Huge 4WD Off-Road RC Car! Losi DBXL-E 2.0 4x4 1/5th-Scale Electric Buggy Review | RC Driver

Auto Associated
17 followers
11 Video Views·Oct 31, 2022
So it seems like big RC cars are the in thing right now. Check out what just landed on the workbench.
That is the Lowe's DBXLE 2.0 four-wheel drive electric smart fifth scale buggy from Horizon
Hobby. I think I got it all in there. Let's go take a closer look. Look at the size of that thing.
That thing is huge. I put the 10 scale version right over there so you guys can see the size
difference. This thing is just a monster. I'm pretty excited I get to test it because I didn't
get to test out the first version of it. This is a 2.0 and I really like the look of the first
version, but there's a lot of new stuff going on in this one. Can't wait to tell you guys about it
and let's start off with the body, which actually isn't really new. Actually,
doesn't really look like much on the outside of it is new. We've got some new graphics here. I
obviously got the Fox logo version. There's also a Losi version and both of them look pretty cool,
but since I have the 10 scale Fox version, I decided to get the Fox version of this one as
well. If you look up front here, we've got this kind of splatter effect going on. I like that.
It's a little on the dark side, a little bit muddy, but it's still pretty cool the way they
did the splatter effect on here. Got some more in the back and they even carried it over onto
the wing of this thing. Up top, we've even got this big Fox logo. That's pretty cool.
What I really like is they retain the light bar on top. That is just a beast of a light bar right
there. It's mounted in four points, so I don't think this thing's going to go anywhere unless
you really land on the roof hard, but very cool that they have that. Pretty much everything else
is unchanged. I mean, the body paneling style is the same. It's a multiple piece body. Then
on the inside here, we've got our driver figures. Pretty cool look to them. We've got just some
decals to give it some detail. If you look a little bit deeper in there, you could see a
cutout for the speed controller. There's even a cutout, so you go press the button to turn on the
speed controller. That's pretty cool, so you don't have to pull the body off. The other thing I'm
missing on this one is the tethers. The 10-scale version had the tethers on there for the body
clips. I think that's a neat touch that they should have carried over here, but again, overall,
looks very cool. Let's go over to the wheels and tires. These also have a new look to them. I think
the first version was a black wheel with a silver ring on here. Obviously, we got this gray wheel
going on with a orange ring around it this time. That really looks good with the body on there,
and this is a 24-millimeter hex. This wheel does have a metal insert on the inside of it. That'll
prevent the hex from stripping out the wheel. That's a nice touch, obviously, because this thing
has a lot of power. This is an 8S-powered buggy, and that is going to definitely put a lot of
strain on everything on the inside. Overall, I think it looks pretty cool. Let me know in the
comments what you think of the new style of this. I'm interested in your thoughts. What I also like
about this, just like the 10-scale version, just like the previous version, when you do remove
those two body clips, you just have to tilt up the body here, and then you gain access to the inside
of the buggy, so you can swap out your batteries, check things out. Definitely like the look of
that. They both look cool. There it is, the 10-scale version and the 5th-scale monster here. All right,
let me pull the body off. We'll take a closer look at the inside. So, I pulled the body off here.
It's just two additional screws that basically secure it in the back for that hinge, and then
you can see on the inside here, we've got an inner skeleton, basically, to protect the inside of the
buggy. There's an inner Lexan shell for the drivers, and, you know, pretty easy to take off
if you need to go and work on the vehicle, but I will say, if you don't have a 5th-scale tool set,
go ahead and get one. I got this one here from Dynamite. Works really well on 5th-scale vehicles.
All right, now, let's take a closer look at the inside of this thing, and, again, I didn't have
the original version of it, but I went and did a little bit of research, so I will do my best to do
a little bit of a comparison while I tell you about the new parts. Let's start off in the front. So,
up front here, we've got our multiple-piece bumper. We've seen that before on the DBXL,
but right behind it here is a new addition to this buggy, the 2.0. We have an aluminum shock
tower on here now. So, the original was plastic, and even in the rear was plastic on the original,
but now we have aluminum back here as well, and from what I saw, it also has revised suspension
geometry, so this buggy should handle a bit better than the previous version, but things that
pretty much remain unchanged. It looks like it has the same upper adjustable tie rods,
same lower arms, and these are a pretty beefy-looking arm, not a lot of flex in the arm
itself, but a little in the caster block and spindle, and these look like they've remained
unchanged as well. The only thing is with this particular setup is this plastic arm right here
on the spindle. I'm not a huge fan of that on a vehicle this size. I think that should have been
aluminum, maybe it had cast aluminum, but I did see that Lozey does have an offering for two
different types of spindles. One is a two-piece version, one is a single-piece version, a $10
difference between the two. I would probably put that on this as soon as I can. I don't know,
I'm just worried about a plastic arm on the spindle, that's just me, but again, we gotta go
out and test it and see how it holds up. Alright, the next thing here is the shock. So, the shock
now has the Fox logo on there. This is a pretty awesome shock, by the way. I mean, look at that,
we got a nice rubber boot in there, massive. I mean, just look at the size next to my hand,
really nice looking shock, and it feels very smooth and even up top. We got a nice steel post
up here to secure the shock, and it's even a quick change, so you could take the nut off the back
and move it around, which makes tuning nice and easy. Another thing that I like up front here,
we got sway bars, we actually got sway bars front and rear on it, and I probably should mention,
I probably should just go back and forth between this, since some of the parts in the front are
similar to the rear, so the shock is also similar in the rear. It's basically the same size,
we've got the Fox logo etched on there, and again, it feels really smooth, a lot of pack in
there for the size of this vehicle. Now, back up to the front. I know I'm jumping around here,
but I gotta show you guys everything. There's that inner spindle and caster block set up there.
If you look really closely, they've got a nut on the kingpin screw here, so that's not gonna back
out. Definitely like that design. There is that bulky lower arm, and then on the inside here,
we've got these aluminum plates for the hinge pins, both A, B, C, and D plates. Of course,
the inserts in there as well, and nice large pins on the inside. Now, I did go and read that
they changed up the bulkhead in the gear case in here, so this is revised, and I guess it's,
from what I read, it's much stronger than the original. I didn't go in and take it all apart,
but I did get in there, take a look, and everything looks pretty well braced on the inside.
And overall, I think the front end looks good. We've got some droop screws in here. Let me move
over to the back, since we're kind of just talking about the suspension and stuff,
and here are some really large arms in the rear of this buggy, and again, I mean, I don't think
there's much flex in these things at all, just a little bit, and you need a little bit of flex
in the arm. Something has to give so it doesn't break, and a little bit of give is fine. There
are those aluminum plates in the rear, and then the rear hubs. The rear hubs are composite plastic
as well, pretty decent in size, and they do have an optional hub for that as well, if you want to
go and swap that out. There's a number of different option parts that you can get for this
vehicle, so it is upgradable. You can go and customize it if you want to, but again, we're
just going over the stock buggy here, and things that I'm seeing, pretty good. So again, I didn't
have the original, but I like the way this thing looks. I'm pretty excited about it. Here is,
again, I believe that they changed the rear bulkhead as well, and the new rear case for the
differential from what I've read. If I'm wrong, please correct me, but it seems like they did
go and revise that. All right, why don't we take a closer look at the chassis on this?
I've got the buggy propped up here, so we can take a closer look at this chassis,
and from what I can tell, it kind of looks like it's remained unchanged, but there are some things
that I really like about this. One thing is it's got a secondary plate here, so the chassis itself
is a four millimeter thick aluminum. I'm guessing like maybe a 6061 as far as the material is,
but you know, they've got the secondary plate here in the center, which is a source of tacoing,
basically. If you're going to go and taco a big car, it happens right in the center here,
so that plate helps brace things up, and they've gone ahead here and adjusted the bracing as well,
so we've got this big composite brace in the front. We've got another long one right here
in the rear, and then a secondary one in the rear as well, so that is basically going to
firm up this chassis, so hopefully nothing happens to it when you're going for some big
air with this thing, but the layout really nice. They changed things up a bit. I think the first
generation had the speed controller over here. As you can see, it's now placed on the top,
and the battery position has kind of moved in, I believe, and kind of just centralized a bit
more for better weight distribution. As you can see, we've got the big motor over here and the
electronic equipment to offset the two batteries, so it looks like it's going to be a really balanced
chassis design, and hopefully that translates to better handling, obviously. We've got the
mudguards on the side here, and one thing I want to point out about the chassis setup is
just the little details that Lozzy has gone through basically to make sure that everything
is going to work properly. Nothing's going to happen to this, and one of the things is like
wires, so we've got wire guides. That is very cool, just to protect the wires so they don't
get caught up in the gearing or anything. We've got a gear cover here just so you don't get your
fingers caught up in the gears if you're messing around with it on the workbench or whatever.
We even have a wire guide over here for the speed controller wire to go over to the receiver
so it doesn't go near the center differential. Now, while I'm talking about chassis parts,
let's talk about the servo mount here and the receiver case. Before, it was a more simplified
setup, but what we have here is a large mount basically, and it's got a single servo in there
now, but you could go and put a dual servo setup in here. So, if you want some monster steering
power, you have the option to go ahead and do that, and then we've got the receiver box over here,
and that's supposed to be, it's weather resistant. It doesn't have a seal inside, but it keeps the
majority of the debris away from the receiver. Up front here, we do have a top plate for the
steering, so let me just talk about the steering while I'm over here. So, I've got this, I believe
it's a newer composite top plate for the steering, and underneath is the twin crank steering setup.
We've got an aluminum Ackerman bar on there, really heavy duty looking. That looks like it's
four millimeters thick as well, maybe even near the five side. I didn't put my calipers on that,
but that is pretty thick, and then we've got this dual arm on the servo saver over here. So,
underneath is the spring to damp any vibrations or any blows to the servo, but we've got the dual
arm setup with the fixed links. So, no adjustment there, but at least you know that these rods are
exactly equal, and then those rods actually go over to an aluminum servo horn on here,
really like that. That is very cool, no plastic servo horn here. Yes, the arms over here on the
crank is plastic. Again, they do have an option for that, but looks like a really nice steering
setup, and then we've got the, you know, the adjustable tie rods out to the steering spindle.
So, you go and tweak tow if you want to go and do that. So, I'll just talk quickly about the
center mount on here. So, this is a plastic mount on the front for the diff, and then we've got a
massive aluminum motor plate in the rear that spans from the motor mount area all the way over
to the differential area. So, it's all one piece, so there isn't any real deflection there. When
things are moving around, the gear should stay pretty much in line, and the motor mount, pretty
easy to adjust. Two screws on the top, one screw on the bottom, and you can slide the motor around
to go and adjust your pinion gear on there. Oh, I forgot to talk about the battery case. So,
we've got two trays for batteries. So, this is obviously an 8S capable machine. You've got to
go and throw two 4S batteries in here. It's got some spectrum packs that are going to go in,
and then we've got long Velcro straps. They're really long Velcro straps, so I think you could
put a large capacity battery in here, and, you know, you've got an option to play. You've got
an option to move around, have different batteries to go and power this thing the way you want to.
There's some foam pads in there, and they're a pretty nice setup, and the other thing that I
missed before is they actually have wire guides over here for the speed controller wires as well,
and basically just keeps everything nice and stable. You know, with larger vehicles,
these cables are flopping around a lot, and maybe if you go and nosedive into the ground off of a
jump, sometimes the connector comes unplugged, so this reduces the chances of that happening. So,
I like, you know, the little details. Again, I think they did a great job in really refining
this vehicle. All right, let's go talk about the drivetrain. So, obviously, the driveline is pretty
heavy-duty on this machine. It is fifth scale. It needs to take the abuse of the power and the
weight behind it, so the driveshafts on here are steel universal driveshafts. They've got
boots to help protect everything because I think a lot of people are going to want to go and run
this thing in the sand. They even have some paddle tires as an option for this, so I could totally
see that happening, and the rubber boots on there are a nice touch to keep all the dirt and debris
out of those working joints. Then, onto the center. So, again, it's a revised diff case,
and on the inside is just a massive differential, both front, center, and rear, and inside,
obviously, oil-filled. We've got all-metal gears on the inside, and then it's all-bearing supported.
It is all-metal shielded bearings. Then, we have a new revised out-drive cup setup on this where
it's got a through-pin, and it looks like a rubber O-ring on there to secure that through-pin
so it doesn't eject or fall off like the last one did. Again, I didn't have the last one.
Don't know exactly what it looked like, but I did read up that they went and revised that,
so it pretty much eliminates that failure there, but we also have some rubber boots,
and obviously, steel shafts go back to the center differential and from the center differential to
the rear of the vehicle. Now, the center differential on this, it has an aluminum
center cup on there, which is just a must, in my opinion, for the larger scale of vehicles because
that center diff does tend to heat up a lot. There's a lot of power going to that thing.
It has to distribute power to the front and rear so it could heat up and possibly fail if it was
all composite, but on this vehicle, they have a nice aluminum cup on there, and in fact,
it's double-aluminum machined, so it's got a really cool look to it, but on one side of the
cup is obviously a steel spur gear on there. This is a direct from the pinion to the spur.
I just went and reviewed the crate, and they went and put a transmission in there,
but this is more of an A-scale style design, and it's an inline setup, so it's not like some of
the low Z vehicles that have an offset differential. It is a full inline setup on
this particular vehicle, and with the balance and everything, I think it's going to be just
perfect for performance reasons, and then on the rear of the vehicle, pretty much the same setup
as the front. We've got a gear differential in the back, all metal gears on the inside,
oil filled, and then steel drive shafts to go out to the 24-millimeter hexes, which the wheels bolt
to. Again, all metal shielded bearings in the back, but it looks like a pretty robust drive
train, and again, we'll go out, we'll test it obviously, but from what I could tell, again,
Low Z is on point with their setup, and I definitely liked a few tweaks that they did
to the drive train as well. All right, now it's time to move on to the electronics.
The electronics in here are all spectrum electronics, so before we saw some dynamite
products in here. We had a dynamite speed controller, and a dynamite motor, and then
a spectrum radio system. Now it's all spectrum, and it's the new Firmaline, which is a very cool
line of stuff because it allows you to see the telemetry on your radio if you have certain
spectrum radios, or on the dashboard if you go and download the app and use the Bluetooth module,
but before I get into that stuff, let's talk about what's in this buggy, and up front here,
we have the S906 servo. Now it's a 30-kilogram servo, did a little bit of calculation, that
translates to about 416 ounces, inches of torque, so that's about on par with what other fifth-scale
vehicles have as far as servo rating goes, and again, you could go and swap out the servo in
here and put a dual servo setup in the buggy if you just want some more power there, but I'm
interested to see how this particular servo steers the wheels of the buggy. All right, moving a little
bit farther back here, this monster back here is the Firma 160. It's a 160-amp speed controller
from Spectrum, and this is, again, it's a monster. It's a huge speed controller in here. We've got
massive 10-gauge wire on here, cooling fan, big orange heat sink on the top with the Spectrum
logos, and it's waterproof. I should actually mention that all the electronics in here are
waterproof, so you want to go out and run in the rain. I don't really do that myself, but if you
want to do it, you can go and do it. It's got a weatherproof switch on there and the set button,
and it is a programmable speed controller, so there's a lot of different functionality that
you can go in there and tune if you want to, including punch control, and if I remember the
correctly, it was set at level 4, and it goes up to level 5, so you can go and detune it if you
want to, increase it if you want to, so that adjustability is there. It does have the IC5
plugs on here, and as I mentioned, it's a telemetry-capable system, so this speed controller
right here can relay voltage, RPM, speed back to that dashboard, back to your radio system,
and you get to see all that, which is pretty cool. All right, now right below it here is the
Spectrum Firma 780kV motor. It's a massive motor. Look at the size of that thing right there. I
think I've seen soda cans about that size, but it's pretty huge. It's got some heat sinks on here.
A little bummed that it didn't have a cooling fan or a larger heat sink to go along with it,
and maybe it doesn't need it. Maybe the Losi guys, when they were testing it, found it didn't need
it, but I probably would have liked to have seen that myself, especially, again, since I reviewed
the Arma Kraton. That had a fan and a heat sink on there. So, again, we'll see how it goes. I'll
bring my temperature gun along with me, and I will check out the temps of that as I go. As far as the
radio goes, it's got the Spectrum 6100 receiver in there. Again, the telemetry receiver with AVC,
so you could use AVC to help you with the driving characteristics. You could dial it out if you want
to. Again, use that Spectrum telemetry dashboard or the other telemetry radios to see how everything
is functioning, and, of course, you could actually go and tune things as well, such as your steering.
You could adjust your steering endpoints. This buggy does come with the Spectrum DX2E active
radio system. This is a pretty good radio system for a ready-to-run radio system. It's got
adjustability as well. You have to go through the manual, and it will tell you how to adjust
everything, but, like I said, you could go and put the Bluetooth module in the Mac and go ahead and
open up that functionality of the telemetry stuff and see it on a dashboard. You go mount your phone
to the top of the radio system. They have a phone mount for it. They have a speedometer that you
could mount to the top of it, and, again, it just allows you to see much more of what's going on
with your vehicle. All right, what else do we have to talk about? Oh, the stuff that comes with it.
So what else do you get with it? Well, when you open up the box that the 2.0 comes in, you get
the Spectrum radio, which I just talked to you guys about. You also get this massive wheel nut
wrench, and this piece right here is actually a hex wrench and a turnbuckle wrench, so you could
go and adjust your turnbuckles. They do give you the normal Allen wrenches that always come in
pretty much every kit. There's some decals, and there is an instruction manual, and this is
actually a really good manual to go through because they go ahead and they even break down
some of the tuning features of the chassis itself in there, so this is a great manual to read.
All right, guys, you know what that means. It's time to go out and test this thing out. I'm pretty
excited about the new features on this. We've got a bunch of revisions. It looks cool. I think it's
going to be awesome out there, just shredding dirt. So when you come home from a day of RC fun
and your vehicle is the same color as the surface you've been driving on, you know it was a good day.
I have been having a lot of fun with this fifth scale electric stuff, and the Losey DBXLE 2.0 has
been an absolute blast to drive. I took it out on a bunch of different test runs, went to my usual
locations, and I beat this thing up. First up, this thing is pretty quiet. Now, I guess with a
large scale vehicle, I'm just used to the gasoline engine just making a lot of noise, but this thing
is super quiet. It's almost as quiet as some of my 10 scale electric stuff, so that's what just
blew my mind when I first started ripping on the throttle of this, but let's start off with the
handling, and it handles pretty well. One thing to keep in mind is it's still a buggy, even though
it's a fifth scale machine, it's very big. It's still kind of got that buggy stance to it, so
you know, there's not a ton of ground clearance underneath that. So, you know, when I was out at
the bashing field there, there was a lot of ruts and stuff that were kind of tossing this thing
around. It's still very controllable, especially when you're using the AVC. I tried that for a
little bit, but I'm more of a full rip guy, and that's when I went and dialed it in through my
spectrum radio system. Again, I put the Bluetooth in there and used my cell phone with the dashboard
app to just put it in full rip mode, get the full experience out of it, and you know, it did handle
well. Over the jumps and stuff, it lands nice and smooth, especially if you're landing off of a big
jump onto a lander. I think that's what a lot of people are missing when they go out to drive.
They're launching off a ramp, landing on flat ground, and things can happen to vehicles when
you do that, but when you go off a big jump, you know, think about that. Think about, hey,
how's it going to land, and how could it affect the car after that, and so when I was out there
jumping a lot of that stuff, like at the BMX track, I was just trying to land it on the backside.
It lands ultra smooth. It's pretty easy to control in the air. It is a big vehicle, so the
response time is a little bit slower, but landings were good. Jumps were nice and smooth, nice and
level. I hardly ever flipped it off of a jump, but going through the ruts on the big field,
it was getting tossed around a little bit. I think there was just a little bit too much chassis roll.
It was a cool day out there, so maybe that affected the oils a little bit, but I think I'm
going to go a little bit heavier on the oils here. I read in the manual that the shocks, I think,
have 40-weight oil, and that's what they were recommending for the rebuild, so that's what I'm
guessing. They have 40-weight oil in there now, but I'm probably going to go up to a 50-weight oil,
reason being is I want to kind of get rid of a little bit of that roll, and I looked at the
rear camber link. It's already at the bottom, so there's no more adjustment there, so that's what
I'm going to do. I'm going to go swap out the oil, and I think that will just bring it up to where
I like driving it, where I'm comfortable with how it handles, but overall, great on the handling.
I think it's just going to work fine for a basher. Now onto the steering. When I first started to
drive it, it seemed like it turned a bit better to the right than it did to the left, if I remember
correctly. It was one or the other, but anyway, it just seemed like it had a little bit more steering
to one side, and that's when the dashboard, again, worked out well because I was able to go in there
and fine-tune the end points, and again, you can do that through the radio system,
just much easier to do through the dashboard. Once I did that, one thing to note is when you
do use a dashboard, it overrides the ABC, and so you just got to remember to turn the knob up if
you want full steering. So, once I went and adjusted everything, then steering was pretty
awesome, and you know, you can break the rear of the vehicle free, depending on the surface,
and so that will get you spun around for quick cornering pretty easily. It's a lot of fun to do.
This thing kind of just tears up the dirt, sends it flying, so that's a lot of fun, and overall,
the steering works well. Now, let's talk about the power, and you know, again, this thing rips. It's
pretty quiet in full rip mode. It is just a blast. It just spins the wheels. These Maxxis Creepy Crawler
tires, they do a good job of laying down the traction, putting down the power. You'll definitely
throw some dirt off of them as you're just ripping on the throttle, so you know, there's plenty of
throttle to launch off of jumps, to do corrections off of jumps, just rip around berms and stuff. It
just tosses dirt in the air. It is really, really fast, and again, it's got reverse if you do need
to back out of a problem, but power-wise, it's fast. I was able to get up to 42 miles an hour
in a dirt parking lot. Did that a number of times. Wasn't the top speed of 50, which they're
advertising. I'm guessing you need an optional pinion gear for that, although I didn't see it
noted on there, but for right out of the box, 42 is pretty much on point for some good bashing fun.
It's just the right amount of power that you need, you know, in order to launch the thing off of jumps
and rip the berms and stuff, so 42 is a good speed. Now, on to durability. Not too much to talk about.
I did go a bit wild with this because people are worried about fifth scale chassis bending lately.
People that are sending their cars just flying through the air, not caring where they land,
so that's what I did. Usually, I drive my cars and I make sure that they land well, and so I don't
really have those issues, but since some people are worried about, I just started sending this
thing off of jumps, not caring how it landed, and I did go put a straight edge ruler onto the chassis.
I could slip a piece of paper between the straight edge and the chassis. I don't think that's a big
deal for what this thing went through. There's certainly enough tolerance in the rear driveshaft
that's not going to cause any binding or anything like that, so I think the chassis is really tough
on this. They've got that extra bracing. They've got that plate in there. This seems like a solid
chassis. I did notice that the tie rod ends are rubbing on the rims in the front. Again, I did
go and extend the end points of this, so it does get full steering, so just keep an eye on that.
It doesn't rub where it could become an issue if you do go and adjust your steering on it,
but other than that, the temperatures are all within normal limits, no overheating or anything.
I did go and eject the servo plug out of this off of one of the big jumps. It just landed on asphalt,
flat landed the thing, and it actually just ejected the plug out, so all I had to do was
plug that in, but nothing else. I don't notice anything else, no excessive wear anywhere,
no grinding of any gears or anything like that, so this is a tough vehicle in my opinion. I really
do like this buggy overall. It was an absolute blast to drive. It does have buggy handling
characteristics. It can be quick and nimble, and overall, just a great machine for a large-scale
vehicle. If you are looking for something in the large-scale realm, you are an electric guy,
you want to have something fast, fun, and it's just going to deliver non-stop action. Losey
did a great job revising the DBX-LE. I would totally recommend this for some big-scale fun.
