Tommy's Trade Secrets - How To Tile A Wall

Magical Mirrors
232 followers
10 Video Views·Nov 17, 2022
Hi and welcome to Tommy's trade secrets. This short clip is all about tiling and how to do it right
so hopefully you'll find it useful. Take a look at the step-by-step guide and if you like it
print it, keep it and use it. Hi I'm Andy from tradesupermarket.com and today I'm going to show
you how to tile a wall exactly like this one. Right tools and materials we're going to need
for this job today are tile cutter, spacers, notch trowel, tile adhesive, spirit level, bucket with
water, sponge, tiles, selection of screws and a drill driver. Right first things first today what
we want to do is get the centre of our wall it's always best to try and get the centre section of
and then that will give us even cuts either side. So what we do is we measure the wall
overall which is 2840, 2 meters 840, so half of that is 1 meter 420.
So we just mark that with our pencil like that. Right what we do next is I'm going to set my tiles out
to the height of 420.
So I'm going to get my spirit level place it on my centre line make sure the spirit level is upright
which indicates the bubble being in the middle of the two lines. Make sure it's on my on my line
and then draw a nice straight line like so and then what we do next
as we're 420 from the from the floor we then get our spirit level
make sure it's level on the line and draw a nice horizontal line the length of the spirit level.
Now this position indicates where we're going to start with our first tile.
Right next procedure we get our tile adhesive and our notch trowel
and loading the trowel with the tile adhesive place it on the wall and then start to spread
off of our lines working onto the wall to be tiled. Don't be afraid to
load up the trowel so you spread that like so and then just line it off. Then we get our tiles that
we're going to use today and on our line we place our first tile on our horizontal line and our
vertical line just push this into the tile adhesive and we get our next tile and lay that next to it
like so. Keep following this procedure all the way along making sure that we're on our line
and today we're going to create a 3mm joint. So what we do is grab our tile spacers
we place one in the top section and then one in the bottom section that creates our 3mm
gap that we're going to use today. Place another tile spacer in and again in the bottom.
Obviously if we were using a larger tile today and there's a chance of the tile slipping
what we do is we get ourself a straight piece of timber place it on our horizontal line like so
just get a couple of small screws our drill driver and just put these into the wall.
You create this procedure all the way along the timber and this will prevent our tiles from
sliding down and we know that that is set in the position that we want them in.
Right okay we keep the tiles going onto our timber again another spacer and at the head
of the tile another spacer and then slowly we start to work up. Another tile on the end of
the tile stick spacer and just carry on with this procedure all the way along
till you cover the whole of the adhesive area. Right okay when when this is complete in this
area we then grab our notch trowel and then spread the adhesive on the area above
and then again the same procedure, tiles in,
spacer and as you can see the three mil gap is consistent all the way down. Another tile
another spacer, tile space around the outside edge push the spacer in between and as you can
see when we get to the top we've actually got a cut tile and once I finish this area then I'll
show you how to cut the tiles. Right now it's time for our cut tiles. What we do is we place
the tile and create our imaginary three mil gap. We then mark the tile with our pencil,
we then take the tile down to our tile cutter and we lightly score the tile, pull the handle back,
snap the tile and that's the tile we're going to use for our cut.
So we place that in the headline there again tile spacer one on the left side
and insert it like so and we create this procedure until we get to the end.
Right now we've cut all our tiles in we're going to work on this section
to the corner of the wall so what we do again we load the trowel up with adhesive
and then we start spreading it exactly the same procedure as before.
Off our timber what we want to do is get the adhesive right into the corner so start working
the trowel back on itself and then just clean off all the excess like so and we grab our tiles
and exactly the same as we did before place the tile in get a spacer put the spacer in between
another tile along spacer again placed in just do this all the way along until you get to your cuts
as you can see we've got another cut into the corner so what we do is mark the left hand side
of the tile creating our three mil gap for our spacer turn the tile around
place it in the cutter a light source pull the arm down this snaps the tile
so it gets placed in the corner again spacer at the top and a spacer at the bottom and then what
we do is continue this procedure all the way to the top. Right once you've tiled the section
if you leave it about say 10-15 minutes just let the adhesive go off a little bit
and then what you do is you pull your end spacers out and just make sure that the tiles are firm
and what you want to do then is just get a sponge and lightly just rub off any excess
adhesive that might be on the front of the tiles. Now once we've washed them all what we do is leave
it a day and then tomorrow we'll come back and grout it. Right that's another job completed today
remember all your tools and materials can be purchased through tradesupermarket.com
thanks very much for watching today so stay tuned for more of Tommy's Trade Secrets.
I hope you found that useful now click below to find all the tools and materials you need for the
job there are products from loads of merchants all at the cheapest prices on the web thanks very much
for watching Tommy's Trade Secrets. Oh would you mind rating this video and spread the word.
