I Deleted The AFM And VVT From My 5.3L LS V8! - First Startup - 5.3L LC9 Gen IV LS V8 Build Part 4

Auto Pack
29 followers
6 Video Views·Oct 20, 2022
Welcome back to the Jamzy Online YouTube channel. We're jumping right into the video here with
polishing the crankshaft out of my personal 5.3L LC9 engine, which experienced the common
failure of an AFM lifter. Luck was on my side, however, as the crankshaft had virtually no wear,
and in fact the main bearings and rod bearings looked nearly perfect upon teardown,
meaning a quick polish after the balancing was all the crankshaft needed to be ready to run.
With everything clean and ready for assembly, it was time to verify that our main bearing
oil clearances were acceptable for this application, so we miked all of the main
journals of the crankshaft and transferred the measurement to a bore gauge in order to
measure the clearances, which came out around just over 2 thousandths on all journals.
Satisfied with the main bearing clearances, I went forward to double check the rod bearing
clearances in a similar manner. Running a set of 1 thousandths undersized rod bearings put me
between 1.7 and 2.1 thousandths clearance on all 8 rods, which is on the border of the tight side
of where I wanted to be, but standard bearings opened it up farther than I wanted to see.
Knowing that all of our crankshaft bearing clearances were within our determined tolerance
for this application, it was time to move forward with getting the crankshaft installed in the block.
As you can see, we're running a set of ARP main studs and giving the bearings a quick
coat of clevite bearing guard before setting the crankshaft in place, and also giving the
lower bearings in the caps a quick coat before setting them in place and tapping them gently
until they have seated in the block. It's recommended to use a small dab of silicone
sealer under the head of the side main bolts to avoid future oil leaks, and after lightly
snugging down all of the fasteners, we bump the crankshaft back and forth a few times,
ending with bumping the crankshaft forward in order to align the thrust bearing.
At this point, we're free to go ahead and tighten down all of the main caps,
being sure to follow the recommended torque procedure from ARP bolts.
With all of the main caps seated and torqued, it's always satisfying to give the crankshaft
that first spin by hand and make sure everything is feeling okay. Finally, we'll go ahead and
double check the crankshaft end plate, which came in just over 3 thousandths, which I'm satisfied with.
I want to take a quick break to give you guys a little bit of an update. This is the new shop
that we're working on. We just pretty much have to finish the interior and some of the electrical.
I also have my pickup here, and the engine is almost installed. I'm almost ready to do the
first fire, so that's what you guys can stay tuned for. I also want to take a minute to talk about
our sponsor for this video, Skullbliss. Skullbliss offers ethically sourced animal skulls in a
decorative fashion. Their process takes authentic skulls, which are a byproduct of local Balinese
agricultural industries, and transforms them into detailed works of art that offer an impressive
touch to any home or office. Their unique process and attention to detail yields a work of art that
someone like myself can truly appreciate, knowing that in a way it's similar to the attention to
detail required in the work I do here in the shop day in and day out. And while this longhorn skull
looks absolutely amazing mounted to the front of my dad's little Ford Courier, I think it's going
make a great housewarming gift for my father-in-law who recently moved to Texas. We want to say a huge
thank you to Skullbliss for recognizing the hard work we do here in the shop and reaching out to
share their work with us and our audience. If you or someone you know has been looking for the perfect
finishing touch to their home or office, be sure to check out the links in the description and let
them know that we really appreciate their support of our channel. Thank you for staying patient for
the quick sponsor break, but jumping back into it here we're installing the new camshaft that I chose
for this build. Being a daily driver, I didn't want to sacrifice too much drivability so I decided
to go with the Elgin 1838P, otherwise known as the sloppy stage one cam. This cam does away with not
only the AFM system but the VVT system as well. With the cam thrust plate installed, I installed
the crankshaft sprocket and I opted to go with Kloy's three-way adjustable timing set, allowing
me some adjustability to advance or retard the cam if needed. To start with, I'm installing it straight
up or dot to dot in order to degree the camshaft. For a quick rundown on degreeing the cam, first
step is to get the degree wheel installed at true top dead center. Using a positive stop on the
piston, we rotate the crank until the piston hits the stop, noting the degree of the wheel before
rotating the opposite direction until the piston stops again, and adjusting our pointer to make the
two numbers match, which gives us an accurate top dead center. It might take a try or two if you're
dumb like me and move the pointer the wrong way the first time. At this point we'll have a lifter
and an indicator installed on the intake lobe of the cam. Right there, we're 50 thousandths intake
open to after top dead center, and the spec on the cam is 50 thousandths timing intake opening at
minus two before top dead center. So we're on the money there. So there's 50 thousandths on the way
closed. Should be 39 after bottom. Pretty, pretty close. While we had a piston installed for checking,
I decided to go ahead and double check our piston and valve clearance, even though I have a pretty
mild cam, but it's better to check than wish you had. If you follow our short form content on shorts,
reels, or tiktok, you probably already saw this video in depth. Long story short, we had plenty
of clearance. Moving forward with getting the rest of the rotating assembly installed, we went ahead
and checked our ring end gap. Out of the box, the Hastings rings I'm using had 20 thousandths end gap
on the top ring and 19 thousandths end gap on the second ring, which is acceptable based on the
recommendations from the piston manufacturer for our desired application of this engine.
Knowing that our rings were ready to go, it was time to go ahead and get the pistons mounted to
the connecting rods. The forged icon pistons that I'm using in this build are a full floating design
and as such use circlips to retain the wrist pin and keep the assembly together. We start by working
one of the clips into place following the recommended orientation from the manufacturer.
It's always necessary to lubricate the moving components like this, so as we're building the
assembly I like to use a bit of assembly lubricant in the bores of the piston as well as on the rod.
Once the wrist pin is in place, it's as simple as installing the circlip on the opposite side
of the pin and double checking that they're both fully seated, ending with a bit of oil
worked into the moving parts. Installing the rings is a pretty simple process when you get
the hang of it, starting with the lower oil control ring and then installing the second
and first compression rings, being sure not to spiral on the compression rings and risk damage.
The orientation of the ring end gaps seems to be a controversial topic among the industry,
but I simply follow the recommendation of the orientation from Hastings,
as my rule of thumb is to trust the people who engineered the parts that I'm using.
When you have a ring compressor that works well and the top of the cylinders has been properly
chamfered, installing the pistons is really a breeze. Generally we run a thick bead of
assembly lubricant around the cylinder wall before installing the piston,
and then tap the piston into place carefully to avoid breaking any rings.
I typically install both piston assemblies for one rod journal of the crankshaft before rolling
the engine over on the stand and pushing the pistons down the cylinder until the connecting
rod seats against the crankshaft. I should also note that the rod bearing has been lubricated
with assembly lube prior to the installation as well. As always, a note on that not-so-common
common sense is to keep an eye on everything and avoid dinging the crankshaft or damaging
the bearing as you're pushing it into place. These are the stock Gen 4 cracked cap connecting
rods original to this engine, but as you may remember, we did go with a set of ARP rod bolts.
After lubing the crankshaft, the caps are installed, being sure to correctly align them
and seat them before tightening them down completely. Previously we've determined a
torque spec that gives us the 5.5 thousandths to 6 thousandths bolt stretch recommended by ARP,
and at this point we'll go through and double check that all of the bolts are torqued to that
spec and our rotating assembly is fully installed. Everything seems to be rotating nicely and we do
have connecting rod side play so we're good to move forward. At this point, we're installing
the oil pump. Since I've done away with the AFM and VVT systems, I simply went with a Melling
standard volume, standard pressure oil pump. Following Melling's recommendation to align the
pump, we bring the mounting bolts up just snug and rotate the crankshaft at least one full revolution
before torquing down the bolts. With the ARP main studs, I did have to grind a couple of larger holes
in the windage tray before installation, but it was only a minor modification and a quick and easy
install, saying goodbye to our view of the crankshaft once and for all. At this point, we headed back to
the top side of the engine to get some of our valve train installed, starting with lubricating
the lifter guide trays and installing our new LS7 valve lifters on all eight cylinders, doing away
with those pesky AFM lifters that caused us failure in the first place. Before installing the heads,
it's important to remember to tighten up the bolts on those guide trays. For our head gaskets, we're
using the OEM style multi-layer steel head gaskets, paying attention to install them in the correct
orientation with the front label towards the front of the engine. We'll set our freshly built heads
in place on top of the engine and install the ARP head bolts that we ordered, being sure to follow
the recommended torque procedure and pattern from ARP, as well as using the provided ultra-torque
fastener lubricant. As a quick reminder, you can find thousands of parts like the ones in this video
for sale on our website, www.jamzeeonline.com. With the heads bolted on, the engine is really
starting to look closer to being ready to go back in my pickup, but first we need to finish up
installing the valve train. To test out one of the products we sell on our website, I decided to go
with the Yella Terra ultralight rocker system, which are an aluminum body, roller tip, shaft,
and pedestal rocker arm setup. With cylinder one on the base circle of the camshaft for both intake
and exhaust, we install our push rods and slowly tighten the intake and exhaust rocker arms down
evenly until we achieve what is effectively zero lash. At this point, we tighten down the rocker
arm bolts evenly in quarter turn increments, taking note of the number of turns required until
the bolt is completely tight against the pedestal. As per the instructions, each quarter turn of the
bolt seems to equate to roughly 10-12 thousandths lift or preload. In addition, the instructions
indicate you may need to use a shim under each pedestal, as I am here. With the number of quarter
turns counted, our intake side will have around 25-30 thousandths preload, which may be a tad
light, but the exhaust is right where I want it at around 35 thousandths to 40 thousandths preload.
Knowing that we're happy with our preload and our geometry looks good, it's time to go through and
do the final assembly of the valve train. Each end of the push rod gets a dab of assembly lubricant,
as well as the tip of the valve stem, and in addition, the roller components of the rocker
arm receive a bit of oil to ensure they have lubrication upon initial startup. Again, given
that the intake and exhaust rocker arms are mounted to the same shaft, it's important to tighten their
bolts down evenly before the final torque. While the instructions say you only need to check the
preload on one cylinder, it's a habit to roll through the firing order and check each setup
with the lifters on the base circle of the cam for that cylinder, just for peace of mind. Finally,
we're ready to cover some of this stuff up, but these rocker arms do require a bit more space,
so we have an extra thick valve cover gasket and nuts on the valve cover bolts, which act as a
spacer to keep the valve cover from interfering with any of the rocker arms throughout their
travel. Now we're going to give the valve train hopefully one last look for a long, long time,
and get it covered up so that we can move on to wrapping up the final touches of the engine.
The rear cover is reused, but a new rear crank seal will be installed, which is done by simply
pressing the seal carefully into the cover, using a bit of lacquer thinner as a lubricant to make it
go smoothly. The rear cover is carefully installed to avoid damaging the seal, and the bolts are
brought up just snug. Similarly, the new timing cover, which replaces my VVT timing cover, is
installed and again brought up snug, not tight yet. Using a harmonic damper install tool, the
damper is carefully installed onto the snout of the crankshaft. Using the old crankshaft bolt,
which I should note is torqued to yield and should not be reused, we torque the bolt to ensure that
the damper is fully seated. At that point, we remove the bolt and install a new ARP crankshaft
bolt and torque it to the proper specification. The damper being installed helps align the timing
cover, at which point you can final torque the bolts as long as you're sure to keep the bottom
face aligned with the pan reels of the block, as goes for the rear cover as well. All four corners
where the block meets the cover should get a light bead of silicone sealer to prevent any leaks before
our oil pan gasket is installed. By the way, I also installed the oil pickup tube somewhere along the
way with a proper new o-ring, and I also replaced the oil relief valve in the pan with a plug since
I have eliminated the VVT and AFM. With the pan in place, the bolts can be evenly snugged up,
and this engine build is nearing completion.
