Cheap Deco wall and paint on 20FT bunk House container!! Under $350

Earn, Invest, Reap
57 followers
4 Video Views·Nov 8, 2022
Cheap Deco wall and paint on 20FT bunk House container!! Under $350
Yo! Welcome back to Containing Luxury. On this episode, we're actually going to be putting
some siding on the 20-foot bunkhouse we have here in West Palm Beach. Let's get started.
Okay, so before we get started on putting the siding on that thing, the very first thing we
want to do, because we're going to be painting it gray so it kind of matches my house back there,
is install the 2x4s, which we're probably going to have to rip down I think to 2x3s,
so I'm going to see if they have any 2x3s over at Home Depot or Lowe's to fit in the little
recessed valleys so that we have something to secure the cool little siding trim we're going
to put on this thing. So we're going to paint the whole thing gray, but before I do that,
I want to adhere the 2x3s directly to this factory paint, which is going to be a much better
bond, and then I'll paint it before I put on the siding pieces, but I want that substructure
secured directly to the factory paint on it. So we're going to run over, we're going to get,
we already have the paint because we painted the 40-foot in the front. If you guys didn't watch
that, there'll be a link to the video in the description, but so we're going to use the same
color on this one, so we're going to run over, we're going to grab some glue, grab the 2x3s that
we need, and the siding ideally, but there's shortages of material, so we'll hopefully be
able to find everything in one place. So let's find out! Let's go! Okay, so to do this job you're
going to need a large caulk gun, the same glue that we always use pretty much on all of our builds,
the Loctite PL3X Premium. It's expensive, but it works. Tape measure, a drill, some drill bits,
a framing square, an impact driver, or you could use the drill if you don't have one,
but the impact driver is going to make your life easier, circular saw, and a McDonald's Coke.
Wait, what? Maybe not the McDonald's Coke, but all the rest of this is definitely needed.
Okay, so the next thing I'm going to do is pre-drill for where we're going to put our screws.
Now, these are the screws we're going to be using. Tech screws, they're self-drilling,
which are also called self-tappers, so they can drill directly through the metal. So I want to
pre-drill the wood, but I don't want to use a bit that's going to be too big, so I'm probably just
going to pre-drill with that so it still grabs the wood as well. So a little bit smaller is my
drill bit, and I'm only going to be, because I want as few penetrations through that metal
on that container as possible, I'm only going to pre-drill probably one like maybe a foot down
from the top, and then another one about a foot down or a foot up from the bottom. Now,
this has this big head on it, and I want this to sink but still grab the wood really well.
So I'm now going to take probably that size, which will be, nope, the washers are still
going to catch it. So I'm going to go just a little bit bigger, so this monster, oh that's
the wrong drill, I'm going to put this in just to countersink it ever so slightly. So I'm barely
drilling this, okay, so I just want enough that the screw is going to sit inside that pocket.
Okay, so now when I set those screws, this tech screw, the head will sit inside that pocket,
and it won't, it will be flush, so when I put the boards across it won't be an issue.
Now what I'm going to go ahead and do is, I know that this side is my side that's going to be
facing me when I'm screwing it in because I countersunk it here, so I'm going to go ahead
and flip it over, grab my glue gun with my crazy Loctite Premium, and I like to do just like a
little S-turn down the whole thing. Now I'm using a good amount of glue, but not a ridiculous amount
of glue. It's okay if it squeezes out on the side of the container, it's not the end of the world.
I'm going to come back up here, I'm going to add a little more. This glue had been sitting for a little
while, so I just want to make sure it grabs really well. So that first part might have been a little
thicker. Now we can grab two of our tech screws, our impact driver that we know has a 5-16 head,
fits right in there, carry this guy over, try not to get glue on anything including your truck,
and we'll get the pine needle off the side, take this guy, and we'll stick it right in there.
Now you can see it's pretty flush right there, so it's sticking out at a little bit of the bottom
right here because of this weld down here. So what I'm going to do is just preset the screw so it
makes it easier for me a little bit. Now I'm going to lift it up just a hair. That's going to pull it
back ever so slightly because now it's above that weld. Okay, so now that thing is really grabbed.
You can see it's squeezing the glue out on the sides, so I know that's in there nice and tight.
Now if I really wanted to, to make this a little easier on myself, you can see it kind of pulled
the board off. These self tappers take a little while to drill themselves through, so what I could
do now that I have that piece holding itself in place, I can go and I could take a smaller drill
bit like this one. It doesn't even need to be, you actually don't want it to be that big, and this
I'll pre-drill. Grab my big ladder. I'm going to pre-drill the hole through the metal
and then the screw will do the rest. So I can pre-drill this, just kind of hold it in place,
tough metal. So you'll get spots sometimes where like you literally just cannot drill through it.
I don't know what, I snapped two drill bits, burnt out three screws on that same hole to put a
different screw at an angle just to get off of maybe there was a seam or something in the metal
here, and set this one no problem. Didn't even countersink the screw. It drove it right through
it. So if you get to a stubborn spot like that, it might happen. Just skip it and go to a different
location, and you can always fill this. I'm probably literally going to fill this with
glue just so water can't get behind here, because this is not a pressure treated board.
And now I'm going to caulk down the side with glue as well, and now fill that hole. And then
when I paint this thing, it will be completely sealed in. So it's at least an added layer of
protection, so it shouldn't rot out for a long time. But that stuff happens, so just keep that
in mind. You know, you can't always set a screw right where you want it. Also keep in mind, you
don't know what's behind that wall, or hopefully you do because you have your plan. So you might
have your whole container built out, and the siding's the last thing you're doing. Make sure
you're not putting a screw right where you have some plumbing pipes on the back side of that wall.
So you're thinking about the thickness or the length of the screw, and what's behind that wall
all the time. Okay, time to start painting. Now you're not going to see any of this, but I still
want to make sure it's covered and sealed really well. So some of it's kind of caulked in with the
glue, but I'm still going to go back and silicone afterwards before I put the siding on, so that
these boards are really well protected since they're not pressure treated. I want to make
sure they're really well coated. Florida is toasty. Okay, so now that we got all of the painting
done-ski, we're going to go ahead and I bought those 12 foot long treks, I keep calling them
treks, but they're PVC or composite deck boards. I'm going to cut them exactly in half, and we're
going to put those in just this one section, which is why I only put the backer, the substructure,
in that certain area. And I couldn't put that one directly in the middle because it would have been
on the ridge, and I want these to be as close to the end as possible. So the treks boards have these
little hidden fasteners, so we're going to hide those so hopefully we won't even see any screws
when we're done. Then we're going to put some a little aluminum channel on the ends to cover the
cuts, and hopefully it'll look pretty cool. So we'll have like the painted metal, and then we'll have a
whole section of horizontal wood that just kind of gives it some architectural dimension.
So let's get start putting those in. Okay, so we officially have all the decking up. So now
I got this aluminum angle from Home Depot, and now I'm just going to apply that crazy glue that we use
on the whole inside of it, and that's going to be our cap for the...
Hopefully that doesn't happen. That's going to be the cap. Now I want to make sure that this does
not squeeze out, so I'm trying to put it only in the corner. I'm going to very gently push this
thing on. I want to be generous with the glue, but not too crazy. When in doubt, use the inside of
your pant leg. Okay, so now I'm going to take some trusty old blue tape, get a couple pieces ready.
I'm using blue tape because it will grab, but it doesn't pull the paint off since I just painted
these today. I want to make sure that it doesn't damage the paint around that was close to the
same color as the decking, and I just sprayed them out. Now we got a fancy cap, so it doesn't have to
be perfect on the cuts, but that cap it gives you a little bit of play. So now I just got one more
to do on this side over here, and our super cool wall will be done. That's it. That's it for today,
and we got all the painting done. We got our deco wall built, and hopefully you guys liked it.
Make sure to hit the comments if you like the colors. If you want to know the color,
I'll drop it in the comments as well if you want to paint your container like that.
So as always, make sure to like, subscribe, and we'll catch you guys on the next one.
Containing luxury and our 20-foot bunkhouse that just got decked out. We out.
