$1250 AMD Gaming PC - Ryzen 5 1600 / GeForce GTX 1080
Oct 31, 2022
Hello everyone, I'm Ryan with PC Part Picker and welcome back to another build video. Today we're
putting together a machine based around the AMD version of our great gaming build guide
and the Ryzen 5 1600 processor. Check the description below for a link to the full part
list. Let's get started. Our motherboard for this build is the MSI B350 PC Mate. Included in the
box we have the motherboard manual, quick install guide and driver disk, the IO shield, two SATA
cables, one of which will go to our SSD and the motherboard itself. Our processor for this build
is the AMD Ryzen 5 1600. In addition to the CPU, it comes with a stock cooler and a quick install
guide. Before we can install the stock cooler, we first need to remove the brackets around the CPU
socket. Open the latch on the CPU socket, then remove the processor from the plastic packaging.
Gently place the CPU in the socket. The gold triangle on the corner of the CPU is the pin
indicator and lines up with the white circle on the PCB. Close the latch. In order to align the
text on our motherboard with the AMD logo on our CPU cooler, we need to rotate the fan by 90 degrees.
Gently pull on the sides of the fan cover to unlatch the clips, then unscrew the four screws,
turn the fan 90 degrees, reattach the fan with the screws we just removed,
then snap the fan cover back into place. The stock CPU cooler already has thermal paste
pre-applied. Line it up with the mounting bracket around the CPU socket and secure it with the
screws. Connect the CPU fan cable to the CPU fan header. We're using 16 gigabytes of DDR4-3000 Team
T-Force Nighthawk memory. Open the latches on the second and fourth DIMM slots as indicated by the
printout on the PCB. Take the memory and gently set it into place. It should click when secure.
Our case for this build is the Cooler Master MasterBox 5. It has a removable power supply
shroud, tool-less drive base for three and a half inch drives, a mount for a two and a half inch
drive, an intake fan, and one exhaust fan. Remove the front panel of the case by gently lifting up
from the bottom. You'll notice that the intake fan is in the bottom most position, but we're
moving it up to the top to provide better airflow over the motherboard and to the graphics card.
To remove the intake fan, pull on the fasteners from the front of the case.
To mount the fan in the upper position, you need to align it with the holes marked with a two.
Secure the fan with the fasteners we just removed. While we're moving things around inside of the
case, let's remove the power supply shroud and slide it out. The MasterBox 5 comes with two
mounting standoffs pre-installed. We'll need to screw in the other seven into the holes marked
A for an ATX motherboard. The standoffs and standoff tool are included in the case accessories.
Before installing the motherboard, place the IO shield in the back of the case.
Gently place the motherboard in the case, aligning it with the IO shield and the two
mounting standoffs. Secure the motherboard using the standoff screws. Connect the cables from the
case's front panel IO, starting with the HD audio. Next, plug in the hard drive LED, reset switch,
power switch, power LED, and the USB 3.0 cable. Connect the rear case fan to the CIS fan header.
Connect the front intake fan to the CIS fan 3 header. Our power supply is the TX550M from Corsair.
It's a semi-modular 80-plus gold unit with the 24-pin and 8-pin EPS cables permanently attached.
It comes with a variety of cables for different build configurations. For our build, we'll only
need to use these two. First, connect the SATA power cable, then the 8-pin PCIe cable.
The MasterCase 5 has a fan grill at the bottom of the case, as well as a fan filter. So we'll
place the power supply with the fan pointed down to intake cold air and exhaust it out the back.
Secure the power supply with the provided screws. With the power supply in place, reinstall the
and secure it with the thumb screw. Remove the 2.5-inch drive tray.
The storage for our build is the Western Digital Blue 500GB SSD.
Place it into the drive tray, then secure it with the screws.
Connect the SATA power cable and the SATA data cable to the SSD. The 2.5-inch tray can be
mounted at three different locations at the front of the case, but we're mounting ours at the back
for cleaner cables. Connect the SATA data cable from the SSD, then the 24-pin power cable from
our power supply, and the 8-pin EPS cable. Before installing the graphics card, remove the second
and third expansion slot covers. Our graphics card for this build is the EVJ GTX 1080 Super Clock II.
Open the latch on the X16 slot and take the graphics card and gently set it into place.
Secure the graphics card using the screws we just removed. Connect the 8-pin PCIe power cable.
Peel the protective cover from the front panel and place the front panel back in the case.
With all of our cables and components in place, let's flip the switch on the power supply
and press the power button to give it a quick test boot before we manage the cables.
And that's the screen we're looking for. All we have to do now is manage the cables and install
the operating system. Thanks for joining us for another successful build. Remember to check out
our cable management video and check the description below for a link to the build guide and our
completed build with additional pictures and benchmarks for this system. If you enjoyed
the content or learned anything new, please give us a like and subscribe.

