How to Finish Plywood Cabinets: Inside & Out | Sealing Plywood / Edge Banding / Painting Plywood

Make it in Style
41 followers
8 Video Views·Oct 22, 2022
In my last video I showed you how I built this drawer cabinet for my home office.
I'll be making a modular desk system where I'll build two of these base cabinets and add a solid
wood top to turn it into a desk. Now as you can see the cabinet is currently unfinished plywood
so today I'm going to walk you through my finishing process. Now sure painting furniture is
a pretty straightforward process so today I want to focus on two key things. Number one that's how
to prep your plywood edges to get a nice smooth silky finish when painting. And number two it's
to finish the inside of your drawers. Now the one thing I hate about homemade furniture is how rough
and unfinished that drawers look. You can see the exposed edges of the plywood and it's just rough
to the touch. So what I did for this cabinet is I actually pre-finished all the drawer parts before
assembly to make them look like solid lumber and nice and smooth to the touch to give them a really
professional look. So today I'm going to walk you through that process. Let's get to it. The truth
is that my cabinet has been sitting in my garage untouched for almost three weeks now waiting to be
finished. It's just been too cold to work in here and way too cold to apply finish. But I decided
enough is enough and headed over to Princess Otto to pick up a new space heater to help warm things
up. I cranked it up and could finally get back to work. Now usually you want to finish your cabinet
before assembly but I wanted to break down this project into two videos. First showing you how
the cabinet is built and then the finishing process which means I now have to take the cabinet apart.
Of course I don't need to completely take it apart. I'm just going to remove the drawers and then
remove the handles and attach the drawer fronts from the drawer boxes so I can paint them. By the
way it's a good idea to label your drawer boxes top middle bottom so you don't mix them up later
and the same goes for drawer fronts. I'm going to need to sand prep and paint and I don't want all
that getting into my drawer slides so here I'm adding some painter's tape to protect the front
edges. My first focus is to smooth out all the exposed plywood edges. If you just paint these as
is it'll look horrible so I'll start by sanding them just a little to smooth them out making sure
to break all the edges so they don't fray later on. To fill and smooth out the edge grain I'm going
to use DAP's premium wood filler which is great as a grain filler among other things. DAP has a
line of wood fillers to choose from for various applications and you can check those out using
the link down in the description below. Applying the filler was a little awkward for me at first.
You can tell I've never done drywall before but eventually I got the hang of it with a little
practice. My goal is to get a thin uniform layer to cover all the end grain. If you put on too
little the grain will show through but if you put on too much well you'll have a lot more sanding to
do later so the trick is trying to find the right balance. I paid extra attention to any voids in
the plies making sure to fill those and leave a little overfill. I covered all four edges of my
drawer fronts and the exposed edges of the cabinet too. Of course I tried to get it as perfect and
clean as possible but it's okay if it's not perfect on the first try as you can always come
back and hit it with a second coat. I decided to let my first coat dry for two hours and then use
some 180 grit paper to sand down the wood filler. I quickly realized that using my orbital sander on
the edges was much too aggressive even at the lowest speed setting so I switched to my micro
sanding block with 220 grit paper. I started by sanding all the edges using a really light touch
until the edges were smooth being careful not to remove all the filler. I could then flip over the
cabinet and go back to my orbital sander to sand down all of my plywood surfaces and eliminate any
fuzzies. There's no need to overdo it here just a few passes and stop when it's smooth to the touch.
I repeated the same for all the drawer fronts using the lowest speed setting for the faces
then switching to the sanding block for the edges and sanding lightly until it was nice and smooth.
When all the sanding was said and done I ended up with white powder everywhere which could be a real
nightmare when painting so to avoid ending up with grainy paint I used a damp cloth to wipe down all
the surfaces and remove the dust being careful not to overdo it and wipe away the wood filler
because warning it's water soluble. Okay so while I let that dry I can get set up to start painting
and I'll start with a coat of primer. This is the primer I've decided to use but whatever you choose
just make sure it's recommended for bare wood surfaces like this one. Here I'm using a foam
roller to apply a coat of primer to the drawer fronts and the edges. Now yes I do have a paint
sprayer but it's too cold outside and I don't like to spray indoors. It can be tempting to skip the
primer but it's an important step for two reasons. First it helps seal the wood so it won't show
through your paint and if you've ever patched a hole in the wall then painted it without using
primer you'll know exactly what I mean. And second the primer allows you to notice any defects in the
surfaces that you can fix before moving on. I let it dry for the recommended time and then inspected
the edges and wasn't surprised to find a few spots that needed to repair. I did a quick touch-up and
spot primed before moving on to the next step. Once dry you'll notice the primer is really rugged to
the touch and I know no one wants to hear it but sanding is really the key to a smooth paint job.
Again using the power sander on the edges will likely remove more paint than you want
so I stuck with hand sanding the edges. Just as before it's important to wipe off any powder
residue so it doesn't affect the smoothness of the next coat of paint. For the top coat I'm using
this cabinet paint. Now I'm no expert on paint but what I can tell you is that you don't want to use
latex paint for cabinets. It's just not durable enough. You want to look for alkyd paint which
will often say cabinet or enamel on the label. Initially I was going to use this paint but
another one caught my eye at the store, maybe because of the mention of premium on the label,
I don't know, but mainly because it's a cabinet paint that dries in two hours which makes it
easier to apply multiple coats in a single day. And by the way these are all water-based paints.
You'll actually see that I ran into some issues with this paint and I don't know if the paint
was the issue or not but just FYI my research also pointed to two other good cabinet paint
options which are Sherwin-Williams Pro Classic or Benjamin Moore Advance if you want to check
those out. I applied a coat of paint being careful not to press too hard so I didn't get
any roller lines and such and trying to get a really uniform coverage but I quickly realized
that I was getting a really bumpy finish which upon closer inspection appeared to be tiny bubbles
in the paint. I decided to let it dry hoping the paint would do its thing and even out as it dried
but I was horrified to see all the small craters and bubbles after it had dried. I figured okay
this is just the first coat let's just sand it out and the second coat will smooth everything out.
This time I moved up to 320 grit paper and lightly sanded all the surfaces again
and wiped away the dust then got to work on the second coat. Sadly after it had dried the result
was exactly the same. This sucks! All this prep work only to end up with such an ugly finish?
I don't think so. I could only assume that the foam roller was the issue. This paint is so thin
and fluid like water that the foam roller must be making it bubble up. After some research it
seemed that the best solution was to try a woven six millimeter nap roller rather than the foam
roller so after sanding it again and wiping it all down I applied a third coat using this new roller.
While we let that dry and hope for the best let's talk about finishing the inside of cabinet drawers.
Now here's a good example of what I don't want. Sure having exposed rough plywood is fine for
your shop drawers but I want the stuff inside my house to look a little more professional, you know?
The first step to finishing drawers, and this should all be done before you assemble them,
is to add edge banding to the top of the drawer parts. This was actually my first time using iron
on edge banding but it seems pretty straightforward. I cut a piece slightly longer than required and
set my iron to the hottest setting. It took me a few tries to get a feel for it but essentially you
want to move the iron slowly, keeping it flat, spending maybe 10 seconds per area until the glue
melts and it sticks on. Too long and you'll notice burn marks on your edge banding, too fast and it'll
tend to peel up. I used this edge band roller to ensure it had good contact all along the edges
and then set the piece aside to cool and let the glue dry. You may have noticed that if you don't
have a vise you can use a pair of parallel clamps to hold the piece in place while you work.
Once all the pieces had cooled I set the piece back in the clamps and used this edge band trimmer
to cut off the excess and then clipped the ends with some scissors. I'll leave a link to this tool
down below if you want to check it out. Now I've heard some people say they prefer to use another
method because the tool can cause some tearing. My first few were perfect and then I did experience
some tearing on a few but ultimately I was able to sand it out so it wasn't noticeable.
It also helps to use a file to flush up the extremities. I sanded the edges using 220 grit
making sure to remove any visible adhesive or any excess edge banding until everything was
flush and smooth. Ultimately when you're done your plywood should look almost like a solid piece of
wood. Now apparently you can buy pre-finished plywood that's finished on one side but I've
never come across it where I live so I'm going to pre-finish it myself. For this I'll be using
two products shellac and water-based polyurethane. I'll leave links down below. The first step is to
seal the plywood using one coat of shellac, ideally using a natural bristle paintbrush.
Shellac dries really fast so you can flip it over and do the other side quickly without forgetting
to coat the finished edge too. After about an hour or two shellac can already be sanded using 320
grit paper. I'm just hitting it lightly to knock out any imperfections and make it smooth to the
touch. Typically once the sheen is gone it pretty much means it's done. I wipe down all the pieces
with a slightly damp cloth to remove any dust left behind by the sanding and then applied a
single coat of water-based poly to all the drawer sides and the bottoms too. I personally like using
a foam brush for this to apply an even thin coat. And that's it! Once dry you'll have silky smooth
drawer parts that are ready for assembly. The plywood is soft to the touch and looks like solid
wood. If you want to see how I made the drawers and install them in the cabinet just click the
link in the top right corner to check out that video. And now's the moment of truth. Back to the
cabinet paint to see what kind of finish we have. Well the six millimeter nap roller was definitely
an improvement over the foam roller but it still has a few bubbles and an orange peel texture.
I definitely do not recommend this paint. On the other hand what I do highly recommend is DAPS
Premium Wood Filler. It really made the plywood edges disappear and was so easy to work with.
This is the back of the cabinet where I didn't use the wood filler just for reference.
Hey I hope you enjoyed this video and don't forget to check out my previous video where
I built this drawer cabinet. And stay tuned for my upcoming video where I'll be turning
this cabinet into a modular desk. So be sure to subscribe if you want to follow along.
Until next time, thanks for watching. See you soon!
