding our architrave
then fix in and again bring it onto our line fix again
right now we've fitted our last nail what we do we'll grab our center punch
place it on the nail and do this all the way down the architrave
right now our architrave is fixed in position
what i'll do with the head is show the other option that we mentioned today
and that is with the jigsaw right now we get our head of the
architrave and i know that we're going to create
a 45 degree miter from top to bottom running off this miter here so what i'll
do is i'll just mark that i'm not wasting too much wood i'll turn
the wood over and just mark the back side because
when we do our cut with our jigsaw instead of doing it on the front face
where we haven't got a flat surface we do it on the back side of the
architrave right the next procedure is to get our
set square we just adjust it a tiny bit we place it
on the back side of our line hold it in place mark a pencil line
across now this is obviously the miter that we're going to cut which will link
into our upright on the right hand side so next
job is put your safety glasses on always wear
safety glasses when you're using electrical equipment
and we get our jigsaw and make sure that it's firmly in place
hold the jigsaw on our line we run the jigsaw across
and because we're using a power tool it'll leave
tiny burrs of timber so what we do is we get our sandpaper
we just rub these burrs off and then we have a nice
clean miter right now we have our miter
cut what we do is we place it on our line
and then that links into our miter that we made earlier
then obviously the other side we have our line we can then mark
our architrave and then we know that next miter
is going to start from the top and work its way out
okay now we have our miters cut at both ends
what we do is replace our architrave on our head just to make sure that
we're happy with the angles and we get our wood glue and run our
wood glue on the back edge of the architrave
then also just run a line on where the miters
are going to be joined together what we do we place this on
on our head this can be a little bit fiddly because you've got the glue on
the back side it might slip a little tiny bit but if
you hold it securely in position you'll find that it'll be okay what we
do is we hold it in position we get one of our nails
and drive it in to the surface of the timber
what we do grab another nail place it on the timber
tap it into the timber make sure the architrave is still on the line
put our nail in to the surface of our architrave
what we do we put four nails in this head today
and then finally the last one again we get our centre punch place this
on our nail drive this home and what you do is just
continue this procedure on the head and then obviously when we
fit our upright on the left hand side you continue the same procedure all the
way around right now as you can see we've got our
architrave fitted and what we want to do we had a little bit of filler left
over so what we've done is just knock some up in a little pot
and just to hide the the pin heads what we do is just wipe a little bit on
your finger place it in the groove get yourself a
little little damp cloth anything to do a little
dishcloth and just wipe that through like so
once that filler's got gone off you can then get your sandpaper
just square edge it fold it over you can place this in the groove
just wipe that up and down and that'll bring that back nice and flat
and then you're ready for undercoating and then top coating with your paint
right that's another job completed today remember all your tools and materials
can be purchased through tradesupermarket.com
thanks very much for watching today so stay tuned for more of Tommy's trade
secrets i hope you found that useful now click
below to find all the tools and materials you need for the job
there are products from loads of merchants all at the cheapest prices on
the web thanks very much for watching Tommy's
trade secrets oh would you mind rating this video and
spread the word
