Balancing The Rotating Assembly - New Pistons & Reman Rods - '68 Firebird 350 Engine Rebuild - p8

Auto Pack
29 followers
6 Video Views·Oct 20, 2022
Hey everybody, welcome back. Today we're going to be going through the process of balancing the
rotating assembly on the 350 Pontiac engine. In the interest of full disclosure, I want to point
out that balancing is a newer process in our machine shop, so I'm open to suggestions and
advice on how to lean out and improve this process for the future. To start with, we want to weight
match all of our pistons and piston pins, so I started by checking and recording the weight of
each pin, followed by doing the same thing on the pistons. The pistons we're using are a stock
replacement aftermarket cast piston, and as such the castings can be a bit further off from the
factory when compared with a set of forged or billet pistons like you might see in a high
performance high dollar application. With each of the pistons having been weighed individually,
it looked like we were coming in at maybe around two grams difference across all eight of the
pistons. The piston pins were also a little bit different from each other, so I went ahead and
took the heaviest pin with the lightest piston, you know, the second lightest with the second
heaviest, and so on, just to get us a better starting point before we start actually doing any
modification or material removal on the pistons. In an ideal world, you want to be removing as
little material from the piston as possible, because more material to remove means that the
job is going to take a larger amount of time, and if you need to remove excess material, you may run
risk of weakening the structure of the piston. With the pistons and pins paired, we're going to
go through again and record the weight of each assembly. Once we know the lightest piston and
pin assembly, we're going to remove material from the other pistons to make them weight-matched
within a reasonable tolerance. How you decide your tolerance really depends on what you're trying to
achieve with the engine and what the application is, and in the case of this stock 350 Pontiac,
it's hard to say whether or not a couple of grams difference in the pistons would really have a
effect, but it doesn't really take that much time to get them closer. With around a gram and a half
difference, it won't be too difficult to get these within well less than half a gram, and if not
closer to within a tenth of a gram, and this is kind of where I need some advice from people on
what tools really help make this go fast. I know some people put the pistons in a mill. Here I'm
just using a little burr for aluminum, but it's kind of coarse and doesn't leave a great finish,
so I came back with one of our Dremel tools with a little sanding disc on it to kind of clean that
up a little bit, and again, where we're removing material here is somewhere where it's not going
to have any structural effect on the piston. Obviously, we're not going to be out grinding
on the skirt or, you know, taking a ton of material out of the boss around where the piston pin,
you know, is supported. I also did my best to grind evenly from both sides of the piston,
which again, you know, without having any hard data to test, I don't know how much of an effect
that really has when we're talking about, you know, less than a gram and a half, if not,
you know, less than a tenth of a gram, so let me know what you guys' opinions are on this,
because like I said, I'm new to the balancing process and I'm learning, but I'm just trying
to do the best that I can without wasting time doing obviously way more than what's really
necessary, especially in an application like this. There you saw across all eight pistons
were within about a tenth of a gram, so now we're going to move on to balancing the connecting rods.
This does get slightly more complicated than balancing the pistons because not only do we
have to weight match the entire weight of the connecting rod, we need to weight match both
the big end of the connecting rod and the small end, so the fixture you see there allows us to
weigh just the big end of the connecting rod when it's set up the way that it is right now,
so I went through and recorded all of the weights of the big ends of the connecting rod so that we
can start there and go ahead and do some grinding on the balance pad there that you see since these
are stock connecting rods. Again, they have a lot of room there to make adjustments on the balancing
and obviously this fixture has to be set up pretty well, and I know it looks kind of janky there with
the blue tape holding everything down, but that's just because I haven't gotten, you know, a dedicated
space set up in the shop yet because we're kind of doing some rearranging to get everything set
up, so eventually I'd like to have something more secure looking than this, but this worked very
well in the meantime. And here again, obviously we cannot add weight to the lighter rods, so we're
grinding material off of the balance pad of the heaviest rods until they match the weight of the
lightest, and this is another thing where our belt sander that we have is not really optimally set up
for this, especially on these rods here that it was kind of difficult to get at the balance pad
without grinding on the rod bolts and the nuts. Obviously I was able to get it done, it just
required a little bit more work and, you know, a little bit more care taken to make sure that I
wasn't grinding on the rod bolts or the rod nuts. As you can see, I'm also flipping the connecting
rod every so often so that I can make an attempt to grind pretty evenly on both sides again,
but if anyone has advice on what type of sander they use when balancing connecting rods,
let me know that in the in the comments as well. For a good little bit of grinding on the big end
of each of the connecting rods, we were able to get them within about two-tenths of a gram there,
which I think was perfectly acceptable as a starting point, so now we're moving on to weighing
the small end of the connecting rod. So you can see I did a little bit of changing there on the
fixture so that we can weigh the small end and get an idea of how much we need to grind off of
each of the balance pads on the small ends of the connecting rods, and this is a lot easier to grind
the small end of the connecting rods because I'm not worried about hitting the rod bolts or the
rod nuts there, and I can kind of just rock it back and forth there and get a nice even grind
across that entire balance pad. Again, obviously this is kind of the most labor-intensive part of
the balancing process, at least in my book, and as I'm going through, I'm checking the weight,
coming back, grinding a little bit more, checking the weight, kind of letting everything cool because
you don't want everything to get super hot. It is really just a bit of a process that there's not
really a lot of science to it, it's just, you know, doing some grinding, going back, checking your
weight, and just getting a feel for, you know, how much grinding equates to how many grams. So
once I had the small ends of the connecting rods weight matched within our tolerance,
I went ahead and double-checked the big end of the connecting rod, as well as the overall weight,
and I just had a couple there that I wanted to do a little bit of fine-tuning on,
so I went ahead and, you know, did a just a tiny bit more grinding to get them really close.
They came out really well, so now we're going to go ahead and weigh one of our
rod bearing shells, as well as our
