Toyota Highlander Mechanical Review

The Auto Geek
46 followers
14 Video Views·Oct 18, 2022
Today we're going to be reviewing the Toyota Highlander. Now while most car reviewers would
praise the Highlander for its perceived reliability, but ding it because of its soggy
driving characteristics, we're going to be taking a look under the hood and underneath this
Highlander to see what's inside and how it works. Now we're going to start under the hood where we
have Toyota's tried and true 2GR 3.5 liter V6 engine. Now this is situated transversely for
front wheel drive and it's connected to an 8-speed automatic transmission that feeds an all-wheel
drive system. Now taking a look at the air intake setup here, we've got cooler that's going to
drain down through this tube here that feeds this air box which has the air filter and the mass air
flow sensor. Air is then going to travel through this tube here into the drive-by-wire throttle
body, then into a plastic intake plenum which then feeds into a aluminum air intake manifold
which will then bring air into the heads. And changing the air filter on the Highlander is
pretty straightforward you just got to undo a couple of tabs here and then you lift up the
air box and then pull out that air filter. Now with the air box removed you can see it frees up a
lot of space on top of the transmission as well as we can now see the drive-by-wire throttle body
and that plastic intake plenum. Now Toyota is still using its air acoustic induction system
powered by a vacuum switch which they've been doing for more than 20 years now. I do have another
video linked above if you want to see how that works but essentially it's got a flap inside of
here actuated by a valve which is going to change the air flow characteristics in this intake plenum
according to engine load. Now located right on the front valve cover here is your PCV valve
as well as the PCV hose as it draws air back into the intake plenum. Next we're going to take a look
at the ignition system and like many other vehicles it uses a coil-on plug design which
means that the front three spark plugs are very easy to access on this engine. However the rear
three spark plugs like with most transverse V6 engines are buried underneath this plastic intake
plenum which you have to remove in order to access them at the rear bank over here. Next taking a look
at the fuel system on the Highlander, what set Toyota apart many years ago was that they came up
with this dual injection system which means that this engine is both port and direct injected which
is going to yield not only more power and efficiency but you're not going to have carbon buildup which
is the deficiency of many other direct injected only vehicles. Now the low pressure pump in the
tank is going to bring gasoline up to the front of the engine here. We do have a high pressure fuel
pump which is located just behind this vacuum pump on the rear valve cover that's going to
pressurize the fuel and then bring it down to this fuel rail here which is going to directly
inject it into the cylinders. Now in addition to that we've got another low pressure line here
that's going to feed your regular port injectors which are located right here on the air intake
plenum before it goes down into the valves. That's what's going to be responsible for helping keep
those valves clean because they wash them off from any carbon deposits. Now looking at the oil setup
this does use a common 5w20 weight oil with your oil filler located right here and the dipstick
right up at the front here. Now taking a look underneath the body of the Highlander things are
fairly flat and covered up with the exception of the center section here for the exhaust. Now that's
a good thing because it's going to prevent salt water from splashing up on any vital components
during the winter and help a little bit with airflow at higher speeds. Now with those beauty
covers removed you can see you've got clear access to the engine on this side and the transmission
over on this side. Now underneath the engine here it's unfortunate that you still have to remove a
cover in order to do an oil change. You've got your drain port over on this side and then you've
got a cartridge style oil filter up on this side. Pretty easy to access but you might need a special
tool to unlock it. Now you'll see that this uses a steel lower oil pan that bolts to the aluminum
upper oil pan that ultimately attaches to the block. Now looking up underneath the front manifold
you can see this here is where the oil cooler is located. It's just a heat exchanger that draws oil
out from the engine and cools it off. You can see they have these two oil supply lines here that are
made of metal that bring oil out from the block on this side. Now in earlier 2GR engines these
oil lines were made of rubber and they would burst causing an oil leak. Now looking on the passenger
side of this engine bay you can barely make out the drive belts. You can see down inside of here
is where your water pump is going to be. Then up at the front here is the alternator and then down
at the bottom there's your AC compressor. This whole setup is best accessed from down below.
And here's a look at the drive belt setup from down below. You can see we've got the tensioner
located over here which is easy to change the drive belt but to get to the water pump once
again you don't have much clearance from down below here. Now from down below you've got this
little window here to access the timing tensioner. Now the alternator is located right up at the front
here and things are pretty tight to work at the front so in order to change that you're going to
have to remove the entire front assembly which means that you got to remove the bumper, the
bumper support, and the radiator in order to get enough clearance to get this guy out. And the same
goes for the AC compressor down below. Now more importantly just behind the drive belt setup is
your timing chain setup. That's right this has a timing chain which means you don't typically need
to service this over the life of this engine. Now those timing chains are going to drive both
the intake and the exhaust camshafts on the front head here as well as on the back head back here.
Now these here are the oil control valves that power the variable valve timing gear for both
the intake and exhaust side. Now in addition we do have your variable valve timing sensors that are on
the top of the bank here as well as the set at the back so the computer knows exactly where those
camshafts are. These engine covers aren't even plastic anymore it's all just made of sound
deadening foam. And now we'll have a listen to the engine. Next we're going to take a look at the
Now this is where I think Toyota's really shortchanged those who have to do maintenance
here. For example if you want to access the radiator which is buried down inside of here
you have to remove the entire front end of this vehicle including the bumper skin and the bumper
support in order to get that radiator condenser or the fan assembly out. Coming from the radiator
you've got this lower radiator hose that goes into this plastic assembly here and this entire
assembly is part of the thermostat. There's no separate thermostat like in the older vehicles.
Problem is in order to access this thermostat you need to get in behind here to access some
of those bolts to pry it off of the engine. Now the first step in Toyota's book to remove this
is actually to remove the entire transaxle assembly from the vehicle just because you
don't have enough space here. Now further to that is this is where the water pump is located
and because you have to remove that thermostat assembly and there's not much room to locate here
Toyota also makes you remove the entire transaxle assembly in order to get that water pump out just
because there's so little clearance. Now having tight water pump access has been a thing since
the 2GR engine came out in a transverse V6 orientation almost 15 years ago so you'd think
they'd either improve the access or make their water pumps more reliable. That's traditionally
been a weak spot on these engines. Now as for the rest of the cooling system here you can see the
radiator hose coming off on this side of the engine here and it goes into this plastic bypass tube
over to the other side of the V. From there it also splits off and goes inside of the cabin to
your heater hoses. Now a little bit more interesting is that those heater core hoses
actually have this bypass here that runs over to this side where it's got this auxiliary water pump
and here's a look at the cooling fan setup there's just a single cooling fan on the Highlander and
here's a look at that cooling fan setup from underneath along with the drain petcock valve.
Now the top here they do give you a radiator cap but it's a plastic extension off of the radiator
and then the hose that goes out to your coolant expansion tank. Now here's one thing I really
appreciate about Toyota sticking to an old-school design. Here you can see they've got a stamped
steel front subframe but unlike many newer vehicles not only does it tie the control arms together
over here and here but it extends back to the front over here straight up to the front radiator
support. So essentially you've still got a full box frame all the way around here that supports
the engine and everything underneath here as opposed to just being chopped off right here at
the control arms and everything up at the front here just being plastic. So here you can see the
lower radiator cradle also made of steel and it's also got this extension that comes off of that
subframe here and comes out to a lower bumper rebar over here that's to protect you from any
impact at lower distances in addition to the bumper rebar at the top here. So you've actually
got two separate bumper rebars protecting you and of course that steel radiator cradle continues
all the way up to the top and across the top and inside of here supporting the wheel well. Not a
lot of newer vehicles all the radiator cradle is just made of plastic and the only steel that extends
to the front is the single bumper reinforcement. Everything else here is plastic and there's no
front subframe reinforcement. Now while this design is going to be a little bit more heavier I think
it's going to be a little bit more sturdy especially in a moderate to low speed crash
because you don't have a lot of things to crumple under here compared to say plastic which is going
to instantly disintegrate. Now the front part of this subframe has even got one of these vibration
isolators that's made of rubber. Now taking out the Highlander's front suspension you can see
things are fairly simple here with the McPherson strut design. Now that bolts up to this aluminum
front knuckle here. You've also got your sway bar linkage over here that goes to the sway bar and
then over the steering rack. Here you've also got the inner and outer tie rod. Now this suspension
design is pretty much as simple as it gets. You have a stamped steel lower control arm here.
Replacing this control arm is pretty straightforward you just got two bolts that are easy to access
and your other frame bolt over here. Down over on this side of the control arm you have a bolted
on ball joint with that castle nut which means that you don't need a press to change out your
ball joint. Now one of the things I like about aluminum knuckles is you've got a bolted on
bearing so it's just four bolts and you could easily change that out you don't need a press
to change it out. Now while the McPherson strut design isn't going to be the best off-road
it's definitely a good compromise when it comes time to repair this down the road
because things are going to be pretty simple to work on and cheap to replace. Now taking a look
at the Highlander's rear suspension here you can see we've got a multi-link suspension design.
We've got a shock absorber located over here that bolts directly to the knuckle. You've got an upper
control arm here and then a rear lower control arm over here that carries the weight of the spring.
Now down around this side you've got a rather large trailing arm and then a front upper control
arm over here that ties into the knuckle. Now I think Toyota has done a little bit of cost cutting
back here because there's absolutely no aluminum. Everything here is made of steel including the
knuckles and even the subframe. Now a multi-link suspension design has become commonplace on a lot
of mid-size SUVs like this one because of its good handling characteristics. Now some brands
have executed it a lot better making it a lot easier to work on because it is quite a complex
design. Now Toyota for one has made some interesting changes to the typical multi-link setup.
Replacing the shock absorber for one is pretty straightforward. You've got a bolt at the top there
and a bolt at the bottom there and then inside of the lower control arm is this little stabilizer
link that connects to the sway bar that goes over to the other side. Likewise the coil spring is
also pretty easy to replace once you remove the bolt at the bottom here. However I think Toyota
could have done a little bit better in the placement of some of the fasteners to make it
easier to work on. Here's your front upper control arm and you've got the bolt located over there
right up against the subframe bushing. Now the manual actually calls for you to remove the entire
rear subframe in order to take this arm out and change it. Now that's because this bolt here has
to come out this way but it's going to clash into the subframe and on the opposite side you've got
the nut which they should have put the bolt on because it's much easier to access and remove it
this way and just put the nut on the other side. Now here's another look underneath of that front
arm and the clearance you have to deal with for that bolt. Suppose you could try to remove this
bracket here and see if you'll get enough clearance to take out this bolt without dropping the whole
subframe. Now for the upper control arm the situation is even worse. They also do call for
you to remove the entire rear subframe which would include the differential, any exhaust work and any
extra brake lines and everything in order to change this upper control arm in case these
bushings do wear out because the bolt is located over on this side and you don't have any access
here to get in with a ratchet or anything things are pretty tight. However on this side here there's
a little bit more space for you to fit a ratchet in so if they just plug the bolt in from this side
and weld the nut on that side you might be able to get away with replacing it without dropping
this entire unit. Now looking from underneath there you can see there is a camber bolt on the
rear lower control arm with a very interesting plastic cover here for aerodynamics and then here
you've got the other camber bolt on the front upper arm. Luckily though the rear trailing arm
isn't as difficult to replace with most of the bolts accessible. And here's another look at that
stamped steel subframe from underneath for the rear suspension. I like that they've capped off
these bolt holes here where your trailer accessory hitch would bolt in so it doesn't corrode. Now
while the front b-bar was made of aluminum the rear one is made of steel so they cut a cheap
back here. At least they give you a temporary spare tire and not a fix-a-flat kit. By the way this is
where the heater hoses and AC line goes in for the rear HVAC system. Next we'll take a look at this
8-speed automatic transmission in the Highlander. Here with the airbox removed you can see you've
got clear access to the top of it here with this plastic cover being your valve body cover. Now
just in front of that valve body you can see the two lines that come off and go to the transmission
cooler which is a separate unit from the radiator. Now the top of the transmission you've got easy
access to the starter motor which is just under this battery tray. You might have to be changing
this out soon if your vehicle's got the idle stop start system. Now something tells me exposed
copper isn't a really good idea because if I remember correctly copper is going to oxidize
over time. And just behind the starter motor is the cable linkage to change the gears and that's
because this has a cable operated shifter not one of those fancy electronic ones. Now what's missing
from this transmission is of course a dipstick which means that you can't check the quantity
or quality of transmission fluid that's inside of here as easily.
Instead they give you drain and fill ports with the fill port located off to the side here
plus access from down below. Now taking a look at the transmission from underneath once again you
can see the valve body cover and the drain port located over here. Now from underneath here if
you follow those transmission lines you can see it comes to the transmission cooler which is a
small separate unit off to the side here separate from the radiator. Now once the 8-speed automatic
transmission has done deciding what gear it's going to be it's going to send the power out to
this front differential and then over to this transfer case. Now that transfer case has got a
fill port up here and a drain port located down there because its fluid is separate from the
transmission fluid and you will have to service that after a while. Now the transfer case is going
to take some of that power from the front wheels and distribute it along this driveshaft that runs
down the length of the vehicle above the exhaust shield. Now that driveshaft is then going to come
to the back here to power this rear differential. Now what's interesting about this rear differential
on the Highlander is it has torque vectoring which means that not only does it bring power to both
rear wheels it can choose which wheel it sends more power to when you're powering through a
corner so that can help rotate the vehicle. It's a little bit better and more complicated than a
regular open differential slip and grip style system that you find in many other SUVs. Now at
some point you will have to change the differential fluid in here so you've got your fill port over
here and your drain port located down here. Now taking a look under the hood of the Highlander it
does have its fair share of electronics and wiring harnesses that are underneath the hood that run to
each of the sensors. Over here we do have your battery and this is where your computer is. Now
the computer is set back a little bit from the front of the vehicle so if you do get into a minor
collision hopefully it doesn't sever any of these wires although it does have this big wire down
here that runs through all the components. It kind of looks like a coolant hose pipe if you compare
the size. Now the fuse box on the driver side is pretty easy to get to and it's nicely labeled and
they also give you a fuse puller and some extra fuses but the real joke is the fuse box on the
passenger side. There is no fuses in here there's literally just two relays and two small fuses
and that's pretty much it. Makes you kind of feel that you should have ordered more options to fill
this fuse box up. Next we'll take a look at the exhaust now because this is naturally aspirated
we've got our front bank here that has an integrated manifold that goes directly into
this catalytic converter and then there's the same thing located on the back. Now that exhaust
is then going to travel down underneath the engine through this flex pipe and then join up with this
y-pipe with the exhaust that's coming off of the rear catalytic converter which is kind of an
l-shaped design coming off of the rear bank here. After the y-pipe it's then going to go through
another catalytic converter and then out the tailpipe to the muffler. Now that exhaust is then
going to travel to the middle part of the vehicle here where you've got your main muffler and then
it's going to travel out to this part here through a small little muffler and then out the tailpipe.
And now we'll have a listen to the exhaust. Now the Toyota Highlander has four engine mounts.
You've got one on the passenger side here and one under the battery on the transmission side
then up in the front here we've got this one here which is actually an active engine mount that
works with vacuum pressure. Now a lot more modern vehicles have switched to an electronic engine
mount. Now underneath the vehicle there's the rear engine mount which mounts to this steel subframe.
Next we'll take a look at the braking system on the Highlander. Now we'll start over here where
you have your master cylinder and it's got a small tank on it which feeds off of this much larger
tank and that's just because it's a little difficult to access underneath this windshield
cowl here. Now in and behind there you have a brake booster. Now that's vacuum powered but if
you follow that line it actually does not lead up to your air intake plenum. It's fed off of this
vacuum pump located down inside of here. It's actually driven off of the intake camshaft
on the rear bank. Now this is something you'd see in more efficient hybrid designs or turbocharged
engines where the vacuum in the intake isn't enough to drive the braking system but in this
case they did choose to do it even though it's naturally aspirated. Now the master cylinder is
then going to feed your ABS actuator located way down inside of the corner there behind this
auxiliary water pump. Now that ABS actuator is going to be responsible for your autonomous braking
features as well as your regular traction and stability control. I like that Toyota is using
its emblem for the front radar as well as these sensors up high in the bumper here as opposed to
down at the bottom here where it could be subjected to off-road damage at your local soccer field.
Now taking a look at the front brake setup on the Highlander, you can see we've got a dual
piston design here that drives a good size brake pad on this disc rotor. Now while on paper this
might be sufficient for the Highlander's size, now driving this particular vehicle with only 60
kilometers on the odometer I felt that these brakes were not really sufficient for the size
of the vehicle. It's almost as if I was towing another 5,000 pounds behind me. Now taking a look
at the rear brake setup on the Toyota Highlander, you can see you have a nice sized rear disc rotor
with your floating caliper design but they kind of cheesed out on the size of the pad. It's actually
pretty small here, something you'd find on like a Camry or something. You can only imagine when you
load up this vehicle with payload or maybe tow a trailer, I don't think these brakes are going to
be very sufficient. Now tagging along behind that rear brake rotor is this electric parking brake
actuator. Now luckily if you do have to do a rear brake job on one of these, there is a manual way
you can put in a Torx bolt here and unwind this. You don't need a special scan tool in order to
disable it. Now the Highlander has an electric power steering setup. Here you can see where the
shaft is going to come down to the steering rack which is mounted directly to the subframe. Now it
does use a rack mounted power steering motor located over here. Now usually these are pretty
reliable but if it does fail, you actually have to remove the entire transaxle assembly or maybe
just drop the subframe in order to get access to it. Now the fuel tank is mostly located underneath
the left side of the vehicle and it is made of plastic. Now overall I think the Highlander is
a good entrance to the SUV market especially with its proven 2GR 3.5 liter engine and a conventional
automatic transmission. Under the skin though I do have to take away points for having harder
to maintain items such as the cooling system and the rear suspension. It just gives you a lot of
extra labor for something that should otherwise be a lot simpler to replace. So if you're looking
for more of an old-school SUV I think the Highlander is an excellent entry, just make sure
you keep it rust-proof because everything underneath is all steel. Now make sure you follow me on
Instagram to find out what the next car review is going to be and subscribe for more videos
just like this one.
