DIY Pantry Makeover | Home With Stefani

A New Strategy
79 followers
17 Video Views·Oct 24, 2022
Hey, it's Stephanie. I hope you're doing well. Today I'm so so excited to share with you guys
my pantry makeover project. We started off with some basic wire racks and they started separating
from the wall and we would lose stuff in the grates and we had to place certain items just
right or they would wobble or fall over. Not very practical so I decided to take all the wire racks
out and make some nice sturdy custom shelving. I also added these cabinets. So these are basic
upper kitchen cabinets from Home Depot. I made a little base out of two by fours for the cabinets
to sit on and then finished it off with some nice trim. These will be perfect for storing some of
our smaller kitchen appliances and other kitchen items that we don't use very often. I also left
the corner space open so we can put our recycling bin there and any extra drinks or containers that
we have. There's a lot of ways you can customize this design. If you missed it, I posted a video on
how I planned and designed my entire pantry project in Sketchup so I'll share the link to that video
in the description below if you're interested in watching that. My next video will be all about
organizing the pantry. I'm going to DIY some fun organizers and I also bought some food storage
containers to help us stay organized. So stay tuned for that video. For this project, I will link all
the tools that I used in the description below. I'll also share a blog post with all of my pantry
dimensions and I'll do a cost breakdown for this project as well. Anyways, I hope you guys enjoy
this project. This one has been so much fun for me. Let's get right to the video. Okay, so I drew out
the plan for the pantry with all the dimensions. You can see I'm going to do a two by four base
here so that'll be three and a half inches. The cabinets are 30 inches tall and then each of my
shelves are two and an eighth inch. All the spacing in between the shelves are 13 and a half inches.
We have eight foot ceilings and then you can see the space left here will be 26 inches. So we wanted
to make this bottom shelf a little bit deeper. This will be 15 inches and then all of these other
shelves will be 12 inches deep. So I got the measurement for the top of every shelf. Then I
marked out the measurements on my wall with blue tape so that I could visualize the spacing of my
shelves. I also taped out the cabinets on the ground just to see how much space they would take
up and then the corner here we can use for storing drinks or the recycling bin, whatever we decide.
So this wall is 56 inches and this wall is also 56 inches so I'm going to use the same exact plan
but I'll flip it around so the cabinet is on the left side there. So instead of trying to salvage
the trim, I'm going to take all the trim out so that I can put my base tight against the wall,
the back wall and the side wall and then once the cabinets are installed then I can go in
and replace the trim so everything is even and matches up. To remove the baseboard take a utility
knife and score a line in the caulk and then pry the trim away from your wall. I used a hammer but
a pry bar would work better. For my base I used treated two by fours and three and a half inch
construction screws. Once your base is constructed take a level to make sure that your base is level.
If it's not level use some shims to prop it up and make it level. Now I'm taking a stud finder
and marking out my studs so that I can screw the base right into studs in the wall so it's nice
and sturdy. I mentioned before that I got these basic upper kitchen cabinets from Home Depot.
They're 30 inches wide by 30 inches tall and 12 inches deep. I wanted my countertop to be 15 inches
deep though so I had to pull the cabinet away from the wall so there's a little gap in the back and
I just cut some extra blocking out of two by fours and then screwed my cabinet into the blocking
into a stud in the wall so that it was nice and secure. I could have made my own custom cabinet
so that I would utilize all the space but this just saved me money and time. I'm going to show
you how I plan to do the framing for the shelves so that'll go along the back wall. This one will go
along that back wall and then I've got this one
here and this one will go flush. This one
go here. So that's the plan for supporting the shelves. These back ones will go into
studs in the wall. Same thing with the side ones. We'll have another two by two here and then we'll
have some two by twos supporting the middle. For the center two by twos I'm going to drill some
pocket holes so I can drill the two by two into the other one. Same thing with these so I can
drill the two by two into the other two by two. I used two inch by two inch lumber for all of my
framing pieces. I laid everything out in the garage and then marked out where I wanted all
my pocket holes to be. Then I took my kreg jig and drilled all of my pocket holes. For all of
the frame pieces against the wall I made sure to use longer three and a half inch screws and
screwed them into studs in the wall. You want to make sure that these pieces are extra secure. For
my smaller frame pieces I used two and a half inch or two inch pocket hole screws. Especially for
this first shelf make sure it's nice and level because you're going to be taking your measurement
for all of your next shelves off of this one so make sure this is nice and level before you move
on to the next one. Now I wish I could have just constructed all the framing pieces in the garage
and then brought the whole frame inside and installed it but with how tight the space is
I wasn't able to do that so I just have to piece in all the frame pieces. Okay quick pantry update
I cut all of the top of my shelves. These are half inch plywood. They're not installed yet I just
wanted to dry fit all of them before I secured them. I did the top three shelves just in a
straight cut and then my bottom countertop I did a nicer 45 degree cut. It's not perfect but I can
just fill it in with some wood filler. The next step for me now is to place some eighth inch
hardboard so I'm going to use this hardboard underneath all of my shelves so you can't see
any of that ugly framing. After the hardboard then I can measure my trim to go over top of
all this wood so you won't be able to see any of that wood. It'll look like a nice chunky floating
shelf and I'm also going to use the hardboard for the ends of my cabinets. It's kind of hard to see
but since I pulled the cabinet away from the wall there's a little gap behind there but I'll put the
eighth inch hardboard on the side so that it'll look nice and seamless and you won't see any gaps.
To secure my eighth inch hardboard I'm using one inch brad nails and wood glue. Make sure to nail
in your hardboard where all of your two by two frame pieces are. I cut all of my hardboard pieces
down on my table saw. I bought one by three select pine board for my trim pieces and then just ripped
them down on my table saw to two and an eighth inch to fit the width of my shelves. I did a 45
degree miter cut on one end of each of my trim pieces so they fit together in a perfect 90 degree
angle. So I bought half inch sand plywood from Home Depot and it's spelled s-a-n-d-e. To get it nice and
smooth I started with 80 grit sandpaper and then did 120 grit and ended with a 220 grit sandpaper.
So I made sure to dry fit my plywood and my trim pieces first to make sure that everything fit
and then I took them out to my garage to sand down so that I didn't make a huge mess in my
pantry and kitchen. To install my plywood and trim pieces I used one and a half inch brad nails and
wood glue. Okay so all of the shelves are in. I installed the trim also. So all of the big stuff
is pretty much finished. I just have to do all the final touches which is still going to take me a
little bit of time. I'm going to fill all of the holes in the drywall. So I have this mesh tape
that I put over the holes and then I'll use this spackling. I also have this plastic wood
wood filler that I'm going to use to fill all the little nail holes and any cracks in the wood.
I'll also fill that seam with the wood filler and any other gaps in the trim and the shelf.
I'm also going to go in and fill all the little nail holes that I made with my brad nailer.
Everything that you see right here has been my progress within two days. So I'm going on day
three today. Hopefully I can get all the final details finished. After I fill all the holes I
can do the caulking and then I can paint. So the top three shelves are going to be painted white.
The cabinets are going to be painted white and then this bottom countertop will be stained a
darker color and I'm really excited to see how that turns out. After everything is painted I
can install the base trim and the cabinet hardware and that'll be it. After patching the holes in my
drywall I took a little black sander to knock down any high spots. Then I took this wall texture and
adjusted it to the medium spray and sprayed all the patches so that they have a nice texture to
match the rest of my walls. After the wood filler was dried I took my block sander again and sanded
down any high spots. First I wiped down the entire pantry to get rid of all the dust. Then I took some
blue painter's tape and taped all around my shelves and cabinets leaving an eighth inch gap
for caulking all of the seams. Now if you're going to use this hack for caulking your seams
make sure to rip the tape off as soon as you're done caulking before it dries or else you're
going to mess up your perfect seams. I made this mistake and waited for the caulk to dry
and then ripped off the tape and it messed everything up so I had to go back and redo it.
I bought three and a quarter inch base trim for my pantry and it wasn't quite tall enough
so I also had to install some shoe trim at the very bottom. After I installed the trim I made
sure to fill all the little nail holes and then sand that down once it dried and then I used some
caulk to fill all the seams to make everything look nice and seamless. Then I painted my trim
the same color as my cabinets. Last I finished off the countertop with three coats of polyurethane.
Be sure to look out for my next video where I'll be organizing the entire pantry and putting all
of our food back. Thank you so much for watching and please don't forget to subscribe!
