-DIY Cat Rings Tutorial

Tech Level
93 followers
4 Video Views·Nov 16, 2022
-DIY Cat Rings Tutorial
Hey there, Heather Boyd Wire here. If you're not already subscribed to my
channel, I do weekly videos about wire art and
jewelry making. This week I have three super cool
designs for cat rings. So to make the cat rings you're going
to need your tools, the ring cone, 18 gauge wire,
and the little cat bead if you're doing that design,
and then a six millimeter bead if you're doing this design.
So to make the first design with just the wire,
I have my 18 gauge wire, and then what you want to do
is form the cat's face. So what we'll do for that
is we're going to just, with the flat pliers, just bend an ear
like that, and then you can use the round pliers to
bend it up, and then bend the other ear, get it as symmetrical as you can,
and then I'm going to use the larger round pliers to form
kind of the face around like that. You could use a pen form or even the
ring form if you wanted to. Okay, so we're going to do like a little
half circle, and then you want to bend it out on a
right angle like that, and then you're going to have to finish
this end here. So we're just going to get it so it looks more or less centered.
I could just lower that one a little bit, okay,
and then we're going to bend this end around,
and this end will get clipped off. So we're going to go ahead
and clip that one off, and then push the end in so it's
flush, so it won't be sharp, and then we'll get our ring cone, hold it
on the ring cone, and just wind it around a couple of times,
and then we're going to want to try it on the finger to make sure it's the
right size, and you want to center where the tail
is underneath the head. So go ahead and hold it with your round
pliers. If you don't have the round pliers, you
can use a pen or the end of the ring form would
work too, and you want to just form a spiral
around like that. I use these spirals in a lot of my
DIY videos, and you could always do it with the cone or the pen
or the pliers. So there we go. We've formed
the spiral, and then you need to clip the end
flush like that, and then, whoops, I've got a kitty attached there.
We're going to pinch it in like that, and then to finish it off, you
just put it back on the ring form, wiggle it around, and there you have
your little kitty with his tail. So to make the little kitty
with the bead, I have this little bead here. I'll link up below where you can
buy kitty head beads. The idea is to have the
hole go horizontal, not vertical, and you want to start by doing a little
bit of a loop so it's going to hold the bead
in place. So with your small round pliers, just do a
teeny little loop, small as you can, okay,
and then for it to be really discreet and not show,
I'm actually going to bend that loop at a right angle
like that, and then we're going to put our cat bead
on there. So here we go, and then you want this
loop thing to kind of go at the side there,
and then we also need a little loop to hold it on that side or it's going to
slide around. So let's just go ahead and bend it up,
kind of perpendicular, and then as small as you can make that
loop, that would be great, and we just want to
make a little loop. It's really just to hold the bead in place.
Okay, so we're just going to go like that just to make a little loop like that.
Might work that you just bend it on a right angle too,
but for this design I just did like a little loop there,
and then you're going to go ahead and put it on the ring form
like we did the previous ring. Wrap it around a full turn
and then finish it to the front, okay, and then same thing, you can try it on
your finger to make sure it's a good size,
and then you're going to make the spiral for the tail
just down here with the round pliers or a pen or you could even use
the end of the, you want to start it with the end of
your ring cone. You can do that just with one full turn
and then make the turns a little bit smaller
with your round pliers. You can make the spiral really as big as you like
and then we'll just get finish it with the small end
of the small pliers. Give it a little clip right there and then with your flat
pliers you can finish it off. Push it in a bit
so the end is really flush there and get your pliers and
just kind of work it, work it in a little bit to tighten up
the spiral a little bit. This one got a little bent so I'll just
try to smooth it out a little bit, okay, and then for the finishing touches
you just put it back on the ring form, wiggle it around
until it's how you like it and then you have your kitty with his little
tail. So to make the little kitty with the bead
we're going to take a 15 inch piece of wire,
18 gauge as well, put a six millimeter bead on there. This is actually called a
cat's eye bead and hold the bead in place and just turn
the wire around so it's gone like a half turn
around and then what you want to do is form the ears.
So we'll just get our flat pliers and bend one end
kind of down so it makes a bit of a sharp bend
and then you can get your round pliers and just turn them up a bit like that,
okay, that'll be between the ears and then the flat pliers
again. We'll just bend that down so we have what looks already like a
little kitty face and then hold this in place
and just bend this around like that, okay,
and then we want to, all we want to do is bend this end around so we can clip it
off. So you see it just goes like that and
then give it a little clip and work it in with your flat pliers so
that the sharp end isn't scratchy there and we continue
like we did with the other rings. So we take our ring form,
we hold it on, just careful that it doesn't slide, so we do one
full turn around and then finish it underneath the head there. Make sure
it's the size you want and form our spiral like we did before.
It's, the spiral is just a really nice way
to end it off. Clip the end so it's flush in there and
as always we just give it a little pinch with the flat pliers
so it sits nice and flat and then just adjust it on the ring form how you like
it and this one is actually super cute with the little
cat's eye bead. So thanks so much for watching the video. Give it a big thumbs
up if you like it. Be sure to subscribe to my channel for
lots more DIY wire art and jewelry making videos.
Hit the notification bell to be notified when I go live and when I post new videos
and if you would like to share photos of your work be sure to join the live wires
in my Facebook group the Wire Art and Jewelry
Makers Club where you can share photos of your work
and be inspired by others and if you don't have Facebook, no worries, you
could email me photos to info at heatherboydwire.com
and I'll share them on the community page on my YouTube channel
and if you would like to check out our wire work on Etsy
be sure to check out my shop where we do a lot of custom jewelry and wedding cake
toppers or if you'd just like to support me on
Patreon, I'll link up my Patreon account below.
So thanks so much for watching and we'll see you the next time.
