Adding Hairpin Legs to Furniture and Testing Gel Stain

Contruction and Beyond
55 followers
5 Video Views·Nov 2, 2022
In this furniture makeover video, I am adding hairpin style legs to an end table that I found at the thrift store. I am also testing out gel stain over a wooden drawer and a laminate tabletop surface.
I decided to go bright with this project with a discounted turquoise paint I found at Home Depot. I am unsure of the exact color but I am sure you could find something similar at your local hardware store.
Let me know what you think of adding hairpin legs to furniture! Here are the hairpin legs I ordered -
Hey everyone, welcome back to the channel where I buy furniture, refinish it, and sell it for a
profit, but most importantly I show you the full process of what I do. So in this episode we're
looking at this $13 end table nightstand that I found at the thrift store. We're going to be
painting it, we're going to be using gel stain which I never used before, and we're going to
be adding some hairpin legs down bottom here. The first thing we're going to do is remove this
drawer here. So this drawer is actually wood in the front, but we have a laminate square on the
top which is weird, but that's where we are going to be applying gel stain. But let's get sanding.
I'm using 120 grit sandpaper, but I realized I should probably tape over the laminate piece so
I don't scuff it up too much. So let's throw on some tape and then I'll use some cardboard just
to cover it up and then we can get back to sanding. To get that perfect edge with the tape
I'm using a utility knife and just cutting it and it works perfect. Okay finally we have that taped
up so we don't scuff it up with sandpaper or get any paint on it, but now we're going to sand the
entire piece. As you can tell there is white paint on it. I don't know whoever owned it tried to
wasn't done very well so we're going to sand it down a nice bit so we can get rid of any
bumps and peeling paint. We're going to use the electric sander as well on the sides
and let's not forget the inside. After sanding everything down we are going to remove this
bottom box here. So this is where we're going to be applying the hairpin legs later on in the video.
We don't want to apply, we don't want to add the hairpin legs yet because we might get paint or
gel stain on them and we want to keep them fresh looking. So just use a screwdriver and remove all
the screws. Now once the screws are removed I'm using a cat's paw to pry up this bottom box.
Just put it under and pop it up comes off pretty easily. If you don't have one of these just use
a screwdriver or something to just pop it off just like that. For the most part this full piece
is solid wood but the back end and on the back end of this box was just particle board and it was just
falling apart so good thing we are replacing it with some hairpin legs. So now we're flipping
the end table back over we're going to put some paint cans underneath so we can get under it when
we're painting and priming but first we're going to clean up this project. I'm going to use my
vacuum and then I'm going to use a damp rag just to clean up any dust. I'm using rust-oleum flat
white spray-on primer so just grab your can and we're going to throw a light coat on over this
piece. You really want to make sure you get a nice layer of primer on the bare wood areas just because
that's where we will likely see bleeds in the paint most. We're all primed and ready for paint
here's the paint I'm using it's a Bayer paint from Home Depot. I got it on the discount shelf for
one dollar guys it's a pretty good deal. This is the color we're going with so I'm just using a
regular synthetic paint brush and we're going to throw some paint on this piece. For painting with
brush my number one tip I can give you is do not apply a lot of paint at once. Go thinner because
if you go thick you likely risk the chances that you're going to have drips in your paint
grabbed a 220 grit sanding sponge and just lightly sanded the first coat before applying the second
and wipe up any dust. Then throw on your second coat but we're not going to watch the full process
so I'll just skip over that. After letting the second and our final coat of paint dry I'm going
to peel off that top tape and remove the cardboard and we're going to get down to the laminate that
is there. All right now the tape is off let's flip this end table over so we can throw on these hairpin
legs and let's dust off the cobwebs before we get started. Here are the hairpin legs I ordered on
Amazon. These are six inches long if you want to pick up these exact ones I'll put the Amazon link
in the description but friendly reminder they are Amazon affiliate links so I do get a small
commission if you guys have purchased through those links. Anyways here's what comes with
the package. You get your four legs a bunch of screws and these little pads that go on the bottom
of the hairpin legs so they don't damage your floor. I'm screwing the hairpin legs in with
just a screwdriver you can use a drill it would probably be easier but just just wanted to show
you that you can use a screwdriver. And in this clip I just wanted to show you my colorful knee
pads hope you like them. Finally after getting the hairpin legs installed I'm taking these little
protectors apply a bit of pressure and just snap them on the bottom of the legs. Now after the
hairpin legs are finished we are going to get started on gel staining this laminate top and
also the front face of the drawer. But first I wanted to apply some tape around the edges here
just so we don't get any on that nice paint. There is some sticky residue on the back corner here
on the laminate top so I just used some Goo Gone sprayed it and then rubbed it with a rag.
Then I cleaned everything up with some water and another rag. Here's the gel stain I'm using
it's Varathane and the color is Espresso. I'm using a cheap foam brush to apply this gel stain
and first I'm just dabbing it directly on the can and putting globs throughout the surface.
Then you can begin brushing it over the entire surface. Now I grabbed a clean rag and I'm just
going to begin wiping the gel stain in the same pattern that the laminates wood grain goes. So
we're going to give this a natural well as good as possible we can give this a natural wooden look.
So just wipe the top until you get the look you're looking for and we're doing the same
thing to the drawer. The drawer is actually wood not laminate so I don't know if that makes much
of a difference but we'll find out. We're going to throw it all over the drawer's front face,
the top, the sides, the bottom and then we're going to wipe it off with a rag again just like
did to the top. First of all the color I really like but I don't know if I'm a fan of gel stain.
I waited over 24 hours and the stuff was still pretty tacky. It might be the temperatures in
the garage it could be the humidity but even if you just touched it it would smudge and it was
tacky on your finger. So what I'm going to do is spray some lacquer over the gel stain areas
on the drawer and on the top here and I'm hoping that'll dry it up to touch. Here's the Waco lacquer
I'm using. It's a semi-gloss finish and it takes 30 minutes to dry so let's throw this on. After
letting the lacquer dry I came back it was dry to touch on top but the edges were still kind of tacky
where the lacquer didn't really sit well I guess. So I'm going to apply polycrylic. It's not
recommended to put over lacquer but I think it'll do the trick. It'll fill in the cracks where the
laminate meets the wood and that's where the gel stain is still pretty tacky and that should do
the trick. Alright I'm applying polycrylic to the drawer as well where I gel stained and I do my
three coats and let that all dry. I did notice a difference with the gel stain on the wood and the
laminate so I don't think it's designed for laminate so that's why it was getting pretty
tacky but on the wood it worked pretty well. But anyways let's take a look at this end table
one more time before we started on it and now let's take a look at this end table after we
refinished it and the gel stain area turned out pretty good. I guess time will tell if it is
durable or not on that laminate surface but hope you guys like this hairpin leg furniture makeover
and if you want to see more furniture flips don't forget to hit that subscribe button.
Thanks for watching everyone!
