How to make a board and batten wall with minimal tools

Skill Time
40 followers
62 Video Views·Oct 30, 2022
In this video I show you how to make a modern board and batten wall
with just one power tool. We can do all the cuts with this
and other than that we just need to use a variety of different hand tools.
You're going to need a circular saw, square, level,
tape measure, spackle knife, caulk gun, and a hammer. For materials you'll need
some construction adhesive, caulk, brad nails, and spackle.
For the battens I'm going to be using this half inch MDF that's
three and a half inches wide. You can find this at Home Depot
in the trim section in eight foot lengths.
For me I'm going to need about 10 different eight foot boards
and since I already had a half inch sheet of MDF I just ripped mine down on
the table saw. But you can buy this at Home Depot and
it's going to be a lot easier that way you don't have to go through the hassle
of that. Just oftentimes it'll come already
primed. So the very first thing to do is find out where you want the battens to
land on the wall. There are a bunch of different
ways to do this so don't worry about doing it wrong
just look at some pictures of other board and batten walls and you can get a
feel for how you want yours to look. Once you know how long you want your
battens to be, mark it with a tape measure and then use your square to mark
a perfect 90 degree angle. This is going to be a
reference for the cut. So now you use the square as a guide and
this allows you to cut a perfect 90 degree cut. We're going to place the
bottom corner in first sandwich it there and then that will sit
perfectly flat just like that. Now that we know that it fits let's go
ahead and put some adhesive on it and then nail it on. All you need is
going to be just a hammer and these little finish
nails. But since I have it I'll be using this.
Same thing right no cheating. Getting this top piece in can be pretty
tricky so if you have an extra pair of hands that really would help
but if not just use a step stool or a chair to get you a little bit closer to
the ceiling. The important thing with these vertical
battens is to make sure that they're level.
If they're not and they're crooked it can become very apparent after painting.
Just like with the vertical battens you want to make sure that these horizontal
ones are perfectly level. So this is where you're going to want
to use your level and your hammer to kind of shim it up to be perfectly flat.
Then you can use that as a reference for the rest of the horizontal battens
to make sure that they're all perfectly straight. Now remember the construction
adhesive is what's going to stick it onto the wall.
These nails are just to hold it there until that dries.
So now we're going to go ahead and move on to spackling. The purpose of this is
to make sure that we can fill in any cracks
so that when we paint it goes on real smooth
it looks like it's all just one piece. Now it's time
to move on to caulking. So what we're going to try and do
is make sure to cover all the gaps around the edges.
You can do it on the inside of the boards if you didn't get them close to
the wall but oftentimes this drywall is pretty flat but these
edges at the top and at the sides that's really where you need to caulk.
So do it as needed. I'm probably just going to be doing up
around the edges and occasionally in these gaps here if the primer won't
hide them. Now I'm terrible at caulking so don't
use me as an example but you want to make sure you get a
steady bead all the way across. Then what you do is run your finger
across to pull any of the excess off. And when you're doing this make sure
you have a rag on you so that you can wipe off
that excess from your finger to make sure we get that consistent bead.
Now that we're done building it we're going to move on to sanding off the
extra spackle and then priming and painting it.
I got some 150 grit sandpaper and what I'm doing here is just knocking down the
edges so that it's smooth. That way when we paint it you don't see
these lines. I'm not going to go into detail about
painting and prepping for it but the one tip that I do have is to
make sure you wait for the caulking to dry completely.
If you don't your tape could end up sticking to the caulking as it dries
and it becomes a nightmare to peel off the wall.
Primer is basically just very thick white paint and so what it does is
actually clog all of the pores in the MDF. That way when you go to paint
it can go on smoothly. If you chose to buy the boards directly from Home Depot
chances are they came pre-primed and you can skip that step
and go straight into painting.
And with the painting over I could call this project done.
Thank you guys for watching. This has been a really fun video to put together.
If anyone wants to build one of these themselves I encourage you to.
It's easy, cheap, and looks awesome. If you enjoyed the video consider
subscribing to my channel. I don't make weekly videos but if you
subscribe you'll get to see them when they come out.
Thanks again for watching.
