Will It Run After 20 Years- - RARE 1959 Willys CJ3B -High Hood- Jeep - RESTORED

Automotive Turbo
30 followers
15 Video Views·Oct 20, 2022
So guys on this episode we're headed to a buddy's house to pick up a 1959
willys cj3b jeep. Now we bought this jeep completely
sight unseen other than just a few pictures that he
sent to us over facebook messenger. Now the story that we got behind it is
that this thing's been setting up for quite some time now. He's really unsure
why it was parked or even if it was running when they parked
it. So we're hoping we can get it back to the shop
dig into it a little deeper and find out that this girl still has some life left
Well kind of nice not having to dig out 30 pounds of rat's nest right off the
bat. See what you got to work with right as soon as you open the hood.
A little old four cylinder. I think it's what they call a little hurricane.
A little 134 similar that's in that little willys
male jeep we've got. I don't know plugs don't look
too old on this side so that's a good sign.
Everything look to be there. Plug wires are fine. I mean as far as I can tell
they're not all chewed up or anything. Everything's here. I don't know if we got
check the oil in it. That's got antifreeze in it. Oh wow.
I was not expecting that one bit. Kind of thin ain't it? Yeah kind of thin.
What's it smell like? Gas. Really? Doesn't have any taste.
I wonder if it'll. Of course. It's just slipping there. Water
pump's not stuck though. I guess let's pull these plugs out and
try to get on that crank and see if it'll turn over.
Okay. I mean as we know our luck here lately everything's been stuck so
I'd rather know that that was something we can mark off.
You got a 5H or a 1316?
Fingers. Took them out by hand. It's gonna be the big 1316s.
And they're all just finger loose.
Why is that? Now one I'm gonna have to take out.
I'm just gonna spray a little PB Blaster down in there to start off with just to
give it a little or some oil to squirt down in there
whichever one. Just to give it a little slippage.
I'm assuming we're not in gear right? I don't want to go
in gear nothing. It's got it right there. So it won't go in gear or anything. It's
kind of like it's just stuck in neutral.
So we'll have to address that. Right. Surely it's...
The clutch does go down.
And now we're lifting the whole motor. I think it's the other direction.
I hate that. It's like it's just, they've just been following us here lately.
You can drive that. We're gonna have to let it set.
Well I guess we'll get some vinegar or diesel or something down in
them cylinders and let it set a day or so.
Yeah. We can go ahead and pull this valve cover off too just to see what it looks
like on the top end. Might not hurt to drain that oil as well
and make sure there ain't no water or anything in it.
Kind of crazy I noticed this thing has power steering on it.
Oh yeah. Sure enough. Now that wouldn't have been factory. No it doesn't look like a
factory bracket anyway. I wonder with the plugs being
finger loose or finger tight if someone hadn't already tried to
put something down in there. Right. Yep. Flat blade. I bet I might pull this
linkage off here. One good thing about it it's got nice
little work tables here don't we? Yeah.
Yep. Let's see what we got. Don't look bad does it?
No. No. Don't look terrible. The only rust I see is where it's on these outer
bolts we're coming through. Yeah. I mean there's even oil right
still up in on top of the head. Crazy. Where's the other valves?
I don't know unless these has the intake valves in the head and
the exhaust valves down in the block like a flathead would be.
That almost has to be. That's the only thing I can figure.
It ain't gonna run off just four valves. Got to have something let fuel and air
and let all that combustion out. Right. Weird. So now that we've dug into
this thing a little deeper we found out that it is indeed locked up just like
the last feels like 20 we've worked on here. So
the spark plugs were only put in there finger tight so
that's a little scary. Maybe someone knew this was locked up. They've already
messed with putting stuff down into the cylinders
and didn't come to any kind of headway on it. So
we're going to just try to put some vinegar or some diesel some marvel
mystery oil. We've tried just about every kind of
solution there is and none of them have worked great for us. So we're going to
get something down in there. Hopefully that allows it to break
loose so we don't have to pull the engine out to tear into it further.
Up underneath the valve cover it really doesn't look that bad up underneath
there so that's a good sign. If we can get this to turn over we can
just move on to the next problem from there.
Yeah that is super thin. I thought it was thin water.
Yeah a little bit. They should have separated if there was a lot you know.
Actually not as bad as I figured it might be though.
I think we probably just go ahead and put some diesel in that block.
Let it set because if that vinegar breaks through that cylinder is going to
mix with good oil anyway so that crank wouldn't hurt to
soak in something that'll clean it a little bit more.
But hopefully it's just stuck in the pistons. Just a waiting game at this
point. Right. So it's been about a week now we've
let this thing just sit. We've even rigged up basically our bar
that we've got down on the crankshaft here.
We've got it strapped down to the wheel hub there with just a little bit of
pressure. Hoping that over time just that vinegar
setting in there will help it to break free. So
we're about to dig back into it and hopefully find out that we have made
some progress. Just to kind of give you a little run
around on this Jeep up close here before we dig in too far.
We did find out that it does have a power steering setup
which is pretty cool but being a Jeep this small it probably wouldn't needed a
whole lot of help. But you can see where they had to cut this
grille here for the power steering lines to come down through
into that steering box right there. Now if you notice this
this Jeep has kind of a taller grille here and also
what they call a tall hood. So this is a CJ3B.
The B meaning that it had a taller hood on this model right here. So
pretty cool you don't see a whole lot of this style of Jeep running around.
At least I haven't come into them a whole lot. On the sheet metal here
it's in really good shape for how Jeeps are normally around our area.
Now I've had a bunch of CJ5s and normally they're rusted plumbing too
right here. I guess it's just a weak point on the design.
This one here is in pretty good shape. Did have a brand new gas tank up in here
so that's a good sign. You can tell this steering column it's
not an original. It's been switched out with the newer model
Jeep here. Kind of got a busted up windshield there.
No seat here. A terrible passenger seat over there.
Once again the sheet metal inside here we've got a spare tire.
But up underneath here well we do have a little bit of rust right there but
that's definitely very easily to be repaired.
Do have our tailgate. Lights back here. This side's basically the same. Pretty
good shape. All the tires are holding air and most
importantly all the wheels are rolling so none of the brakes are locked up. So
if we can't get this motor to turn over by the crank there
we'll try to get this shifter which is stuck right now. It's stuck in neutral so
we may have to work on it to try to get it to go in gear.
But if we can get that to go in gear then we can just rock the Jeep back and
forth in gear and hopefully the engine will break
loose after that. Still nothing that way. Let me try this
other. See this vinegar at the tops of the
cylinders there looks rustier.
Let's try back the other way just for the fun of it.
I'm loosening the nut. Well that's not good. No. As tight as that
thing's stuck I don't know that even getting it in gear would be
and rocking it would do any good. But it would be more sudden where that's more
just a little slow pressure getting it in gear and rocking it back
and forth both ways. Well I kind of messed with it the other
day and it's it's stiff but it will go in I guess
first and reverse. Oh yeah.
Won't go in third. Oops. Hey but I think it's is it for sure
going in. Yeah it seems like it down there. Yeah.
Huh yeah let's try that I guess.
Pull this off just so it doesn't fall and make a bunch of noise.
They were just sliding across the concrete. Right yeah I thought the back
tires were sliding. It ain't even trying up here.
I mean it ain't even trying. It's not enough weight back there. I know.
It's sliding across the floor. One of the things that's our advantage is it's
light that we can do that but disadvantage because it's too light.
Man I never thought that it would have been that stuck.
You know I don't know all these spark plugs
have rust where it's cupped there and I always wonder if they didn't
from them being not in there tight and if the hood was left open
if it rained it probably filled those things up.
And then with it having the valves down there too
all those could be rusted as well. True yeah.
Because that water would have got down on that.
I hope not. I mean the only way you'd really know on that is pull that head
off which I really don't want to do but
try it one more time. I don't know out of the two gears we got
which would be better. This one. The one that works I guess.
I'm ready when you are. Oh man. Not that one.
It ain't trying. Try the other way. I guess.
Did enough to make me dizzy. Well I don't know that waiting I mean
unless we wait a long several months. Right.
I don't think it's going to do us much good. We don't really have several months
to wait. I'm gonna pull that head off if we can
find a head gasket. I don't really want a chance going back
with an old head gasket after the last one. Let me see if I can
find a head gasket. It doesn't look like that one will be
too hard to pull off. The manifold on the exhaust is actually
just mounted to the block there. So I think mainly just pulling loose some
hoses. You know we'll have to catch that
coolant and stuff but it's just scary. We've got decent looking
coolant, decent looking spark plugs, a new gas
tank. It's like someone had plans to use this.
Yeah. But why is it locked up so solid? You know
did it get, were they you know driving in it overheated and seized up or
did they just have to walk away from it and that's an issue.
Yeah it's not just a hunging hung. No it's locked. It's stuck pretty
good. Let me see what I can find on that head gasket. Okay.
It's crazy how good it looks up here on this top end though.
I know it's, I don't know if it's crazy or scary.
All them things are long. They don't look bent.
They do look a little rusty. Yeah there's something on that one for
sure. It's just rust on the outside. I thought it
was rusted through. Some of those are tight.
Yeah I don't think there's been one that we've messed with lately that's been
stuck we haven't had to take the head off on. Yeah. Like every
one of them. Look at that gasket there. Whoa.
Yeah that don't look right does it. Looks like it's shrunk in and
huh that's weird. Yep bet she comes off now.
Might just leave it down in there come out all the way.
Wish I can get it somewhere. Got it. Pretty rough looking. Yeah them
valves look bad too. What does the bottom of the head look
like. That one right there. Right there I don't know. Pretty rough ain't it.
Stuck open. Oh that's gonna be our main problem I bet you. Maybe the third one
this one here. Yeah. Yeah that looks pretty nasty. It is nasty.
I don't know what that like you say it's kind of oily.
Yeah there's no telling because that one's
that one's wide open. Yeah it could be just the way the
the cam is on those though but I don't know.
I don't know do we want to just grab the shop vac and clean that out of there to
see what we're working with other than swamp water. Swamp water yeah that's
gonna be the easiest thing to. Oh wee wee wee you feel that. That is
bad. Very bad. Yep I don't know that's salvageable.
Let's grab that vacuum cleaner and see how it cleans up.
It's only the top the cylinders go way down in there it's a top inch and a half
it's still really rusted there but down below that it's not that bad.
Right. You'd have thought the piston would have been up to that point right
there but I don't know if that'll clean off or
not but like I said at least down in there and the rest of them
I think that's going to be our main problem. I think so.
Rest of them ain't that bad and that's the one that the intake valve is
stuck open on. Right. So I bet you hood was open some water come through
the carburetor area maybe through that gasket area or something
and filled that cylinder full of water there.
So we'll just have to start cleaning it up a little bit more might have to hone
that just a little bit but I think we're only going to be fighting
one piston though rather than several. I think so.
Hopefully but then again I never thought we were going to have to
I didn't think this would be stuck more more or less have to pull it apart.
So now that we've got this head pulled off the block it looks like we're
probably only going to be fighting one cylinder the third cylinder back here.
As you guys can tell here it is just extremely rusty the top inch and a half
two inches on here so I mean you can just feel the grime and rust on that.
These other cylinders really aren't so bad so hopefully it's just going to be
this one we're going to have to fight. Now once we pulled that head off we
noticed that the intake valve was open on that cylinder as well.
So more than likely the hood was left open it got rained on it poured down
the carburetor maybe it was that intake gasket between the carburetor and
the intake that allowed some moisture to come in but somehow a lot of water
got into that cylinder. So now we're just going to have to wait it out
clean it up a little bit more hopefully start working it back and forth.
Now if we can get it to work loose we'll put everything back together
and basically start off where we started to begin with in the first place.
I think these ones will be going up but I'll give them a little
movement in that one. Is it moving? Yeah. Spray it a little bit more with some PB Blaster.
It's probably just going to be slow. I'm almost positive I'm feeling
some movement there.
Something's turning. Not there. Nothing there but on that one it's
trying to see if I can keep an eye on the pulley. Think so? It's going somewhere.
Let me grab this light and check it out see if I can see if it's moved in the cylinder.
Yeah I think so look back in there see what you think.
Yeah it's moved about a quarter of an inch. Yeah a little more yep.
Let me try to clean that it's kind of nasty looking.
Yeah that's moved. These ones be coming up and those ones are going down.
Ready? Yep. I can watch you move out of the corner of my eye there.
That's good he's gone. I almost made it to the top. It does look rough in there though.
I think once we get this all the way down we need to clean it again. Yeah because it's
going to hit that going back up. Yeah I don't want it to break one of those rings.
Now I think so. Yep. Cool. Yeah let's clean out that cylinder really good
and then try to work it back down. Now that we've got this thing slowly turning over by hand we're
just going to go ahead and pull the starter off as well. Be sure that it's cleaned up nicely and
everything's working on it. That way hopefully we can pop it back on there be able to turn it over
with the starter. It'll turn over a lot faster and hopefully allow this thing to turn over a lot
easier. It's speeding up a little bit. Yeah I should say it's not completely got all on this
piston here. I'm trying to get some of the dry spots there. I'm hoping that transmission fluid
will help clean up those rings a little bit. Looks like all the
all the valves are opening and closing like they should on this part so that's good.
I think it'll turn over a lot better too once we get that diesel out of the block.
Get some oil down in there. Something that's made to move. Slick it. I think we can just kind of
keep working it a little bit and then I guess the next thing is we need to go ahead and make sure
get our valves working on the head there because I know we got at least that one that's stuck.
Get those valves working and then putting it back together I guess.
See what it does.
Turned over good now. Did you did you see how that back that fluid's coming up and it's kind of
and dropping back down in there? Uh-uh. Kind of watch it there.
Kind of making a wall. Yep.
I want to try to get that head I mean get those valves working on that head that way we can put
it back together. So on the head of this engine as I stated before it only has the intake valve so
the exhaust valves are actually in the block. We found out all of them are opening and closing the
way they need to be. Now if you see right here on this very rusted top of the part of the head
right there that valve is stuck open so a lot of water come down through the carburetor and just
cause this valve to stick open there. So what we're going to have to do is just try to take
some air clean that up the best we can and then just take a small hammer and try to work it back
and forth with a little PB blaster and stuff like that. Now you got to be very careful that you
don't bend there or break this valve because if you do that your engine's never going to run right.
So we're just going to try to take it easy clean it up just a little bit work it back and forth.
Hopefully none of these other valves are sticking but we'll go ahead and check them
while we're at it as well. So I believe we've got most of these intake valves where they're not
sticking any longer in the head. We're just going to try to keep cleaning up on it as best we can.
Also clean up the top of this block around the exhaust valves on it. Now we'll go back with a
new head gasket basically put this head back on the engine torque all the head bolts back to spec
throw that rocker arm on there and hopefully find out that all of our intake valves are opening and
closing nothing sticking and then we'll be able to move on to the next step from there.
Pumping up oil too so that's good. Everything looks to be moving pretty good.
I think we're back to where we can start putting it back together. Yep. So now that we've got the
top end put back together on this engine it appears to be turning over and sounding the
way it needs to be. We put new oil in here new oil filter as well. We see that our oil pump is
pumping it up here to the rocker arm so that's good and all of our intake valves seem to be
opening and closing the way they need to be. We still got to throw the carburetor back on there
but since we have it off we're just going to go ahead and have dad clean it up while it's there
and replace that carburetor gasket. Now I'm going to go ahead and tackle on the ignition system here
and what this jeep has up underneath this distributor cap is actually going to be what
they call a points and condenser system. So this is your condenser and this is your little points
right here. As you can tell they are extremely corroded up right there on the tip which is very
common for something that's been sitting a while. So we'll go ahead and replace these points and the
condenser. It's just too easy not to. Put a new rotor button on there and then hopefully we'll
be able to turn this over. It'll be getting a little fuel getting a little spark and hopefully
getting a little power. Oh it's coming out the bottom of the carburetor there though. Well it's
probably that that uh pump down there that it was it was nasty down in there. It's leaking out
about as much fast as I can put it in there. We'll just see what it does. Ready? Yeah.
Uh-oh our wire come off. I've seen something move and I didn't realize. I've never seen one
crank up that quick. Nope. I was not expecting that at all. I think you could have kept it
running. Probably so. But our cool wire jumped off there. Let's try it one more time. Not really even smoking
that much. No that's what I thought. I thought the thing ought to. It may pop off again. Let's
see if I can get it a different way here. Well that's good. Here we go. Hard to idle it with that.
Yep. And fortunately I think that carburetor may have to be taken back off and rebuilt if that's
leaking that bad. It's something in there. Seal of some sort is
dry rotted away or something. Everything that was in there was bad shape. Yes. I think we can pick
up a rebuild kit. Probably ain't 20-30 bucks. Get some fuel. Get us a fuel tank ran to it somehow.
Rather if we gravity it to it or put our probably just put our little electric fuel pump right
and then get it outside and see if she'll go in gear I guess. So now that we feel like we've got
everything pretty much buttoned up we're going to go ahead and push this jeep outside and see
if she's able to actually drive under her own power. Now on the carburetor we had to take a
little bit different approach. We were going to go ahead and rebuild this one but we just couldn't
get a rebuild kit here in time. So we ended up finding one that was pretty similar off of an old
AMC pacer. Pulled it on there and we've got it working great on that. Now on our transmission
we actually had to pull the top side of this shifter off. It was stuck in neutral when we
first found the jeep. Dad got it working where it would go from reverse to first but never could get
it into second or third. So I pulled it apart down here inside the transmission. It was super rusty.
Had a ton of water in there. So I cleaned all that out. Put some new gear lube up in there
and I think I have the transmission shifting the way it needs to be. But second and third are still
a little questionable there. Now as far as fuel goes we ended up using this factory new gas tank
that was with it whenever we bought it. Dad put a little piece of plexiglass over where the
pickup tube would be. So now we can see our fuel level and of course we capped it off with an old
spray paint lid for our cap there. So we're going to go ahead and try to give it a go. Like I said
all of the wheels are rolling. None of the brakes are locked up but also none of the brakes are
working. So not really sure what it's going to take to get those up and going. But we're just
going to try to hop into this thing see if it goes in gear and see if we can just kind of drive it
around a lot. You want to try and help me set this windshield down. I was afraid it'd fall but doesn't
look like it would have huh. Oh yeah. A little bit better view here. Let's see what she does.
See how she cranks. The transmission area. I'm surprised there's not more than just a rattle.
Yeah. There we go. Don't hit anything. Well she is moving.
I'm going to put a seat in here. It's hard to see up over all this
kind of seat for sure. I think it's as rough as a cob. Transfer case in high.
As fast as first gear is it's got to be.
So there is definitely some racket coming from that transmission or transfer case so.
Huh.
That old gear lube would get in there and work around real good.
Seats not though. I think I did pretty good. Yeah I'm definitely gonna have to get a seat though.
Got that little spot right there that kept poking me. I thought I was gonna bust the windshield out.
It was flopping around like crazy. Yeah. But yeah not bad. I never could get it in second gear. It
died on me when I got out there. There's something that's haywire inside that transmission. Right.
Like I said as rusty as that thing was in there that was terrible. Yeah I thought maybe just when that
gear oil would get worked around in there but we may have to tear into it a little deeper.
Right. Before we do got to make the victory lap though. Oh don't try to make it down to the shop.
Yeah it's not a victory till the end so. Yeah. Yeah we can try to make it down there.
Ain't no different any other one. No brakes but it seems to run better than most of the stuff.
Yeah. I think it's the first time we've ever tried to cut a donut in one. Yeah let's change
gopro batteries we'll try to make it down there. See if we can make her down to the other shop.
That transmission is noisy. Guys I think it's safe to say that we can mark this off as another
successful run around the shop. When we found this old jeep it had been abandoned for quite
some time now and we really weren't sure of why it was parked. As we got it back to the shop and
dug into it a little deeper we found out that the engine was just locked up solid in it. So
it wasn't in near about a shape as some of the motors we've been working with here recently.
Once we were able to get it to turn over well she just fired right up after that. So we're
definitely going to have to address this transmission a little bit deeper. It's
making some sounds that no transmission should ever make as well as address old
brakes on this thing. So all in all this was a cool vehicle to work on and we'd love to hear
what you guys would do with a project like this around your shop. As always be sure to like,
subscribe, ring that bell and we'll see you on the next one.
