Hey everyone! Today we'll be making a Native American style flute out of thin wall PVC pipe. Let me know if you are interested in making a flute with schedule 40 pipe.
Hey fellow backyard boyers, Nick here. Today we're going to be building a simple PVC pipe flute.
Now this one is going to be similar to a Native American style flute. It's going to have two
chambers and a fipple. So I'm starting off with a piece of SDR 21 pipe. This is a thin wall pipe
and this is similar to the types of pipes that are commonly found
in sprinkler systems and I believe it's similar in thickness to a lot of the pipes found in other
countries outside of the U.S. The first thing I'm going to do is cut a 16 inch piece of this pipe
and I'm also going to cut a two inch piece that we'll save for later. I've gone ahead and cut
these pieces out. This is going to become the main body of the flute. So here you can see I
cut a slit in this piece of pipe before I cut it to length and this is going to slide
over the end of the pipe and create the airway once we've got everything else cut out. So next
I'm going to use some medium grit sandpaper to remove all the letters and smooth out the surface
of the pipe because this one has some scratches and some imperfections. So I'm going to do that
to both of these pieces. So now that I've got these pieces cleaned up it's time to work on our
air chamber and our fipple which is going to make the sound. So I've gone ahead and drawn a small
rectangle that's a quarter of an inch wide and an inch long and I started it two and a quarter
inches from the end of the pipe. This is going to create our air chamber and our fipple. So I'm
going to drill this out with a quarter inch drill bit and then clean it up with a file. So now that
I've cleaned out the rectangle I'm going to go with the edge of my file and create the fipple.
That's what's going to create the sound. I'm going to file on both sides because the airway is going
to be right in the middle. We're going to cap this off and that's going to create our airway here. So
I want to bring this down just a little bit and also file from the inside.
All right here it is you can see I've sharpened it on both sides. I'm going to use some sandpaper
clean off the inside here and then we'll start working on our plug. So the next thing I do is
cut a half an inch thick plug. You can make this out of a cork or a piece of dowel. In this case
this is a piece of hardwood dowel and it's seven-eighths of an inch in diameter. So what
that means is that it'll fit easily inside of this pipe. Since the dowel is smaller than the
inside of the pipe I'm using a piece of electrical tape about one to two layers to add some body so
that it'll fit nicely. I also like doing this because it helps keep the wood from expanding
and contracting which can happen when the wood gets wet when you're playing. And I'm just pushing
it down until I have about five sixteenths of an inch. We can adjust this a little bit in a second.
So now I take this split two inch piece we cut and I slide it over the main pipe and then I bring
it down so that the edge of it lines up with the edge of the plug. Let's see how it sounds.
That's not bad. I'm going to push it down just a little bit so it's a little less airy of a sound.
That sounds pretty good. So now I'm going to start drilling my finger holes. Now I'm going to leave
this mouthpiece open but if you wanted to you could close it by either putting a one inch long
plug, wooden plug, in the end here and drilling a quarter inch hole to create your first chamber
or you can take a pvc plumbing cap drill a quarter inch hole in the end of that and place
it on the end for a mouthpiece. You can also do a little heat shaping so it looks a little closer
to a traditional style mouthpiece or you can leave it open ended like this and there's nothing wrong
with this. So I'm not tuning this flute to any particular key or scale I'm just going to use my
thumbs as a measurement and put all of my holes in here by thumb widths. So what I'm going to do
is I've marked four inches from the end. I'm going to drill my first quarter inch hole here
then I'm going to measure the next hole with my thumb and just keep drilling until I have six
holes. What I did was I drilled my first hole, measured with a thumb, drilled my next one,
measured with a thumb, and so on until I got all six of my holes. So now I'm going to clean this
up with some sandpaper and it'll be all done. So here's the flute all finished up. I'm going to
leave this one like this but you could put almost any type of finish you want. You could paint it,
you could decorate it, pretty much any finish that'll work on a pvc bow or other pvc project
will work on these. I hope you enjoyed building this flute along with me today and if you have
any suggestions for other flute videos you'd like to see me do please let me know in the comments
below. If you like this video be sure to check my channel out for more and I've also written
several books on different topics including one on making pvc pipe flutes and you can check out
the links to those in the description below. So as always thanks for watching and I'll see you
guys next time. Bye!