Your Guide To Building A Complete Camp Kitchen _ Overlanding

Skill Time
40 followers
7 Video Views·Oct 30, 2022
This is the ultimate Overlander camping kitchen and it will fit in any SUV. Not only does it
make setup and takedown way easier for your campsite, but it also maximizes the storage
space in your cargo area. So let me give you a quick tour and if you want to stick around,
I'll show you how to make it. As I mentioned before, this camp kitchen can fit into any SUV
and that's because of the customizable leafs on the side that are tailored to whatever vehicle
you want to put it in. We were able to completely transform the back of my friend's Nissan Xterra
from a jumbled mess of camping gear to a highly functional camp kitchen and the best part about
this is it only cost $400. Now I know this video is a little bit long, but if you stick around at
least for the next five minutes, I'll show you the build and how it turned out. So let's take a quick
tour of the build. So the overall goal that we were trying to get with this was to have a portable
camping kitchen that we could just slide out. So the whole thing is on two foot extension slides.
One of my favorite parts about the build is how it elevates the entire floor of the cargo area
about a foot and a half and you still get all of this space on top to put all of your gear
or if you're going to keep this in your daily driver, you can put all your groceries there.
What we did was put this rubber diamond plate on top. It's really grippy, so once you put something
down, it stays in place. Now anywhere that things are meant to be placed on this camping kitchen,
we added that rubber diamond plate. So we also have it here on this drawer as it pulls out.
We have it here. We also have it in this one. As you can see, this is where the stove is and this
does not slide around whatsoever. We have done test drives and it doesn't move at all. It works
flawless. So this is meant to be a retractable tray. So you can put your gearbox on here.
You can access all your gear, get anything you want, and then when you're ready to go, you just
close it and put it away just like that. You want to get something out, you pull it out,
or if you want to use it as an eating area like a table, you can just pull it out and remove
the box. Now you could sit here, you know, have a drink, eat your meal, whatever you want. So
let's go over here. And on this side, this is really, this part kicked my butt when I was
building it, but this is a really cool part. This is the actual kitchen area. So this top drawer
is just a big, big drawer for storage and it's on coffee table hinges. So this actually pulls out
into its own table. So that means that you can keep this surface as a surface that you could put
spices, oil on when you're cooking and you still have access to everything in the drawer.
And that leads us to this, which is kind of the whole purpose for the build. And this is the
camping stove. So you can cook right here. It's really convenient to be able to just pull it right
out of the car and be able to do all of your cooking just like that. This is where this table
really comes in clutch because as you're cooking and you have all of this stuff in the drawer,
you might have that box on this tray. So you could have all of your ingredients. If you're
cooking eggs, you can have your eggs up there. You can have your pancake batter. And so as you're
cooking, you can just reach up, grab it. So that's super convenient for that. And let me show you
over here where we have the sink. So that guy goes down and then we have, we have the sink system
that just gets put underneath the back seat and it's on a French cleat. So all you have to do
is plop it in here and then push it to the side. Then these guys latch and you have a really sturdy
sink. So this is conveniently right next to the water jug specifically for this build. This is my
friend's build and he already had this. And so this was a special request so that he could quickly
pull this out, fill it with water, pop it back in, and then, you know, scrub his dishes. That way
you can use a lot less water as you're doing dishes. And it also has a drain. You just press
it down and then it drains all the water. You press it again and it closes. All of the drawer
slides on this are locking, which means that once they're out and they're locked, they don't slide
back in. So if you're, if you're parked on a hill or something like that, they're not going to be
moving. Although one thing to keep in mind if you do choose to build a setup just like this is that
how your car is parked does determine cooking. And that matters if you're making pancakes or eggs
because if your griddle is tilted even just a little bit, it does make it more challenging. So
you are going to have to be aware of how you're parked, but this whole thing is graded against
the grade of the car. So if your car is parked level, this whole thing is level as well.
So as long as you can get that set, you will be cooking on a level surface. So another really
cool aspect about this build, before we move on, is that we can utilize the small storage
compartment at the bottom of the cargo area. So when we pull out this tray, we have access down
there and it's probably pretty hard to see. There's hardly any light. There's a few cubic feet of
space down there that you can store jumper cables, you can store your car jack, things like
that, you know, that you're only going to need in case of an emergency because it's not the most
convenient place to get to, but you can. And it is a lot easier to access if you fold these metal
seats down, then you can reach right in there. And one of my favorite parts of this build has to be
the leafs. So we built these leafs so that they could fold in and fold out and you could have
complete access to all of the stuff you need to store. So my friend stores water jugs, stuff like
that, and once he drops it in, he just drops those closed and now he can use all of this space
up here to store more gear. And then when you get to the campsite, you can just open these up,
grab your gear out, whatever you need, and close them back down. Or you can reach back through here
and get whatever you need. This is also a really good spot back here to store the collapsible sink,
but most likely this is going to be a really good spot to store firewood. It's not going to be
getting dust and dirt all over your gear. So all we're going to do is fold the seat down
and we can have access to anything in the back. If we were to have that storage bin, we could pull
it out, access it, or we can reach right down under here. So you can see now that I've moved it,
all of that is just a lot of usable storage space. This is also a really good way to show how
this is actually built in two parts. There's the cabinet itself and then there's the base.
And the base is bolted down to these rails in the back of the Xterra and the cabinet uses these
latches to secure it to the base. So that means that if you ever want to take this out, there's
one latch on each corner. So you just remove the latches from all four corners and you can slide
it right out. The base will stay, but if you want to remove that as well, you just have to undo all
four bolts and then you can pull it out. But chances are if you're building this, you're probably not
going to be taking the base out. And I want to mention before I get totally blown up in the
comments, yes, you will need some power tools for this. This is a beginner woodworking project
and as far as I can tell, you can't do woodworking with your bare hands. But you're only going to
need five to six power tools, and four of which are super basic. I'm talking a circular saw, a
power drill, a jigsaw, and a sander. The only two other tools we'll need are a palm router and a
table saw. Now all the handheld power tools can be found for 30 to 80 bucks if you buy Ryobi like I
do. The table saw brand new was 300, which is on the cheaper side of table saws, but if you buy one
used you can get one for 100-150 bucks. In total, you're only going to be spending $400 on tools.
That puts you at $800 for the entire project for all the tools, all the materials, everything. And
that's assuming you don't own a single power tool before this. Compare that to hiring somebody else
to do it, which I estimate would cost around $1,500 to $2,500 depending on the bells and
whistles you put in it. And you're making out like a bandit while keeping all of these power tools in
the end. So I wanted to include every single step in this project. So if you wanted to copy the exact
same thing that I did, you can totally do that. I didn't create any plans for this, but feel free to
copy any and all ideas from this video. So let's get into the build. The first thing that we need
to do is cut our pieces, and I'm not going to show every single cut because it's super repetitive,
but we're going to use a circular saw and a straight edge to break down our material to
one inch wider than we actually need. Then we're going to take it to the table saw and make that
cut exactly to the width we want. This is an extra step and it does take a little bit more time,
but it's going to mean that when you go to assemble everything, it all fits because this
is going to be a lot more accurate. So once we have all our pieces cut, we're going to start
drilling pocket holes. And when you're drilling pocket holes, it's important to make sure that
the pocket holes are going to be on the inside of the cabinet. So just be aware of how you're
orienting the boards and where you're drilling those pocket holes because we want them to be
hidden. I'll link to a super cheap pocket hole jig you can find on Amazon. It's only about 20 bucks.
Once we have all of our pocket holes drilled out, we are going to assemble everything together with
clamps, and then we're going to start screwing in all of those pocket holes one by one.
And we're going to be using an inch and a quarter pocket hole screws. Next, we're going to add the
top to the cabinet. So we'll first clamp this down, and then I put a couple screws in the corners just
to make sure it's in the right place before I go drilling all the other holes. But next, I'm going
to lay out my lines so that I know where to drill and where the center of the boards are so that I'm
not missing them with the screws. And then I'm going to pre-drill every three inches and then
go back with a countersink bit and countersink all of those holes. That way, when we drive the
screw in, it's going to fall beneath the surface. That's important because when we go to add the
rubber diamond plate at the end, it's going to sit flush, and it's not going to have all these
little bumps throughout it. You could also use pocket hole screws for this situation, but I wanted
as much rigidity as possible so I could add more screws this way, and they are a little bit stronger
than traditional pocket holes by drilling straight through. And since I was putting the rubber diamond
plate on top, it doesn't matter because no one's ever going to see any of these screws. Next, we're
going to assemble the drawer box and screw that together as well. And I used a doweling jig here
for no specific purpose. I thought, hey, I have this, maybe it'll add some extra strength, and it
might be a little bit easier to assemble. So I drilled some dowel holes and I inserted some
dowels. But really, you don't need that at all. You can just use pocket hole screws like I ended
up doing here as well, and you can just screw this together. The next thing we're going to make is the
drawer tray that goes underneath the drawer box, and this is going to hold our camping stove.
To build this, I'm using two-inch strips on the bottom just to add some extra rigidity and to be
a place for the drawer slides to mount. So I first use an 18-gauge brad nailer to tack them in place
just so it's a little bit easier to screw, and then I'll screw down into that. You do not need
a brad nailer for this. I just had one, so I used it. If you like this video so far, you should
consider giving it a like. That tells Google to show it to more people. Next, we're going to add
the drawer slides, and I'm just using some spacers to get them up and at the same height on both
sides, and then I'm first screwing the drawer slides to the inside of the cabinet carcass,
and then I'm inserting the drawers and screwing those same drawer slides to the inside of the
drawers. It's super simple, and I'm not going to go super into depth in that in this video
because there's so much to cover, but if you do want to see that, I'll have a link to the end of
the video, and you'll be able to go to another one of my videos where I go very in-depth about
installing drawer slides. With the drawer slides installed, we'll just put these drawers back in
place and see how they function. So next, we're going to build the drawer tray on the right side.
Again, I'll tack this in place with a couple brad nails so that I can screw it down,
but the difference is that this time we're using pocket hole screws, and that's because I didn't
want the screws on the top of this surface because initially we weren't planning on putting rubber
diamond plate here. That was actually an afterthought. We realized we had some extra,
and so we decided to put that on there, but this was originally just going to be painted,
and then we're going to install the drawer tray, and one quick trick is to add some playing cards
underneath the drawer as you're installing it. That way, it'll have just a little bit of extra
wiggle room. One pair of the drawer slides happened to be a little bit faulty, and so I had to adjust
the locking mechanism to get it to lock here, but once I took off a little bit of material,
everything worked fine. You shouldn't run into that issue, and if you do, you can just send that
drawer slide back to Amazon, and then you can order a new one. Next, I installed the coffee
table hinges, and so again, I just used some clamps to hold it in place while I drilled it in,
and the trick to installing coffee table hinges correctly is to make sure that the top portion
that screws to the coffee tabletop is perfectly flush with the opening of the cabinet, so that
means that when you put the tabletop on it, it's going to sit flat. That's going to tell you exactly
where you need to place those hinges on the sides. Then, I use a hot glue trick to add some hot glue
before I put the coffee tabletop on the drawer. That way, when I open it, it's going to maintain
its exact positioning. Then, I'll pre-drill and screw from underneath, and it's in the exact spot
that we want it, and it opens and closes perfectly. So next was to attach the drawer faces, and this
is a really simple process. This top drawer face has no handholds in it at all, so we're just going
cut a rectangle to the right size, and then we're going to use the hot glue method again to stick it
in place. Then, we're going to open it and very gently screw it from behind. Adding a clamp here
will also really help, but we're going to add four screws from the back to make sure that that's
really on there. For the bottom drawer face, this is where things get complicated because we have to
drill out some handholds for the actual drawer pulls. So I did a test on a scrap piece of wood,
and I used an inch and three-eighths drill bit to drill out a hole, and I found that was a really
good size hole, but the issue is that it needed to be longer. So what I ended up doing is drilling
two holes that are about an inch or two apart, and then using the jigsaw to cut between them to make
a large oval. After the test piece, I found that that was a perfect way to go about it, so I can
move on to actually replicating that test cut on the real cut. I used a ruler to mark exactly where
I wanted the center of these holes to be before I went drilled them out and cut the holes. Now,
I know I'm using a drill press here, and that wasn't included in the in the tools that I'm
talking about, but just like with the brad nailer, this is totally unnecessary. I have it, so I'm
using it. I actually got this for free and refurbished it myself, but you can just use a
power drill for this. You can use a hand drill and get all of the exact same results, but making
these hand holds is really easy. Once you drill those two inch and three-eighths holes, we're just
going to draw a straight line between both of the edges and cut that with a jigsaw. Then we're going
to use our sander and sand everything to get all the marks out, and take a little bit of sandpaper
with our hands and get in the holes to make sure that that's also smooth. Then using the same hot
glue method, I attached this drawer front and screwed it through the back. And again, playing
cards are super helpful when you're installing any drawer faces because they allow you to make
micro adjustments so that you can get everything to the right levels that you want. And the last
drawer face to install was the one for the right drawer tray, and the same exact method was used.
I attached it with hot glue, and then I screwed into it from the back. Next, I popped off the
drawer top. I scraped off the hot glue using a putty knife, and then I brought it over to my
workbench so that I could route out a little groove to use as a handle. And I'm just using
that cheap Ryobi palm router. I did this in two or three passes, but once it was done it was a
really nice ergonomic way to open up that drawer top. Then I reattached that drawer top, and that
was good to go. The next thing to do was to add some plywood edge banding to the right side of
the cabinet carcass so that it would match the protrusion of the drawer faces. So using some
glue and painter's tape, I attached that to the drawer box and then let that dry. Now that the
cabinet carcass is essentially done, I moved on to building the base. And I first took some
measurements to know how wide and how long it needed to be, and then I cut three-inch strips
on the table saw. And I'm using these three-inch strips to make the base. And in order to attach
these together, I'm going to be cutting some half-lap joints. And this cut is really easy to do.
You just set the table saw blade to half the thickness of the material, and then you do a
bunch of cuts until all that material is gone. Then I bring that over to the workbench, and I
use a chisel to flatten down all of those ridges so it's nice and flat. That way it's going to glue
up a lot better. And then to attach the half-lap joints, I countersunk two screw holes in each of
the joints. Then I added some glue and screwed everything down. The next thing I did was add a
couple layers of plywood to the front. And the reason I'm doing that is because this is going
to elevate the front just a little bit to where it's going to be against the grade of the car.
So if the car is parked in a level spot, the camp kitchen is also going to be level, even though
the car actually sits tilting forward just a little bit. And that's done for suspension reasons.
But we do need to make sure that the camping stove is totally level, because if it's not,
it's going to be really hard to cook on. Next, I used my trim router to rout out about an inch
and a half or so, and I did this in two passes so as to not be removing too much material. And
then I could attach my latches. I'll have a link to these latches in the description. It's only
about nine dollars for the entire pack, and they are a super cheap and really secure way to attach
this to the base. One thing to notice is I did modify two of the latches, the ones in the back,
because I needed them to work at a 90 degree angle as opposed to a 180 degree angle, which
they're designed for. So I just bent it over using some pliers. And later you'll see me, I had,
this wasn't quite enough, so I had to use a pry bar, just something metal. You can use a screwdriver
to bend it up just a little bit more so that that latch could fit underneath. Then I went ahead and
installed both of those latches in the back. Next, I used a three-quarter inch drill bit to drill
four holes in each of the corners. That way we can attach it through bolts to the bottom of the
Nissan Xterra. Then I countersunk the three-quarter inch hole with a one and three-eighths inch hole,
and that's going to allow the washer to sit all the way down at the bottom. This means I'll be
able to fit the washers and nut below the surface of the wood so they won't be in the way of the
cabinet. Now with the base done and the cabinet done, I could finally do a test fit to make sure
that all of my work wasn't going to go to waste. So I bolt the base down and then I latched the
cabinet, and that's when this happened. The drawer top was hitting the car and couldn't extend all
the way, so I spent a moment contemplating my life choices and why I ever even began this project in
the first place. But then I decided to do something about it, so I loosened all four bolts and then I
closed the trunk and pushed it as far backwards as I possibly could, and what do you know? It
barely works. This was way too close of a call. It would have been a total pain in the butt if I had
to modify that drawer top to fit. And here's a quick example of how this bolts down to the frame
like I was talking about earlier with the inch and three-quarters hole with the three-quarter
inch hole down in the middle for the bolt to come up through. Lastly, we could build the
leafs for this. So I first used some cardboard to cut out a template, and this was really easy.
I just kind of drew a line that it looked like would fit, and then I cut that out with scissors,
and then I just referenced it back up against the car's edge. Then I found out where it made
contact with the car, and I cut a little bit more off, and I just kept doing that until it fit
perfectly. So once I had the template exactly where I wanted it, I could trace that template
out onto a piece of plywood. Once it was all traced out, I added some masking tape to the top
to help it tear out. No, I'm not covering up my lines. You can actually see pencil lines through
masking tape. It's a little bit transparent, as long as it's only one layer. Then I used my jigsaw
to cut this piece out. Once this piece was all cut out, I then traced it onto another piece,
and being sure to cut just a little bit outside of the line, I left a little bit of material
on the outside. That way it will be slightly larger than my other piece, which was now my
template. Then I added some masking tape to the inside of both of these pieces, and then some
dots of super glue, and then I stuck them together, and I used the trim router with a flush
cut bit to route away all of the excess material until they were the exact same size. Then I could
use my palm sander to smooth over all the edges and make sure they're totally uniform. Then I
routed a thick chamfer around all the outside edges of the leaf, and I did that on both sides.
I also attached two angle brackets that are going to be used on either side
to support the leafs when they're fully extended. And the last thing we need to build is the sink
area. So I cut what are called French cleats on the table saw, and this is essentially two
pieces of wood that are cut at a 45 degree angle that wedge together and create a really strong
shelf. The next thing that I did was trace out the sink, and once I traced this out I actually came
in about a quarter inch on the inside of the line and drew another one, and that's going to be the
line that I'm cutting out. And that's to leave a little bit of a lip all the way around the edge
of the sink so that when we put it in place it'll stay and it's not going to fall through that hole.
Then I used a drill and a jigsaw to cut that hole out. Then I added the French cleat to the back of
this with some glue, and I tacked it in place while the glue dried. Next I drilled about eight to ten
different holes, and then we screwed through those holes into the French cleat to hold everything
really secure. Then we just plugged those holes with some dowels and sanded it flush.
We also attached the French cleat with some glue and a couple brad nails to hold it in place while
it dried. Then we came from the back and screwed it in from the inside of the drawer for added
strength. Then we could test fit it and find out where we wanted to put our latches, and we screwed
one in on each side. So now we're totally done with building it and we're going to move into
finishing it. And this is a two-step process. We first painted it black and then we added that
black rubber diamond plate on top. Now I actually brought it over to my buddy Hunter's house and he
painted this so I don't have any of that footage. So once I got that back from him I could add the
rubber diamond plate onto all of the surfaces we needed. So I rolled out the rubber diamond plate
on top of the cabinet carcass. Then I placed the hinges on top of the holes where they're supposed
to be. Then using a utility knife I cut the rubber mat underneath the hinges so that those
hinges could be seated all the way down onto the plywood and not interfere with anything. Then I
added some Gorilla Tape to the top of this and I flipped it back over and I trimmed off the excess
with a utility knife. But then once I got it back right side up I did a strength test and the rubber
diamond plate just peeled right off. That Gorilla Tape did absolutely nothing. I mean as if it
weren't even there. So I did a quick test with the Gorilla Tape and then just some standard carpet
tape and the carpet tape worked wonders. It was exactly what we needed and it's also a lot thinner
which makes it an even better candidate for what we're doing. So here's a quick test with the
Gorilla Tape on the left and the carpet tape on the right and you can see just how much more
adhesion we get with that carpet tape. So I replaced all of the Gorilla Tape with the carpet
tape and stuck everything back down on the top of the cabinet carcass and then I can move on to
doing the leafs and this is the same exact process. I just added some carpet tape through the rubber
diamond plate on top, flipped it over and then trimmed the excess with a utility knife. I did
this for both leafs and then I also did it for both drawer trays. Then I could put all of the
drawers back in and reattach those leafs and it's done. So we bolted the frame down into the back of
the Xterra, we installed the camp kitchen and then we tested the functionality and everything worked
flawless. There it is! Wow dude! It's not even close. So let's do a quick cost breakdown. I needed two sheets
of three-quarter inch plywood. I paid 60 bucks a sheet so that leaves us at $120. I needed three
24-inch pairs of drawer slides and they're $40 each and that brings us to $120 there as well.
The hardware, so the screws, nuts, bolts, that was $40. The rubber diamond plate was $70. The carpet
tape and paint was $20 and the coffee table hinges were another $20. So just tack on an extra $10
for stuff like painter's tape and sandpaper and our grand total is $400, which is incredibly
budget-friendly when you consider what we ended up with. Now I didn't have the time to go into depth
Now I didn't have the time to go into depth about installing the drawer slides, so I'll actually
have a link to that video up in the top right corner and you can go check that video out if
you want to see more in-depthly how to install drawer slides. As always, I have some affiliate
links in the description and you can go check out any of the tools that I'm using as well as all of
the products and materials like the latches, the drawer slides, the coffee table hinges, all of
that's going to be down in the description and you can go check that out on Amazon. So that's it for
this one. If you thought this video wasn't terrible, you should consider subscribing. I make DIY, home
renovation, and beginner woodworking projects constantly and if you want to see any of those
videos, go ahead and subscribe and hit the bell notification and it will alert you every
time I post a new video. I'm Clayton, The Weekend Builder, and I'll catch you in the next one!
