Cleaning a Filthy Lexus GX470

Car Crease
237 followers
5 Video Views·Oct 18, 2022
What is going on everybody and welcome back to Mad Detailing.
Today's video is on this beautiful Lexus GX70 and this vehicle just
got back from a long road trip.
So now it's time to give it a nice deep cleaning and give it back to the owner.
And I know this vehicle is a lot cleaner than the cars you guys see on the channel,
but I promise you, we're working on some very nasty cars as we speak,
along with an extremely moldy boat.
So if you guys are new to this channel, make sure you guys like and subscribe.
I post brand new videos every Thursday at 12 PM Eastern Standard Time.
But with that being said,
we're going to go ahead and roll these before shots
and get right into this Lexus detail.
We're going to start off this detail with cleaning the wheels first.
I'm using our Xtreme APC on the tires and fender wheels.
And for the wheels, I'm using my Mad Detailing iron eraser,
along with multiple different brushes
so I can make sure I get every inch of this wheel and tire 100% clean.
So after getting all the wheels and tires 100% clean,
it's now time to move on to cleaning the paint.
I'm first using the pressure washer to loosen up all the dirt and debris.
And then I'll go ahead and clean the gas cap and the door jams.
And then I'll move on to foaming the entire vehicle down
with our Mad Detailing super blue soap and a foam cannon
before cleaning all the emblems with a soft detail brush.
And then I'll give the vehicle a nice hand wash with a soft microfiber wash mitt.
So after getting all the seats, the floor mats and the large trash
and debris removed, it's time to get this carpet a good pre-vacuum.
Now we'll get it ready for the carpet extraction later on in the video.
So moving on to cleaning the seats, I'm using our Mad Detailing
leather cleaner in a soft leather brush.
I'm not going to use the steamer
because I can tell that these seats have been dyed previously
and it's starting to come off.
So if you were to just grab a steamer or a harsh APC,
you're going to remove the dye and the customer is not going to be happy.
So anytime you guys are working on old leather or just leather in general,
so you just bought a car,
you want to inspect the seats very thoroughly before you move on to cleaning them
because over the years, I've had a lot of customers bring me their vehicle
that has been damaged previously by a detailer.
And they bring it to me asking if I can repair the seat,
you know, clean it and get the stain away.
And honestly, you can't because the dye is removed.
So the only way to fix that would be to re-dye the seat,
which you don't want to do that unless you have to.
So, yeah.
With that being said, just make sure you guys are inspecting everything you do.
And to protect these seats, I'm using our Mad Detailing leather conditioner.
And if you guys are wondering, yes, you can protect and use a leather conditioner
on seats that have been dyed as long as they were dyed properly.
So I'm not saying that dyed seats are bad because it has to be done
if the dye is removed or it's just an old seat.
But I mean, if you could avoid dying your seats, I would at all costs.
And moving on to cleaning the interior panels of this Lexus,
we're now using our Mad Detailing leather cleaner again in a soft detail brush.
Our leather cleaner is a multipurpose cleaner that can be used on all surfaces,
you know, services that aren't super dirty.
It is a powerful yet gentle formula that can be used on virtually
any service on your interior.
So if you guys would like to try our Mad Detailing leather cleaner
or any of our products, you guys can head over to www.maddetailingusa.com.
And moving on to the carpet extraction, we're using our Mad Detailing Extreme APC
as a cleaner, followed by a Milwaukee drill with a drill brush attachment.
For the extractor, I'm using my Mighty HP 60 hot water extractor.
And one tip that I can give you guys, if you guys are extracting the carpet
inside the vehicle, you don't want to just fill up a pump up sprayer
and spray it, you know, on there directly.
You want to try to use as less water and as less product as you can.
I know you guys have seen me, you know, saturate the carpet,
you know, in most of my videos, but I normally pull the carpet out.
But a quick tip is you use the hot water first from your extractor,
you know, just lightly mist the carpet.
Then you take a carpet solution, such as Extreme APC or pretty much
any APC on the market, and you want to just mist the surface.
You don't want to saturate it too much.
And then that's pretty much it.
Use your drill brush and then your extractor.
But that way you're using way less product and you're not,
soaking the carpet because this carpet does have a foam lining on the bottom.
So if you saturate the carpet too much, like when the carpets inside the vehicle,
they'll actually seep to the bottom and it will eventually cause mold.
So I want to use as least amount of water and product
as possible when extracting carpets inside of a vehicle.
So moving back to the outside of this vehicle,
the customer just wanted it washed and you really wanted the inside done.
But honestly, I can't let a vehicle leave my shop without doing some sort of polishing.
So the first step that I'm doing is I'm clay barring the entire Lexus
with a synthetic clay bar and our mad detailing clay lube.
And then we're going to give it a one step polish with a Rupes 21 polisher,
a microfiber finishing pad, and then we're also using HD speed.
And the reason why I'm using the microfiber pad is I'm going to get more cut.
So pretty much with HD speed, I think it's 3D speed now,
but pretty much it's made by a company named 3D.
It will cut, polish and leave a wax behind.
So the more aggressive pad that you use, you're going to get more cut.
But that doesn't mean go ahead and use an aggressive cut on a black vehicle
because you will leave a lot of micro marring behind.
But if you're doing a light color vehicle like this and using a microfiber finishing pad,
you will get better results.
But you always want to, you know, do test spots and make sure,
you know, you're getting the results that you're looking for
before you move on to the entire vehicle.
But this combination worked extremely well on this vehicle
with removing a lot of swirls and scratches and bringing out a high gloss shine
while leaving a good protection behind.
