Van to Camper Van Build Part 3 T5 - T6 Conversion Facelift

Mr. Auto
35 followers
19 Video Views·Oct 18, 2022
Hi guys welcome back to the channel. So as you can see we got a lot of parts have arrived in.
We've all the parts now for the T6 conversion, the headlights, the grille, the bumper,
all the parts we need. Also I got in the grey carpet for the inside. So we've a lot of work
to get going with so let's get started. So the grey cloth I've been waiting for to come has
finally came in. I got a couple of tins of adhesive there as well. So now I'm going to
get going with starting to carpet the sides. I've pretty much measured out roughly what I
think the length is and I'm going to show you a few tricks for laying out by yourself.
So let's get started. Okay so the first thing I need to do before I start to glue on the carpet
is to drop down the roof lining. Some people reuse this lining when doing a conversion but I prefer
to make my own from plywood as it is a stronger job and it's easier to mount custom lighting
and also easier to carpet as I make it from one entire piece. I've taken a couple of measurements
of the side I'm going to be covering here. If you're doing this covering by yourself it's a
good idea to get a couple of magnets to help hold the cloth in place while you're working.
I've used two vice grips to keep the carpet held up while I'm working on it. Okay so I've laid the
carpet in and I've spent a bit of time making sure that there's plenty on the top, plenty on the
sides and plenty on the floor as well because the last thing you want to do is you want to run out
of material in a certain corner. There is no perfect way of doing this. I've done a few of
these. There's not really a perfect way you can do them. You just have to start in one corner and
then work your way around making sure trying not to get wrinkles in it. Wrinkles are probably the
issue you'll have with this stuff but it's not too difficult to put on. It's just a bit time
consuming but I'm going to make a start at it now. I'll probably start over in this corner over here
and we'll see how it goes. Okay so I'm about halfway through now. With the majority of this
back panel done over here it's pretty much tacked in fairly good. No wrinkles nothing like that.
This panel here I've pretty much it done as well. I've pretty much a lot of the top half done
and now I'm down to this wheel arch section here which I find is the hardest section to do.
As you can see we already got a crease coming on just up here but I've left myself plenty of
material over so I'm not going to run short of material or anything which is the problem I've
had before where I've left it short and then with all the curves and that you actually run short.
So I've loads left over so it should be fine. So I'm going to tackle that bit next. Hopefully it
goes good for me. I'm using a high temperature heavy duty adhesive. This is an exceptionally
strong air solid spray adhesive especially formulated to withstand exposure to high
temperatures but the good thing about it is it takes 10 minutes to cure so if you make a mistake
you can pull the carpet away and then reapply it which is very useful if you get a crease or
wrinkle in the carpet. Okay so I've got the carpet trim pretty much well stuck on there now. I've
left it a little bit long in places. I'm just going to go around and trim off the a lot of the
excess. I'm still going to leave a little bit over maybe about two inches over just in case I need a
bit of extra at some point. So I just took delivery of the glass for the sides. Now I'm going to go
ahead and fit it into the van. That way it'll be waterproof and I can push it outside and stuff
because there isn't a lot of space in here. So I'm going to go ahead and do that right now.
I've cleaned the surface where the window will bond to the van and then used a black primer
specially designed for glass. I've applied the window bond so it stands about 10 centimetres
tall from the bodywork. When applying it to the bottom of the window try and keep as close as
possible to the cut edge so it doesn't leak out the bottom when the window is pressed on. Offer
the window up as level as possible. Try and press the top and bottom at the same time. You will
still be able to manoeuvre the glass a little to get it into the exact place where you're trying to
make sure the gap is the same all the way around. I'm continuing on with the carpet covering on the
left hand side of the van as once the carpeting is fully complete I can screw down the floor
and be finished with that. Okay so more than halfway through done on the carpet line of this
side and it's starting to look really good. I always like to leave a little bit of extra all
the way around just in case I need it. On areas like this here what I like to do is just get a
scissors and just put a few cuts in all the way around. That way it makes it a lot easier to tuck
into the corners which probably the most difficult bit as you said is doing these arches.
They're quite hard to do but what I do is I mostly do the flat part first and then I make my way
out. A bit like laying vinyl I think. I always kind of, to me it seems like it's a bit like laying
if you ever lay vinyl on your car or anything like that. It's quite similar but I'm getting
through it there now so just a matter of finishing off the little bits that are hanging out and
that should be this side pretty much done.
So I finally got all the pieces to finish the T6 conversion on the front of the van.
We've got the headlight second hand, the grill a second hand, these are actually original
headlights and original grill. I managed to get the body panels brand new, the bumper is new as well
and the grill for the bumper is second hand. So I'm going to bring in the van now and start
stripping it down and getting ready to fit everything on. I think it's going to be quite
a tricky process to get everything fitting really nice. There isn't much information
online about doing these conversions so I'm just going to have to take it step by step
and figure it out as I go along. So I'm going to bring in the van now and start stripping it down.
So pretty much most of the front end stripped off. I have stripped off a few of these before
so I do know where all the bolts are hidden which makes it a lot quicker process. Now I'm
going into a bit of the unknown with the fenders. I've never taken the fenders off any of these
before and obviously I need to remove these to put on the T6 fender. So it should be fairly
straight forward. I don't need Volkswagen to make it too complicated. So I'm going to get
cracking with the fenders there now. Ok so I've everything completely stripped off the van there
now. I'm going to start with this fender and this headlight in this corner here. I'm going to make
my way around just making sure all the gaps are good. Everything should be a straight enough fit.
I know these headlights are genuine Volkswagen headlights so they should fit fine and the
grill is genuine as well but the fenders these are aftermarket so hopefully I won't have any
issues fitting them. But we'll see how it goes. Ok so I've got everything on. Everything looks
like it fits fairly good. The gaps along the headlights are good. There's a couple of good
points and bad points with doing this conversion. I'm going to need a lot of plastic clips here
for the bumper. The mounting point is different on the T5. It's up here and it's got 10 bolts
whereas this is a clip system so it clips in. Also the thing I never thought of is the square
plastic piece that goes here. These are the T5 and they're way off. They're a lot different so I'm
going to need to order that as well. I need to order down here. Also I need the repeater
indicators. They're different as well. The mounting points and the headlights, the top
two bolts are the same. I'm going to have to make mounting points at the bottom of the headlights
but everything else fits pretty good. The bonnet fits fairly good. I haven't tried to see there's
a lock just yet but overall I'm pretty happy with everything so far. Obviously I have to do
a really good fitment on everything. Make sure everything fits really good and locks really good
and then I'll rub it all down and I'll get ready for paint. There's one more thing I want to show
you guys before I finish up this video real quick. These are the mirrors that are on the Transporter
T5. They're actually a really ugly wing mirror and I just never liked them so I went ahead and
got the T5.1 wing mirrors or T6 mirrors and I've banged them on now just to see what they look like.
Okay so I just put it on there to show you guys real quick. It's a far nicer looking wing mirror
I haven't really screwed it down or anything like that because it's actually primed so I'll end up
colour coding it which will be even nicer again. So I'm going to leave it there guys. I hope you
enjoyed the video. We got a lot done there today. I've got a lot of the carpet line done. The big
one was I got this T6 front on pretty much on and it looks really good. Once this front has
been on it's really transformed the van. It's going to look even better when we paint it white
and we get the spoiler and stuff on. I hope you guys will join me in the next video which should
be in about a week or two. I'm working as fast as I can with this getting parts is a little bit slow
but I hope you guys are enjoying the series and I'll see you in the next video. Thanks for watching.
