How To Set Posts To Build A Pole Barn Yourself DIY

Finger Family
30 followers
3 Video Views·Oct 28, 2022
"How to set posts to build a pole barn all by yourself. How to install and set 6x6 treated posts for a pole barn all by yourself DIY. This is the best way I’ve found set pole barn posts all by yourself. With a few of the right tools and the right system and a strong back it’s very doable. :)
In this video I don’t show how to lay out your pole barn and setting up your strings etc. but I do show how to set the posts. I will cover the rest in another video and link to it once it’s complete"
Hey guys this is Paul from Smart Easy DIY. Today I wanted to show you how I set posts for a pole barn
all by myself and how you can too if you follow the methods that I use. Now I have to warn you
this is a little bit of a lengthy video but if you watch it all the way through hopefully it'll
help you and give you ideas how you can set posts by yourself. So then before you get all set up and
put the posts in the hole like I'm doing here, first thing you want to do is make sure that
your hole is going to work. So I set a string up, stretch it really nice and tight along whatever
side I'm setting and you want to check your post hole make sure that it's going to work.
Make sure you have room in there to put your post right where it needs to go for center.
And in my case the posts are 10 foot on center. That's how I measure off the last post to see
for sure if it's going to work. And I use like three-quarter crutch gravel like that.
In the bottom I pack it down in the hole very good with a plate tamper. Just pack it down really well
and then that'll hold it good when it's getting ready for concrete. What I do is I get 10 foot
two by fours and they usually run a little bit longer than 10 foot. So I'll mark them out but
I'll show you here. See as you can see there they're about a quarter inch longer. So I make
one end perfectly even with the center of the post, the previous post. Like this I'm showing you here
and then I just overlap it a little bit and then I run one under and one over as I'm going down
through there. So first thing I do is get a screw in that end to get it ready and then I prep this
other end over here with another screw. As you can see I stay in from the end a little and then
I make a mark measuring from the other end right on 10 foot with that. And then I get my setup here
got some screws, screw gun level, tape measure. Then I got this two by here that's for my prop two by
that's actually the first two by that I put on when I bring the post over. So you want to stay
back from the end there and put a screw in that. Don't put any on the other end just let that be
how it is. Just have that ready to go and you can see how I brace those all on the inside those
other posts going down the row there. That's all I'm going to do here once I'm all done. So the
idea is just to have that ready temporarily hold the post up for me. So then if your string is all
ready and everything then you're all set ready to set your post. Now the corner posts are a little
bit of a tricky thing. You have to get them set first. I'm just showing you some posts and down
the row here because it's easier for me to show it that way. But the corner post is the trickiest
because you've got to get a perfect brace both ways. You can see that one is braced inside and
out the other one's braced to the outside one away it's just because of getting the cement truck
in there that was the easiest way for me to brace it. So you have to think about getting cement in
there and that'll determine how you brace it what direction. So just get the post in the hole there
try not to knock any dirt in if at all possible you usually get a little bit. Then what I do is
just grab the post pick it up a few times make sure it's settled down really good. You just kind
of eyeball it and get as close to the string as you can. So of course you can't let go of the post
there as you can see because it just wants to fall over. And so the next thing I have a screw gun
with a belt clip on it that helps it really nice it can hang on my pants then that way I don't have
to reach down and grab it afterwards. So then what I do is I just put a screw in by hand screw it in
a little bit that way I don't have to hold it and then the screw gun can just drive it on in.
And all this screw is for is to hold the brace so it doesn't fall down as I'm fastening it. You can
see it's a little bit tricky this is when you get your hands really full. So then that brace there
since I already have a screw started in it I just screw it right into that post and that screw I put
in before just holds it from falling like I said. And then that 2x works really good for twisting it
to make it square with the string and stuff and just kind of gives you a lot more control of the
post. And then that just jammed into the ground like that on the other end that actually holds
that post really pretty well. If it doesn't you can always go back and push it a little bit but
now you've got a lot more control over the post that you did to start with. So then here's where
you really need about five hands but it's doable to do it by yourself. I've done it many times so
that's what I'm showing you. So that's where it's nice where you can just set your 2x back there on
top of the previous one so that holds that end. If you're doing it underneath you can put a screw
under there about four inches under that last 2x and then that'll be your support if you're
underneath there. So then the only reason I use a level for this is because I like to have it pretty
much level. It's not critical but that way your measurement is a lot closer to being accurate
your 10 foot spacing measurement. So then I just put that baby right on the mark and screw it in
right there and then you can see the post moved a little bit when I pushed back on it but that
brace holds it pretty well. And now that that's fastened you just kind of check it again to make
sure it's pretty square. That kind of holds it but it might be a good idea to hang onto that 2x as
you're walking over to the other side. And then you can just put that right in the center there
and screw it in. Then when you're all done of course you recheck that measurement but now you
just go back over and that thing is held pretty well. So then here's now where you can have your
bar handy and you can pry it back and forth. You can kind of tell pretty easily looking at it which
way it's got to go but you can check with the level then too. But that's where you start prying
off the edge and then you just start checking it and you repeat this process quite a few times.
Just take it a little bit at a time then you measure to make sure that your mark is dead on
and in my case it was right on. I measured back from the end of the building too just to confirm
it. Then use that brace post there that I used that brace 2x and use that to twist it straight.
You want to make sure it's nice and square with the string so you can move it around with that
because you got lots of leverage. And then what I'm saying here is today is my birthday by the way
when I'm setting this is August. So it was my birthday and what better thing to do than to set
posts on your birthday. But anyway so yeah you just check it a number of times. Check it for in
and out. Check it for sideways. Then you just use the bar and pry it a little bit at a time till you
get it where you want it. And if you take it a little too far you know there's no shame in that
you just take it back a little bit. Then when you got it good I like to put a 2x down there just
keep it up off a little because you don't want to move it again when the cement truck comes. You
want to have a little room to work. So I put that 2x on there and then that braces it really well
for that weight. Then for this weight once you make sure that it's square then you pound a stake
in like that and then you can come back and double check it. And then if you get it right against the
string where you want it and it's level then what I do is I hold it put tension on it and then I
drive a screw through the stake down there and hopefully it holds it right where it was. So it's
a little trial and error when you're doing it by yourself you got to come back and check it a few
times. Double check it a few times. If you have to you can take this loose on the top part here
and then I would recommend taking the screw right out and starting a new hole because if you only
got to go a little bit it'll want to put it right back in the same hole and it won't want to move.
Then I use a clamp like that and it works really good to hold that level on there. I could do this
from the start but it's just something that I learned. That way it's kind of hands-free you
can keep the level there and then once you're all ready then you just want to put another two
by on the bottom like that to brace it really good. Most people don't do this but I like to do
it just because when you pour cement in there you don't want that thing to move at all. So anyways
all right well I hope this video was helpful. If it was give it a thumbs up and let me know how
you did setting your own posts and maybe give me some of your ideas too and thanks for watching guys.
