1975 Oldsmobile 98 Regency: Gothic Luxury In a Transitional Year

RC- Car
12 followers
AI Generated·May contain errors
1975 was an interesting year for the Olds 98
as this would represent the penultimate year for
this huge body style.
And 1975 was also what I would call a transitional year for the styling
of this Oldsmobile as Oldsmobile started migrating
the front end in particular to begin to look
increasingly like what would come out in the 1977 model year
when these full-size vehicles
would be downsized, but this was definitely not a
A downsized Oldsmobile.
In fact, the 1975 Oldsmobile 98 would represent
the longest Oldsmobile that's produced in
the modern era, and it would measure 232 inches in overall length
and ride atop a 127-inch
wheelbase.
So this vehicle was just eight inches shy,
actually less than eight inches shy of being
20 feet long.
That is absolutely enormous.
Now let's take a look a little bit at some
of the styling features of the 75 Olds 98.
And like I said, it's kind of a strange transitional year.
This admittedly is not my favorite front end of the Olds 98s,
but it's got some, well, interesting features.
The first thing that you notice is that the typical egg crate grill
from the Olds 98s has been modified here to have kind
of a rectangle within a rectangle theme.
And this really stood in sharp contrast
to the 98 front ends that came before it,
including the preceding model year, the 1974,
that had, I would call it, a more divided grille.
That split grille theme was something
that would become a part of Oldsmobile's design DNA
after the 1968 model year introduction of that split grille.
And the 74 Olds 98 had an even wider split between the...
portions of the grill and had an egg crate theme similar
to other 98s of the era but here like I
said you've kind of got the rectangle within a rectangle
and even within a rectangle theme so
a little bit of dimension to that overall grill.
Now 1975 was also the first year for the square
headlights and it's kind of a strange front end
because you have the eyebrow over the headlamps
I don't know what you want to call it
but that header panel clearly has a raised section in the
And that's kind of round and so is the overall front end has quite
a few rounded forms associated
with it coupled with creases.
But you have these square headlamps and as time would go on
the 1976 would migrate to a more squarish front end.
And then of course in 1977 when the car was
redesigned you had a very square front end as well as a boxier car. So
You can kind of get a sense of how designers
were evolving the front end year by year.
Remember, each year the styling changed
on the Oldsmobile as well as other vehicles.
And they eventually progressed to a design that would stay similar
for a number of years once they got to 1977.
Now, as we rotate around to the side of the car,
we'll notice this vehicle has the optional cornering lamps up front.
There's a rather large cornering light.
Those were introduced for the first time in 1962 on Cadillacs
and at this point they were becoming
relatively popular across vehicles.
You can also see the five mile an hour bumper in the front and
how far it hangs out. A massive bumper,
almost like a battering ram on these vehicles. And then
you have a body side theme that was characteristic
of Oldsmobiles during this time frame and that was
the skeg lines. Now here you have the skeg line kind
of starting in front of the front wheel
And then it folds into the wheel arch
or kind of outlines the wheel arch, if you will,
which is fat at the bottom
and kind of tapers a little bit as it gets toward the top of the wheel
and then fattens again as it moves rearward on the car.
And then you can see the skeg line continuing down
the body side where it continues to the fender skirt
and then up over the rear portion of the body side.
This again was a theme that Oldsmobile had
on a number of vehicles whether it was the 98
or the 88 and I suspect it was perhaps a bit
of a variant on the 1966 Tornado theme.
Although it was clearly different Oldsmobile
was still trying to accentuate
its wheel arches and here they just took
a different form more of a squircle style shape.
But again, this was an Oldsmobile bodyside theme
that they had for a number of years in the 70s,
and it also even appeared on the Cutlass,
where that vehicle had some very distinctive skeg lines.
Now, aside from the skeg lines,
this vehicle displays a number of characteristics of GM
vehicles of this era. First of all,
the toothpick A-pillars with the semi-wraparound windshield that
was characteristic of all GM full-sizers.
And on the four doors, you have the hardtop design here.
No B-pillar. That little thin metal piece
is just attached to the rear window glass.
And you have a six window upper,
You have the rear quarter glass on either side.
This was a typical form that was displayed
on the GM vehicles of the era.
They all used that same windshield, the A-pillars,
the front glass, the rear door glass.
I think they even used the same quarter glass, the rear quarter glass.
But the sheet metal below the belt line
was different, completely different,
whether that was the fenders or the doors or the rear quarter panels.
As we rotate around to the rear view here, you can see that
Rear quarter glass and then the relatively thin C-pillar.
Something always bothered me about that
rear quarter glass. It just doesn't look like it's
at the right angle relative to the rear door glass
and the C-pillar. Well not my favorite let's just say execution
of this particular design. I prefer
the earlier model years that didn't have the glass in the C-pillar
but the C-pillars were rather
chunky and this was a functional solution.
You can also see how sharp that skeg line is in the rear
Coming off of the rear door and then basically
coming down and forming the lower portion of the fender skirt before
completing its form on the rear quarter panel.
Now notice behind the rear quarter panel you have
these fender extensions
here that are a different color which was very typical because
they had to use a different paint I believe.
that was able to flex on these bumper fillers
and so oftentimes you'll see those as being cracked
or discolored and they are expensive to replace.
The replacements are not generally good fitting
and you're going to spend a lot
with a body repair shop trying to get them to fit correctly
but no you know that's something that if you want one
of these old 98 Regencies of this area you're
just going to have to put up with but look
at how big that fender extension is.
That again was for crash standards. That's why you have the big bumper
and you have those gothic style taillights
that we'll take a look at in a second
that are so far away from the actual sheet metal
of the quarter panel such that that
area could collapse in the event
of a five mile an hour impact in the rear.
As we rotate to this other side,
you can see the gothic style tail lamps, kind of the element that
I named this video after. Oldsmobile 98s had
these vertical tail lamps ever since the 1963 model year
and I believe they were really just trying to emulate Cadillac
and a lot of the upper end
General Motors vehicles of this era had vertical tail lamp cues
or vertical cues in the rear.
Again, because they were trying to emulate Cadillac,
who had the vertical-style tail lamp in many years,
or at least a very vertical-style rear quarter panel form.
I do enjoy the...
Tail panel here and that rubber flubber piece,
that's also an extension that's beneath the
reverse lights and the little,
I'll call it running lights underneath where it says Old 98.
There's this rubber panel on either side
and that often cracks and degrades and
it just ends up looking like crap.
So it's just something to be aware of when you buy
one of these vehicles. Like I said,
that will cost you a lot of money to replace.
Thousands of dollars, maybe two
to three thousand dollars minimum, perhaps even more now.
This is also a pretty simple car from a surfacing perspective,
but it's very clean and it has some subtlety.
Notice the body side here has this kind
of concave surface before going convex
and has a really nice bone line that runs the length of the car
with a relatively subtle radius to it.
And that's about it, aside from the skeg lines.
If you wanted to describe this car, you would, say, have a door that...
comes out extending away from the window wraps
into a bone line and then
Kind of tucks in beneath a lower skeg line.
That describes the body side of this vehicle.
And here we'll take one more look at this side profile of the Olds 98.
Look at that rear overhang.
This was an era of rear overhang.
Remember, this car has a 127-inch wheelbase.
This is a long, long wheelbase.
But you'll also notice a very GM trait here.
You've got that roofline with the very slight droop
to it as it moves rearward.
And then you have the C-pillar kind of aligned with the rear wheel.
Again, another very GM-y trait.
Not quite sure why they did that.
Probably, I guess, just for aesthetics.
Yeah.
But, well, it looks good.
The rear overhang does look a little bit cartoonish
with those fender extensions, though, I must say.
Now let's switch to the interior of this Copper Canyon Old 98 Regency,
because this is where it gets especially interesting.
This is the 1975 Olds IP. It was redesigned for the 1974 model year.
Before that had more of a
driver-centric theme to it. Here it still has a little bit of that.
You'll notice that some of the
gauges or I should say the radio
and the barrel vent above the radio are rotated toward the driver
but it's much more subtle than it was in 1971 to 1973.
You also have the crotch cooler vents there
And the...
steering wheel below the steering column
and below the glove box something that
you don't see on cars anymore did help circulate air
and make everybody feel
cool when the air conditioning was on.
Speaking of air conditioning this car
has Oldsmobile's Tempmatic system
this is no longer Comfortron in other words
the Comfortron would control the blower speed
the outlet air location as well as
the outlet air temperature here Tempmatic just controls
The outlet air temperature
and the driver is responsible for setting the fan speed,
which has a switch off to the left,
as well as the mode, which is the slider bar up top.
So it got less complicated and was a cheaper setup.
I think customers actually tended to like it better, too.
Some didn't like that they couldn't control where
the air was coming out on the Comfortron setup.
You also notice this car has relatively thin
air conditioning vents these barrel vents
but they work just fine because remember this car
was running R12 freon for the air conditioning
which was icy icy cold so didn't require
as much airflow today modern cars require so much airflow
in part because the outlet temperature
is not as cold that's to some degree by design
but it's also just a consequence of some
of the newer modern air conditioning systems.
And here's the best part of the interior
in these 98 Regencies, and that is the seats.
Now, notice the button-tufted,
loose-cushion style design that you have here in the 1975
Oldsmobile 98 Regency, which really was initiated
with the 1972 Oldsmobile 98 Regency when Oldsmobile
division manager John Beltz asked his chief interior designer,
Blaine Jenkins, what could
he do with $100 incremental dollars in the interior?
And so the interior designers came up
with these button-tufted, loose-cushion seats.
A similar theme on the door panels that you can see there as well.
It was an over-the-top style theme,
and actually these seats aren't overly comfortable, amazingly.
They look very comfortable,
but the foam is a little bit too hard on the back.
Of course, now the foam is, let's just say,
older, 50 years old, pretty much.
But still, the seats are, I would say, comfortable,
at least compared to modern-day seats and standards.
And this is what really sold the car.
In fact, the 98 Regency was a limited edition in 1972,
and then it became so popular it was offered on the 98,
and the interior was offered in many different colors
as opposed to just black like it was in 1972.
But, yeah, this is kind of why you buy one of these vehicles
Sofa-like interior and you'd probably
also buy it for the rear seat that you see here which
was quite spacious. You got the rear armrest
and like I said by this point you had the rear
quarter glass so it was a very open
and airy cabin in these and also because of the tumble
home of the car it's pretty funny there's
so much space between the seat back and the door.
Uh, that you can kind of pass things back and forth,
uh, in between, uh, it's just a
function of how wide the car is at the middle
and how relatively narrow it is at the top.
And that was all done for looks just to give
the car the overall look of width, but yeah,
the rear seat passengers also sat in comfort and they got these big.
Pockets in the back of the front seats in case they wanted to put maps
or something else so they
could be official backseat drivers.
And now we turn under hood for the next to last year for
Oldsmobile's 455. Notice that the decal
no longer says Ozmobile Rocket 455 like it did in earlier
years. I guess because engineers thought it was no longer the Rocket.
Womp womp. By this point
455 was making just 190 horsepower.
It did make 350 pound feet of torque. That's not all that much
by modern day standards. I would say if you drive one of these,
the engine is just sublime though.
It's so smooth and velvety and quiet,
just whisper quiet that, you know what,
the 190 horsepower doesn't matter that much.
It's got plenty of low end grunt.
And you'll see a couple things in this engine bay.
The cruise control servo there up front.
This is an Oldsmobile V8.
One of the ways you can tell is that oil fill cap in the front.
Other GM divisions did have the oil fill caps in the front,
but by this point, it was really Oldsmobile that did that.
And notice the braces that run from the cowl over to the fenders.
This would be the last year for them on the 98.
In 1976, it was the same car, but they eliminated those braces,
likely as a cost-saving move.
Now, interestingly, the holes are still there,
so you can go and get a set from a 75, 4, 3, 2, 1.
Old 98 and put them in and you'll get
a little bit better structure on your vehicle.
These cars do have quite a bit of quivering to them.
They were designed to have flexible frames.
And the thought was that the flexible frame would just absorb
the road shocks and would provide a better ride.
And I have to say, in some cases it did.
Some cases when I've driven these cars, they do ride extremely well.
And in other cases, they're very jiggly.
It just all depends upon...
The body assembly, and they were subject
to relatively considerable variation, especially
given that the build quality during this time frame
for General Motors vehicles was not
all that great.
But the engine and transmission,
the turbo-hydromatic 400 transmission in these vehicles was just
a sublime powertrain, absolutely bulletproof, reliable, quiet.
The only thing that it just wasn't great at was fuel efficiency.
If you drove it on the freeway, you'd get 14,
15 miles per gallon at 70 miles an hour.
Not too bad for a three-speed automatic
and 50-year-old technology with a carburetor and
clearly an un-aerodynamic shape.
But in any case, that is the story
of this 1975 Oldsmobile 98 finished in Copper Canyon.
Let me know if you like this and put a comment in the comment section.
Thanks again for watching.
