DIY Camper Van to Travel AND Work | Van Conversion Part 1

Kis 7
35 followers
90 Video Views·Oct 20, 2022
I've been working a lot from home recently and that got me thinking.
If I can work from home I can probably work from anywhere.
So I bought a used cargo van and the plan is to convert it into an off-grid office
so that I can travel around my home country of New Zealand this summer
while still getting my work done.
So allow me to introduce my 2012 medium wheelbase high roof Volkswagen Crafter.
It has two doors at the back, one sliding door and nothing inside.
But what it lacks in interior decor it makes up for in surface rust and lichen.
But let's have few to me worry about that one because right now
I want to get the interior lining stripped out
so we can have a clear view of what we're working with.
The cab partition gets boot as well because that's going to give us a lot more usable space
and after peeling back the carpet and removing the old floor
despite the dust and the dirt everything's actually looking really good.
If I asked you to picture what a van looks like in your head
chances are you might think of a box on wheels.
Yeah they're anything but.
Every surface is curved, every side is different
and none of these shapes are nice square rectangles.
So what I'm trying to say is that taking accurate measurements to build off
yeah it's a real chore.
Now don't get me wrong I'm all for hard work when it needs to be done
but man this potential for a way to work smarter well...
So here we are in a program called Meshroom
and what it's done is it's stitched together all the 418 photos I took
into a relatively accurate point cloud using a process called photogrammetry
and after I've exported that out I've now got myself a 3D mesh model of my van.
Yeah it's got a few artifacts but from what I can tell from my reference marks
the main structure is within a few millimeters or so of real life
which is more than good enough at the planning stage.
In my extensive research on Instagram
I found the most common layout is a fixed bed across the back.
It's easy to construct and gives you an excellent utility area
that you can access from the rear doors like a car boot.
But I'm not going to do it that way.
This van is 1.8 meters wide and I'm 1.8 meters tall
and I don't want to have squished toes.
I could always turn the bed long ways but now the van is more bed than space
and I'm basically just driving a bed around.
So the way I've chosen to do this is to make a pullout sofa bed down the side here
so that during the day I'm not losing all of that space.
There's going to be a kitchen module on the opposite side
with a fold-out table going out the sliding door
and then I've got a ton of room at the rear here
for a large desk that I can comfortably work at
because that's kind of the point of all of this.
I'm also going to need an extraction fan here
and a small window on the side would be nice.
But before we do that I do need to deal with the exterior.
Honestly it's it's not that bad.
A little bit of gardening, a little bit of washing,
a little more washing, more washing, all right this is taking too long.
There's a couple of areas with a bit of surface rust
so I took them back to bare metal and gave them a quick repaint.
There's also a ton of little stone chips that are starting to get rusty.
This probably has something to do with the van being used
as a rally car support vehicle by its previous owners
because it looks like it's spent a lot of time on gravel roads.
But hey that didn't take too long.
Oh.
I feel like I should mention though despite the few cosmetic blemishes
the van itself is in good mechanical condition.
I took it to get a full service done the day after I bought it
and you know what they replaced?
The cabin air filter.
They didn't even need to do an oil change.
So I'm hopeful the effort that I put in now will be worth it in the end
and I'm not just you know putting lipstick on a pig.
All right everything's cleaned up now both inside and out.
It's time to start the actual build.
First on are the roof rails except they're not actually roof rails
they're lengths of unistrut
because you guys know how much I love working with slotted channels.
Ah the versatility.
But they're going to go into the grooves on the roof here
and these little circles yeah they're actually little caps
covering holes to go into the van.
So if I mark their location on the unistrut
then drill holes in it
the idea is that I should be able to bolt it straight on.
To get the caps off though I'm delicately extracting the retaining clips on the inside
then using a heat gun to soften the chewing gum they were apparently sealed down with.
I also made a bunch of rubber spacers
because the rail needs to clear the panel seams on the van so they actually sit flat.
Okay you ready for a recipe for a roof rail watertight sandwich?
First the sealant goes around the hole
then the rubber spacer goes on
then the rail
then more sealant
and finally the stainless steel bolts.
All right go ahead.
Pro tip you're going to need two people to tighten these up
unless you have really long arms
but if you get your helper to go up the ladder with the ratchet
all you have to do is stand there holding the spanner.
Yep.
Well with the roof rails on now I guess first thing in the morning
it's time to cut a huge hole in my roof and install the extraction fan.
Except it's kind of raining so I'm going to remove the headliner instead.
Look at that.
All right now for the roof fan.
Yeah it's still raining and this radio doesn't have bluetooth so
out you go.
I've got a new one with a reversing camera ordered but
let's come back to that because the rain stopped.
Okay so the idea with this roof fan is that you can use it as an extractor
to pull air through while you're cooking
or just cool things down on the inside with a bit of airflow.
It's got a couple of parts to it but for installation
the main one I need to worry about right now is this collar
which goes through the roof.
I also made this wooden support frame which gives the collar
something meaty to screw into
and doubles as a template for the hole I need to cut
which I centered over this very conveniently shaped part of the roof.
It's almost like Volkswagen had thought
people might want to add fans to these roofs.
Yeah nice one Volkswagen.
I lined up the frame with the four corner holes I drilled
and prepped for the cut by adding masking tape around the outside
so the base of the jigsaw doesn't scratch up the paint.
Then drilled holes for the blades to fit through.
Now I've cut metal a bunch of times with a jigsaw
but there is a special feeling of quiet terror
when you do it to the most expensive thing you've ever owned.
It's that little voice telling you that this is going to be
a real pain to fix if you did it wrong
but it was okay everything was fine
but with the rain rolling back in I called it quits for the day.
The next morning I opened it back up
and got to work getting the edges filed smooth and sealed with primer.
Once that had dried the collar could go on
which fit perfectly, kinda, not really
but it only needs a little notching so it fits over the ribs snugly.
There, much better.
I'm clamping the wooden frame and the collar together in their final position
and starting the holes off with a self-centering drill bit
before fully drilling through the steel of the roof and into the wooden frame.
My decorative frosting skills get some practice
and then the collar gets lined back up with a screw to hold it in position
while I fit the support frame from underneath.
Then it's all screwed down together
clamping the roof between the collar and the wood frame.
The edge of the collar then gets another full perimeter of sealant
because I'd really rather water didn't get in there
and a little trick I learned from a friend of mine who's a plumber
is that if you spray sealant down with soapy water
and then spray your finger as well it doesn't stick to you
and you can get nice clean edges.
With the sun getting low all that's left to do
is attach the actual fan unit to the collar with a couple of screws
and remove the plastic.
I can't really test it yet until I've done the power system
so let's move on to the next item on the list.
Again I've made a wooden support frame
and to get this to sit flat I'm going to have to remove this piece of bracing
which is a little tricky because I need to cut deep enough
but not so deep that I go through the wall.
It's also bonded with what looks like industrial hot glue
which after softening with the heat gun peels off in a very satisfying way.
From here the process was pretty much the same as the roof vent.
Mark the hole, drill through from the inside,
line it back up on the outside, mask up,
drill holes big enough for the blade to fit through,
start cutting it out with a jigsaw
and ignore the quietly screaming voice in the back of your head
telling you that you probably cut it in the wrong place.
But I hadn't except those smiles were short-lived
because my masking tape had developed a mild case of spontaneous disintegration
which led to one of the most frustrating hours of my entire life.
But we move on and with the edge of the steel all prepped
it's time to install the window.
I'm going to temporarily hold the support frame in with double-sided tape
while I lay a healthy bead of sealant around the flange of the window.
The install is probably easier with two people,
one on the outside holding the window and one on the inside screwing it in
but you know if you don't have any friends you can still make it work
despite being a klutz.
These windows are designed to go in caravans and motorhomes
which have much thicker walls
so having the support frame gives the clamping fixture
something to grab instead of just the thin middle of the van.
And for cleaning up the squeeze out it's the same trick with the soapy water.
So I've just installed the window and I was playing with the
latches here and just opening and closing it
and I noticed a wee bit of a problem.
So to the left here the seam, the seal is good.
We're nice and tight there.
But to the right the seam is less than good.
If you can see it there we've got a gap in that corner.
Now I can close it up with this latch
but I'm putting a lot of force on it
and there's a lot of bending happening on this latch
which I'm not a fan of.
So it's getting dark and I need to make a decision
whether I'm going to pull this window out and fix it
or just just live with it.
I pulled it out and nothing says fun like cleaning sealant off in the dark.
The next morning though I put my detective's hat on
to try and figure out what was going on.
Initially I just thought maybe it was the curvature of the van causing the gap
seeing how flat windows generally work best on flat surfaces
but after a few hours of head scratching
and running through every possible option I found this.
The double glazed window pane.
Yeah it was about as flat as a potato chip.
I contacted the seller and they agreed to send me out a new window
so after a few days this showed up on my doorstep
apparently having been mauled by a bear
and it was also the wrong size
so about a week and a half later
after finally getting an undamaged correct size window
I could finally finish installing it.
And after double checking the seals
check and check
we can call it done.
Ah that was a fun adventure wasn't it?
But moving on.
Before I start installing the subfloor
I need to do a little bit of prep work.
There's a bunch of holes going through the bottom of the van
from where the old plywood floor was screwed down
so they all need sealing up.
There's also a common issue with this type of van
leaking water through these panel clips
so they all get a good squirt with the gunk gun
and then any scuffs and bare patches get a coat of paint
to make sure we don't have any developing issues in the future.
I bought 12mm plywood for the floor
and while I technically only need three sheets
I bought a few extra
because if I don't I'm going to mess something up
and just end up driving back to the store anyway
and the subfloor framing is going to be made from these 2x4s
which I'm ripping in half.
A quick check to make sure I still had headroom
and then I started laying out the subfloor framing
because there's a chance it might meet moisture
I'm using treated timber
which here in New Zealand has dyed this lovely pink color.
It's a delicate balance
between putting enough structure in
that the floor doesn't flex
but not so much that you can't get a good amount of insulation in
so I'm going to try favour areas
that I know are going to have more weight over them
and then leave other areas more open.
I really don't want to put more holes
in the bottom of the van again
so I'm using a little combo trick
of super strong double-sided tape
and construction adhesive
to hold the battens in place.
I thought the old floor looked really good
so I decided to put that back in.
No I'm kidding
I'm just going to use it as a base for my new template
I mean why reinvent the wheel right?
I'm laying out the plywood for the new floor
so I can just trace over it with the old floor
and then it's just a matter of cutting it all out
before a couple of coats of finish
and while that's drying
let's jump over to the wheel wells.
I'd done a quick mock-up in CAD
so I transferred that onto cardboard
so I could double check that the fit was all good
and then I could use those cardboard panels as a template
to transfer over to the plywood
and finished it off with a few coats of polyurethane
there was still a little bit of time left in the day
so I jumped into a chore that had been bugging me for a while
someone was either trying to grow a terrarium
or nobody had ever cleaned under here
in the van's 10 years of existence
the next morning it's time to rip into the insulation
and I'm going to be using sheep's wool insulation
throughout this build
I mean I come from New Zealand right
what else would I use?
but no
obviously I did do a bunch of research
before deciding on that
and maybe that's a topic for another time
the roll comes standard for 2x4 framing
which is why I split it like that
and I found just snipping through with a pair of sewing scissors
actually made pretty short work of it
I say short work
but this actually took me like a good half day
to split trim and fit all these pieces
the floor is dry now
so in it goes
man I was having an absolute doozy
trying to get this floor panel in
but then I realized
I'd forgotten to cut the gap for the electrical conduit
that I'd run under the floor
so after doing that
unsurprisingly it went in a lot easier
where I'm going to fit the wheel well covers
I installed a wooden spacer block
and while the adhesive cures on those guys
let's jump over and fasten the floor panels down
I'd marked on the edges where all the floor battens were
so all I had to do was run tape between those marks
to get a straight line reference
for where the screws needed to go
yeah nice
and now the final task of the day
is to install the wheel well covers
by screwing them down to those spacer blocks
and also to the floor
yeah you know that feeling you get
when you're like
I'm forgetting something
but also it's the end of the day
so you're just like
I'm sure it was nothing important
yeah it was the insulation
I'd forgotten to put the insulation inside them
all right that's all I've got for part one
I am a couple of weeks ahead in the build
to what I have edited here
and man I can't wait to show you the next one
I'm going to design that pull-out sofa bed
and build a full off-grid electrical system
which is something I've been wanting to do for years
and I can't wait to share it with you
if you have any questions, comments, favorite sandwiches
leave them below
and if you want to help me appease the YouTube algorithm
a like and subscribe is very much appreciated
I'll see you on the next one
