ALEXA Smart Mirror (New Build)

Ose 9
46 followers
7 Video Views·Oct 27, 2022
Now the mirror I'm using is an 18 by 24 inch mirror. Here are the dimensions of the wood
with some 45 angle cuts. Here you can see what it looks like roughly laid out. Now I'm going to add
some glue to the corners and square it to make sure everything fits properly. I'm going to put
in some support nails on the corners. This will increase the strength of the structure.
Next I made an inside frame to hold the mirror in place on top of the front frame.
Again I added some glue and nails to this as well. Here are the frames. Here I measure an inch and a
half down so that the inside frame is level with the outside frame. Add some glue to the bottom
and now we'll stick it on the front frame lining it up with that line I made previous.
Clean off any excess glue on the inside. Now I didn't have any clamps to put these together
so I just used some extra weight on the frame and left it overnight. Here's what it looks like
after. Now we're going to put the mirror in to make sure it fits. Looks good. Now here are the
main components going to be in it. A raspberry pi. You got your monitor. Here we have the
hdmi control panel, the lcd screen, and the backlight. There's your hdmi that adjusts the
brightness of the monitor and that fits perfectly in the corner. I'm also going to be using some
heat sinks on the raspberry pi. Because the software can be processor dependent, this will
allow for the heat to dissipate a lot more efficiently. Next we have the material that's
going to take up the rest of the mirror. As you can see, no light can shine through this. I'm going
to trace it out and cut it out based on the mirror dimensions. Now I'll show you how this works.
Here you can see it is see-through completely. You can see my hand. Now if we add this to it,
it looks just like a normal mirror. No see-through. So now we're going to do a rough
installation to see how it looks. Now I wanted the frame to match the rest of my furniture,
so I stained it a dark brown espresso color. It looked nice up against my wall and in comparison
to my other furniture. Next I drilled a few holes for ventilation. Again, let's put it back together.
Now here I have some support screws that go into the frame
and some little hinges on the edge. Now let's add the indicator LED lights. I have to drill
through the frame a little bit in order to get the wires through the outside to the inside.
That's okay. Now all I have to do is stick it and feed the wire through. Here you can see them
working with the raspberry pi plugged into the raspberry pi. And here's the circuit that you're
going to be using. Here's an n-channel mosfet connected to the raspberry pi and some LED lights.
Here I got a stickable breadboard which made it easier to just plug it in. Next to turn the mirror
on and off, I'm going to be using a sonoff switch. It's basically just screw terminals that connect
to my extension cord. So here I stripped some of the extension cord. White is neutral, black is the
line, and green is your ground. All we need is ground and lines. Then I snipped those and stripped
the ends. Now I can feed it into the sonoff switch. L for line, N for neutral. Next we're going to go
on to the Amazon Alexa app. I'm going to go to smart home devices and connect to it. Sync it in
as a device. Next I'm going to go to routines and I'm going to set up a routine so that it turns on
at a certain time during the day. Now I wake up around 7 30 so I figured I'd have it up set up to
turn on at 7. So by the time I wake up it's already on. You can repeat this whenever you want.
And you can actually have it read the news or weather. So I'm going to have it read the weather
when it turns on as well. Now that that's all set, we can install it into the mirror frame.
Here's an old webcam I was using that had a microphone on it that I could use to talk with
Alexa. Now I'm going to unplug this for a second, feed it through one of my holes, and re-plug it in
so it's on the outside frame of the mirror. Now the remaining parts to this build are going to be
a 5 volt power supply, a 12 volt power supply with a splitter, and an HDMI. Here you can see
me plugging everything together and screwing it all in place. Because this looks confusing,
here's a basic layout that I drew up for you guys of what I did. Now let's go and hang it up on the
wall. I just put two screws to go in the inside. Now I kind of fed the wire back behind my bureau
so it's hidden and put the Bose speaker in front of it. And here it is booting up. And you're all
set. Alexa, resume music. That's it. I hope you enjoyed the video. If you just plan on using the
Pi with the monitor, it's a lot simpler. All you need is the Pi, monitor, power supply, and HDMI.
I'm releasing a software video for this build very soon. As far as the setup goes, I could have
honestly crunched it into a 3 minute video. It's pretty simple. But I go over some aspects of the
setup that I think are important when you bring your build a step further. So let me know if you
want to see anything else in the comments below and I will read through them as they come in.
Give this video a like and subscribe if you enjoyed it. And if not, give me a thumbs down.
I will continue to improve on these projects and upload more like this in the future.
