Galaxy S6 Edge Battery Replacement How To Change

Finger Family
30 followers
2 Video Views·Oct 28, 2022
Samsung Galaxy S6 Edge battery replacement. How to change the battery in the Galaxy S6 Edge. If your Galaxy S6 Edge has a weak battery here's how to change it. I hope this video is helps you to change your battery in the Galaxy S6 Edge.
Hey guys, so today I wanted to make a video to show you how to change the battery in the
Samsung Galaxy S6 Edge.
I'll include a link in the video description for any tools that I'm going to be using during
this repair today.
I just wanted to show you really quick, I'm going to be using a suction cup tool and I'm
going to be using this little thin pry tool.
Now this is a really thin pry tool, I'll link to this in the description so you can find
it.
It's the only one that I found that was thin enough to go in this reveal right here.
This is very tight on this Galaxy S6 Edge, so this is the only one that worked for me.
And we're going to be using a Phillips screwdriver size 000 for removing any screws in this phone.
If you get a tool set, just make sure that it has the size 000 in there and you should
be all set.
I'll include links for any parts that I'm going to be replacing today as well.
Anything that I think might be helpful to you, I'll include links in the video description
so check them out there.
Alright guys, so the first thing you want to do is make sure that your device is powered
off.
So go ahead and do that.
And you also want to remove the SIM card tray.
So we'll just go ahead and remove the SIM card tray.
So next what we're going to want to do is use a hair dryer or a heat gun of some kind.
I'm just using a regular hair dryer.
And we're going to want to heat all the edges here.
All the way around.
Now there's especially adhesive in the corners, but there's also some all the way around.
So you want to make sure to heat it all the way around.
Now don't get it too hot, get it quite warm to the touch.
You might have to apply heat several times.
So after you've applied some heat, now what we're going to do is you can use a little
suction cup tool if you have something like this.
What I'm going to be using in particular is a suction cup tool like this.
And what we're going to do is we're just going to go ahead and suction this on somewheres
close to the bottom.
Like this.
Then with that attached, what we're going to do is since we can pry up a little bit.
So what I end up having to do is, you almost have to heat this hotter than you think you
should.
You just have to try it by trial and error a little bit.
Give it some heat.
If it doesn't give way, give it a little more heat.
What I ended up having to do, I started right in this corner right here, as you can see.
And I got it just to where it'll start like this.
So you can go ahead and once it's pretty warm, you can just slide this around.
Now be really careful.
Just take it a little bit at a time.
Don't stick this in too far.
What I would recommend too is if you have some really thin guitar picks and stuff, what
you can do is if you make a little room so you can get this in here right beside it,
you can have that hold that so it doesn't stick back down.
And then just keep working your way around.
So what I would recommend also is just kind of pry up a little bit as you go.
This is a little unhandy to do.
Now be very careful right from this point in here, in the middle section of this phone,
to not go in very far at all when you're going through here because the Qi charging pad is
right in here.
And it comes in really close here, so you want to be really careful in this area right
in here.
You want to not go in very far with whatever pry tool that you're using.
I would recommend if you can, it makes it hard to hold up on this, but try to take the
pressure off a little bit with the suction cup tool as you go along.
The one thing that's nice about the suction cup tool is you can reach across from the
other side.
So you can reach across the device here and you can just kind of take the pressure off
a little bit as you come up.
And once we get close to the top here, let's go ahead and remove our tool.
Now having this pick in here allows us to be able to hold this up and just gently pick
up.
I would say just be very careful and don't rush anything and just keep applying heat.
There's nothing really that gets damaged if you apply too much heat as long as you stay
along the edge here.
But just try not to do too much, but you almost have to do more than what you think you should.
This is some really strong adhesive.
So you want to just keep working it all the way around.
Then once the adhesive lets go, you can just pry it right up.
Some of this adhesive will come off, but it's okay because we're going to apply new adhesive.
So the back cover comes off just like that.
So next what you will want to do is grab a Phillips screwdriver size 000.
And so we're going to remove all these Phillips screws all the way around the perimeter here.
We're going to remove all those 13 screws.
So next after removing all those 13 screws, and don't worry, they're all the same size.
You don't have to worry about keeping them in the right order.
Then what we're going to do is we're going to just grab a plastic pry tool.
Start somewheres in this notch right in here.
Just slide over.
There's adhesive under this part here.
Just kind of wiggle it all the way around in this corner as well, and the QI charging
pad releases.
And you're just going to want to let it flop like that for now.
Then what we're going to want to do is remove this metal frame all the way around here.
So what I've found is if you start close to the top, and you can just kind of get your
fingernails in here, in this edge, it wants to start separating there.
So you can just get your fingernail in there, and then you can just pry up carefully.
Let the bottom to last, and then this whole part comes out just like this.
So next what we will want to do is remove some different connectors.
So using a plastic pry tool like this or your fingernails or something, go ahead and remove
this connector right here.
Let's go ahead and remove this connector right here.
Remove this connector here for the earpiece speaker.
Remove this connector over here.
Then you'll also want to take a tweezers and remove these antenna wires right here just
by prying up on them a little bit.
The next what you want to do is pry up somewheres, and the front camera will stay right in as
you pry up.
The motherboard logic board will be very loose by now.
So we can just carefully tip it up, and then we want to remove this connector right here.
The logic board comes out just like that.
So next use a hair dryer or a heat gun or something, and we're going to want to heat
this battery up.
Not too hot, but you're going to want to heat it up some.
We don't want to do any damage to the screen, and it's glued in here so tightly that you
could crack the screen if you don't have some heat in it to pry it to start with.
So after giving it some heat, what you're going to want to do is have something really
thin and not sharp that you can pry underneath it.
And you're just going to want to start right here and just keep working your way in a little
bit.
Now if it seems like it's going too hard, give it some more heat.
Make sure not to puncture the battery.
Now what I would recommend is after you have a little gap, pry with something like this
that's a little bit thicker.
We can move this back down to the center of the frame more.
Then it sounds like it just let loose.
Carefully pry up.
If it doesn't want to go yet, we'll give it a little more heat.
Carefully cut the adhesive with our little tool, and the whole battery comes off just
like that.
To reinstall the battery, just grab your battery.
If it's a new battery, make sure to peel the adhesive film strips off the back.
Also if it's a new battery, you'll want to probably transfer your serial number off onto
the new battery.
You can just peel it off and stick it onto the new battery if you want.
So grab your battery, set it right down in here, press it down.
To reinstall the logic board, set the logic board here.
You're going to want to bring this connector up, reconnect this connector to the logic
board.
Make sure that it's connected properly.
Set this down.
Now watch for all the different connectors.
I'm going to use the tweezers here just so you can see easier.
And watch this connector and this one, the earpiece speaker, make sure the front camera
sits down properly.
Let's start reconnecting this connector right here.
Reconnect this one right here.
Make sure the front camera is sitting down properly.
Reconnect the earpiece speaker, and reconnect this connector right here.
Now we're going to want to reconnect these antenna wires right here.
It can be a little tricky to get lined up, but just make sure that you don't push down
until they're completely flat, then you can push them right down in.
But they have to be perfectly flat in order to go on there without binding or whatever,
and then they'll click right in.
So make sure they're both in their channels where they're supposed to be, on this side
and on this side.
Then we'll want to go over the connectors one more time.
Make sure that this connector is connected.
This one here for the front camera, this one here for the earpiece speaker, and this one
over here.
Make sure they're all connected, and then we're all set.
Next we'll want to grab this part right here, set it right down on here.
We'll want to get the bottom started first, and then just keep pressing it in.
Check it to make sure that it's in all the way around.
Go ahead and put all your 13 screws back in.
Next we'll want to make sure that the Qi charging pad is stuck down where it belongs.
You pretty much see right where it goes.
Just go ahead and stick it down on top of the battery.
I would recommend putting new adhesive on the back before you reassemble, otherwise
it won't stay on there tight, your back cover.
And I'll have links in the video description where you can find the adhesive.
So once you have your double-sided adhesive installed all the way around, now to reuse
your back cover, I would recommend getting as much of this excess adhesive off the back
before you start reassembling.
And once you have your back cover cleaned, go ahead and just set the back cover down.
Start at the top.
Try to get it to set down in all the way around.
You can just press down, and if you want you can apply some heat around here just to make
sure it sets down.
Reinstall your SIM card tray, power on your device, and you're all set.
Thanks for watching.
