Micro Camper Overland Build | Part 3 | Body Construction

Travel Vlog TV
137 followers
23 Video Views·Oct 25, 2022
What's up guys welcome back to the channel. Today we're on part three of the micro camper build
and we're going to work on starting the actual body of the camper. Previous videos we did the
frame then we wired up all the lights got the suspension all set up so if you haven't seen
those videos go check those out lots of useful information there. As always going to give you
a rundown of where we're headed here. As you can see those panels on the left side of the screen
those are going to be the structure that we're going to build out of our square tubing itself
and then in the end we'll end up looking more like what you see on the right here.
The metal tubing we're using is three quarter inch by three quarter inch 16th wall which I
believe is 16 gauge. It only weighs about 0.6 pounds per foot so it's super light but it's
still steel so it's strong and plus when you have it all tied together like we're planning on doing
I think it'll make for a very very sturdy structure. Our outside walls we're going to be
doing an aluminum composite panel this is three millimeters thick it's basically a very thin
piece of aluminum composite paneling and then another thin piece of aluminum and you can get
it in different colors this is in white this is just a protective film that's on it so this is
what we're going to be attaching to our body to create our exterior look and I think it'll be a
nice professional finish. As you can see here I've planned out my cuts that I'm going to make on
these pieces of metal so each one is labeled for what wall they're going to feed the long line on
the bottom is size that the piece of metal came in and then all the little dashes above it are the
I'm going to be making and on this app on draft paper you can actually sit there and take a ruler
and measure the cuts you've already made so you can plan ahead know exactly what kind of cuts you're
going to do and how you're going to do them and it just makes things very simple when you're
dealing with a lot of little cuts like this. What we're going to be doing to cut our little three
quarter inch by three quarter inch steel tube is a Diablo steel demon blade this thing cuts
through this stuff like butter it's not supposed to be run on a miter saw with this high rpms
but I think it'll last me long enough to get this project done it's meant to be run on a dry chop
saw so beware you're going to pay like forty dollars for this blade and if you do not have
the right chop saw may not last as long as you'd like but I think it's going to last just long
enough for this build which is kind of all I care about. It cuts super clean super quick super easy
and with a miter saw I can set all my angles and get all my angles cut nice and simple save a lot
of time versus the bandsaw. Just be warned when you're using the steel demon blade cutting steel
it is going to throw quite a bit of metal chips as you can see I ended up putting my welding
helmet on just because I really didn't want to get a piece of steel in my eyes. The outline of
each wall consists of six pieces three of them are identical to each other so what you see me doing
here is taking a piece that I've already cut and I want to reproduce that piece exactly to keep
everything nice and square so I'll lay the piece on top of it line it up with my saw make sure it's
going to cut at the exact same length and then remove the piece clamp it down and cut it. Alright
guys here's our pieces that you saw all cut out and laid out and the shape that they're going to
be laying so this is the front of the trailer that's the back of the trailer we will be around
right here somewhere so you're going to need two pieces these are seven foot long right here
there's a 45 degree cut right there and a 22 and a half degree cut there two of those and then these
are three foot and three foot and that's going to be 45 degree cut there and a 22 and a half degree
cut there our little end pieces that we have here are 17 inches overall length and they have 22 and
a half degree cuts on both sides and we do 22 and a half degree cuts because when they butt together
we get a 45 degree angle so hopefully that's easy to follow and easy for you to understand why I
chose the angles that I did. With our pieces cut now I'm working on removing the mill scale so we
can prepare for welding what I'm using is a Craftsman Restorer and it's the paint and rust
remover wheel is by far the most efficient way that I've found to remove mill scale get it ready
for paint welding or anything else you want to do with the steel. Alright guys we got all of our
pieces cut for both sides all I've done here is just laid them directly on top of each other
because for this trailer to look right you're going to need both sides to be exactly the same
for that reason we are going to tack them up while they're kind of stenciled out on each other I'm
going to go ahead and use the fireball tool square that I used in part one and basically
this is just going to verify this is a 45 degree it's going to help me level it out on this plane
and then also make sure my angles are correct so basically now that they land on top of each other
I'm going to tack this up move on to my next joint tack it up so on and so forth all the way around
if you've seen my previous videos you will know this is the first build that I've used
this fireball tool square and I gotta say that it truly helped me get this trailer square and
have it turn out exactly like I envisioned all right guys well here's the walls I just have it
clamped to the trailer to kind of mock it up so you can get a idea of the shape of it and I'm
really happy with the size of it and how it's looking so far what I'm working on next is this
is going to be our door I'm going to be mounting that on the driver's side of the trailer so
basically what I've done is trace that out a piece of cardboard and this stencil is going to kind of
help me figure out where I need to place these other bars because that door has to actually
screw to that on the sides and top bottom figuring out these bars right here and then I'll
have to add some horizontal ones as well that'll be how we mount the doors window over here and
the window over here frame our door up here we got that one front piece you saw closest to the
front of the trailer and then also the one that was a little bit further back from it and basically
we just set the door on its face put both of those pieces on each side measured how long our pieces
are going to be here ended up being 27 inches and then of course I had to cut this a little bit
because it was going to interfere with that part of the trailer how it angles up so now pretty much
all we're going to do is take our pieces of metal and get them all in there and tack them all into
place and that'll be about as simple as it is to mount our door go ahead and ensure your door
frames all nice and square that way it fits well when you go to place it on the trailer
so just like we did with our door I made a stencil with our window here and I just kind of kind of
propped up figuring out how high I want it and what position I want it on the trailer this way
I think I'm just going to go ahead and match it with the top of the door so it's nice and even
and then after that I'm going to build this frame basically I'm going to do the same thing that I
did with the door build a frame on the floor here using my window to help me get it to just the
right size and once this is tacked up I'll bring it up to the wall there and get that all tacked
in place and then we'll move on and do the other side one thing my dad has always taught me growing
up is that you can almost do two sides as fast as you can do one so while you're in that mindset
and got all the tools right in front of you go ahead and build both your windows at the same
time and plus you can ensure that they are the exact same shape and size if you've already done
any sort of fabrication you could probably already catch on to the fact of how useful
these magnets are they really help me make sure that the surfaces are flush and hold things in
place when you don't have that extra hand to hold something while you tack it here we are adding the
rest of our vertical supports these are going to be 46 and a half inches each all right guys really
starting it looks like something here you got the walls coming all together your window our door
our other window lots of support for the roof and I also made it so right here at this joint
this pole lands on that so then this is all going to be tied together here just to kind of further
solidify this but if you have anything on the roof here not kind of bending on that connection
right there all right guys with these sidewalls all done we're going to start working on connecting
them this way basically I just got this one wall set up here magnet to keep it flush for the edge
some clamps to hold it you can see the level it's 89.8.9 it's pretty much 90 degrees I mean that's
close enough for me all I'm going to do is just kind of put a couple tacks all along this we got
our surfaces painted all the ones that are going to be against each other so there's no bare metal
left we're going to tack it up in a few places move all this stuff over the other side tack it
up and then we're going to start adding our our bars across this way all right so I just quickly
ran around and tacked in those walls and then we're going to go ahead and start cutting our
horizontal bars which are going to be 55 and 1 8th of an inch we are going to do four of those and
just like we've done in the past once you cut your first one use it as a stencil to cut your next ones
so you can lay it on top of the metal you're about to cut line it up with the blade make sure that
it's the exact same length before you cut because these being the same length will determine how
straight your walls are all right guys we got our bottom bars tacked in here I'm going to show you
what I did with this rear one it's different than the front so because our aluminum composite sheet
is going to have to stick to this surface I actually welded this one in at an angle so that
way it gives us a bottom surface to actually stick the sheet to so now that this is all tied
together feel pretty comfortable that it's not going to end up warping a bunch on me so I'm going
to take my time go around and start welding up all these things that I just have tacked and I'm also
going to add these gussets here and I'm going to add those first before I start welding basically
I'm going to put some gussets here in this corner some this corner basically like two on each corner
of the trailer top and bottom and that'll really help solidify things before the finish weld if
you're not sure where to add the gussets I'm basically adding them in places that it's going
to have lateral load so basically any pushes on left or right of the trailer this will keep the
frame nice and solid all righty we got some gussets added to all of our main corners here
we've got some up top really kind of solidify the whole structure of the trailer itself
come on these top corners there and there and then down here as well and of course I'm still
going to be adding some lateral supports here more verticals and stuff like that so it's just
going to get even stronger than this so the walls all fully welded in and the main structure kind
of set we are going to work on the roof next and in our roof we're going to have a spot for a vent
fan it's actually a max air fan and because this bar is already there and these two bars already
there we're just going to have to cut four more 55 and a quarter inch bars to match the ones we
already have in there and then we'll end up adding some side supports as well which is what our fan
will mount to but we'll get into that in a minute just like we did with our windows and doors we're
using the fan as a stencil to create our frame for it and then once our frame is created we
can actually put it up in the roof and weld it in here I use the combination of clamps and magnets
to be my extra hands to get these bars welded in the roof it could be a little tricky but with
some patience it's definitely doable by yourself all right guys you may have noticed that I have
not done the front or back wall yet and that's because we got to get our floor in there first
but before we can do that we got to go ahead and get all this all finished weld in I'm doing that
just so the sparks and stuff from the welder don't end up burning the floor it's plus it's a whole
lot easier to walk around in there right now without the floor so we're gonna go ahead and
get it all finished welded in the floor onto the trailer and then after that we can close in the
front and back walls I wasn't exactly sure how many welds I was gonna need so I kind of just
went around and probably did more than I needed guys I went along I pretty much just welded the
camper body to the frame where all the supports are did some in the rear did some in the front
here and then I went around with the grinder and smoothed out all my walls on both sides everywhere
that I have to put one of these aluminum composite panels because I need it to be a flush surface
for the adhesive so now I got a little bit of surface rust on this bare metal because it's
been sitting out so now I'm going to run around with my craft center store with the paint and
rust remover wheel this is what I've been using to clean my metal this whole time and clean off
any other little bit of surface rust that has formed on this then we're going to go ahead and
start to paint this part of the frame because we're using steel it we'll still be able to weld
in our crossbevers later one good little trick for using spray paint is using a piece of cardboard
as kind of like a barrier so if you are spraying something you don't want to get paint
on whatever is behind what you're spraying you can kind of use it as a shield
all righty all of our present structure is all coated with paint next up we're going to work
on getting this floor down first thing we're going to do is run around with this stuff
called Sikaflex 221 basically it's just kind of like a caulk but it's going to multi-purpose
and where we're going to put this stuff is all along these edges all the way around so
those little inside edges we were welding to secure the body to the frame we're going to go
ahead and seal all those gaps around that way no water can seep through the sides and intrude
into our floor pan here this stuff does come in different colors such as black or gray it didn't
really matter for me because you're not going to be able to see any of the surfaces that I'm going
to be sealing this stuff does dry very well and hardens up real nice it's not like your regular
bathroom silicone you may be familiar with with household work this stuff is really heavy duty
what we're going to be using for the floor is this aluminum composite sheet it's three
millimeters thick it's basically a small piece of aluminum and another small piece of aluminum
and in between it is sandwiched some composite material like a plastic and it's actually really
strong and pretty lightweight for what it is the size we're going to need for our floor is 81 and
three quarters of an inch long and 54 and a half inches wide so we're going to go ahead and get
this cut out this is actually a five by ten sheet so they come in five by ten and also four by eight
all i'm using is my circular saw and the blade i have on there is actually a fine finish wood blade
so it's got a high tooth count with our floor all cut out now we're going to move on to what we're
going to use to attach it so it sounds crazy but we're actually going to be using this 3m vhb tape
it's a double-sided it's very very strong adhesive i used it on my very first trailer
build if you've been following along that long to hold my fenders on didn't have to put your
rivets or anything in them and those fenders haven't moved at all plenty of videos online
showing the strength of this stuff i completely trust it so that's what i'm going to use to secure
these panels to the camber and of course the corners are going to get encapsulated in with
the trim which will also help but even if i didn't have that trim on there these panels aren't going
anywhere with this stuff so i'm going to be using the inch this is actually a roll i have left over
using the inch thick on these thicker beams and stuff like that in the center and then i'm going
to use a half inch roll to do my edges and then i will be using half inch for the whole rest of
the trailer as well you can go on amazon and get a whole bunch of it in bulk which saves you some
money versus buying them separately it's a little expensive but it's 100 worth it after going around
and making sure all my surfaces are free of debris i'm going around and laying down this tape the red
coating you see is nice because it keeps the adhesive protected until you're ready for it to
be stuck to something after getting it laid down in all the places that i'm going to need it went
ahead and peeled up the adhesive and then we can start setting our floor in place all right guys
the floors are all in i'm not going to lie trying to set that with one person was really tricky and
i ended up not getting it set perfectly like i wanted it to it's a little further back but that's
okay all the edges are still sealed now i'm pretty much going to take some of that secaflex
and i am just going to just i'm just going to lay it down all the way around this whole thing
just to ensure that we're not going to leak later but uh this floor is now permanently bonded later
on we're going to end up doing some insulation and some other flooring over top of this so you
won't ever see any of this stuff ever again alrighty i did the secaflex all the way around
in the end i ended up using probably an entire tube and then some on this lower half just because
i really don't want water to be able to leak in between the frame and the body so now that that's
setting up we're going to start working on our walls here because the only reason i did that
first before i put the walls up was because it was a little easier to get it in there
now that that's in we can finish out our front and our rear walls basically all we're going to do
is cut two 55 inch wide pieces for the front and the back we have them up here on the top because
that is where we have our angle that angles back in the front and then comes up from the back so
we're going to go ahead and get those cut weld those in and then we're going to measure for the other
pieces just like we did for our rear lower bar i'm welding it in at an angle so our aluminum composite
sheet has something to stick to we're doing this for this front bar and then also the rear bar next
up we're going to run some supports from that front bar up to our roof and these are going to
be 15 5 8 of an inch long these next bars are going to be 35 inches long at the longest point
and the top side is going to have a 45 degree angle cut in them that way it can conform to
the angled bar that we welded in in the middle there the rear wall of the camper is just rinse
and repeat of the front all the same measurements it's just upside down all right that's all of our
walls welded in and also painted so now we got no more bare metal nothing to rust up on us
got the floor all in next step i think i'm going to do some more aluminum composite paneling and
i think i'm going to go ahead and get the roof on while i have access to getting underneath the bed
kind of make it easier all right guys first thing we're going to do is cut our aluminum composite
sheet to fit our roof so basically we need exactly seven feet which is 84 inches so all i've done
is you can see i got that line there that's right at 84 inches and i'm using a scrap piece
of the aluminum composite from the previous cut as a fence so basically i'm just going to take
a skill saw and it's just got a high tooth count blade it's the same thing i cut aluminum with any
high tooth count blade will cut this stuff this stuff's actually pretty soft so we're going to
use that as a fence so we get a nice straight cut we'll go ahead and use our saw cut that and then
we'll work on getting it fitted to the roof with our top sheet cut what i've done is i've laid it
up here and i'm just kind of fitting it up making sure everything looks good i know there's extra
over here but i'm going to show you what i end up doing is once this is stuck i got a router i'm
going to use and the router has a little roller that will roll against this so that i can cut it
perfectly flush all the way around this whole thing there won't be any crazy gaps or anything
like that so as you can see the back is already flush this side will need a little bit of trimming
and that side but it'll be nice and easy with the router and then it'll be a perfect fit for
that top part of the roof same process as the floor go ahead and make sure your surfaces are
clean and then lay down your vhb tape in preparation for sticking the roof where their
tape stuck to the top edge i left the red surface on there so it's not sticky yet went ahead and
positioned it exactly where it's going to be and the easiest way i'm thinking to do this i've clamped
one end so because of this stuff is flexible i'll be able to lift this up start peeling the red
surface off which will allow it to be sticky so once i peel some of that off i can stick this side
and then just kind of work my way down this way instead of just trying to peel it off and then set
it down there perfectly which would not be possible i don't even think with two people
but i think this is going to work out pretty good so we'll see how it turns out this method turned
out to work very well and i actually also used some scrap 2x4 to help hold up the aluminum
composite sheet while i was peeling all the protective coating off the vhb tape itself
with the ceiling all stuck i ran around with the router and cut all my edges nice and flush with
the frame here we go we got the roof all on nice and solid with that vhb tape as you hear there's
no rattling no buzzing sounds like it's part of the trailer that's because it is that's just
permanent bond later on we'll have to cut out the hole for the roof vent not worried about that at
the moment all right i decided we're going to do this sidewall first so this is a four by eight
sheet so it's already the perfect height for this which is another reason why i made this four feet
so to make things a little simpler and of course we have an eight foot total thing so all we're
going to have to end up doing is chopping off a corner here and a corner here once it gets stuck
up there so what we're going to do is go ahead and put the vhb tape on our frame here and thankfully
our little outriggers here will actually support that so then all we got to do is pick this up
set it in place and then lay it flat against the wall and stick it to the tape so it'll be much
simpler than the roof was and then we will just repeat the same process for the other side at this
point in the build it's really starting to feel like things are moving along nice and quickly
now that most of the fabrication is done sticking these walls on is really not as maybe difficult as
i imagined i will also say that putting on a panel that is larger than you need and then using the
router to cut to fit is the way to go because when you're dealing with this vhb tape if you cut out a
perfectly sized panel you may accidentally start sticking it in the wrong spot on one side because
it's such a large piece and the next thing you know your panel's crooked on your wall
and there you've wasted a bunch of vhb tape and possibly the whole panel moving on to cutting the
holes for our doors and windows what i did for the door was just use a cardboard stencil that was
the size of the part of the door that had to insert into the wall so this is a little bit
smaller than the stencil we always use them to mock it up and it made it super easy to cut the
right hole by just putting it up there tracing it out and then i ended up figuring out the angle
grinder that finished off with the leatherman and the little handsaw was the best way to get
these holes cut all righty guys we got all of our holes cut i think the main thing to take note of
on this step is see i didn't use the router because we needed to leave those corners there
if we didn't leave those little rounded corners then actually the window wouldn't fill it out
and there'd be a huge hole up there in the corner so that's just something to take note of yes the
frame of it is a square but it's gonna have to be rounded on the corners for everything to seal
upright i actually ran out of vhb tape which is why the front and rear walls are not done yet
i ended up working out pretty nice i had nice airflow through here while i was working on the
windows and the door opening i think next i'm gonna go ahead and mount the door up and then
after that i'm gonna look at mounting the windows the windows might have to last after the interior
is done just because of the way it sandwiches together but we'll just have to see maybe i can
temporarily install them securing the door was a lot easier than i anticipated basically just put
some beetle tape all around the edges and then there's some holes and some provided self-tapping
screws so we put the door up in its spot make sure it looks level and then use the self-tapping
screws to secure it to the steel frame that we made around it and while i was at it went ahead
and took the router and cut out the hole in our roof for a vent fan alrighty so that's the
installation of the door as you saw i put some beetle tape all around the edges here which is
supplied with the kit you can get the installation kit with the door and that is what's going to
give us our weather seal and then they give us some self-tapping screws which basically those
screws screwed into the metal frame that i made around the door so that's how that's
mounted right now it's not clamped by anything there is another ring on the inside that we'll
put on once we get the interior done but for now the door is mounted and functional
and next we're going to get to working on putting this roof in it pulled back the protective coating
on the aluminum composite sheet since we're going to be sealing these edges with some caulk in the
end all i did was take a sharpie and mark where each of my corners are going to be and that's
really going to help me center it up so then our screws that are going to go in over these little
dots on the outside so it'll help it all line up nice and easy this is what our butyl tape looks
like comes in a big roll like that yeah basically so you just want to have it nice and consistent
all the way around and as you screw this down you're going to have some bleed out that you
might have to trim with a razor blade but that's all good that just means it's sealed up nice so
now that we got this sitting on the fan we're going to go ahead and place it up there on the
roof and get it screwed down to the frame this butyl tape is really sticky stuff that's why i
wanted to mark my corners and make sure i was putting it in the correct spot the very first
time so i didn't have to pull it back up and try to readjust there's a lot of little screw holes
around this whole vent and i assume they do that just to make sure you're not going to have any
leaks so i'd suggest go ahead and using them all all right here's the max air vent fan all screwed
down and i used some more of that sika flex on the edges even though the butyl tape was there
so that thing should be extremely watertight shouldn't have to worry about it leaking on me
which is the last thing i want then next i'm going to run around with the vacuum
clean some of this stuff up i still have the protective coating on the floor you probably
clean this up and then i'm going to take some more of that sika flex and run beads all along
this bottom edge just to further solidify and water is going to be able to come up under the
wall there all right guys i didn't show it because it was a lot of uh boring stuff but basically i
went around with the sika flex and did all these outside seams anywhere that water could possibly
intrude if it gets past the outer seal and my vhb tape finally came in so i'm about to put these
front and back walls on and then after that i think we're going to wrap the video up i'm going
to go ahead and get our vhb tape on the rear wall and then we're also going to go ahead and put it
on the front while we're in the mode of sticking tape just make sure these surfaces are nice and
clean when you're applying them just like we have before the piece we're going to use to stick to
this front wall is going to be about 35 inches tall and it's going to be a little wider than
the trailer but we're not too worried about the width we can trim that with the router but our
height has to be just right because we will not be able to router the top or bottom edge once it's
stuck up there on the back side the height does not matter because we'll build a router along that
top edge what i've used is just some clamps on that lower bar and that will act as a resting point
for my panel so then i could just rest it right there on those clamps and it'll be in the perfect
position to still allow me to put on my lower panel so that's the front and back walls on
obviously these are still hanging off we're going to trim these with the router once we get the rest
of the wall on so next i have to actually cut and measure this one to actually fit just right
so it's going to be 17 inches so basically just a 17 inch wide piece and of course we'll have
some overhang but we're going to clean that all up with the router after it is stuck up there
before actually sticking the piece on i always like to do a dry fit with the adhesive not exposed
just to double check which way it fits best or how it's going to fit before i commit to it
then to finish it off we just go ahead and route our excess off the front and back of the trailer
guys i think that's where we're going to wrap this video up we got all of our panels on here
on the front and on the rear and it's really starting to look like it's coming together
all right guys as always thanks so much for watching don't forget to leave a comment let
me know what you think hit the thumbs up and subscribe if you aren't already
and we'll see you on part four
