Stay tuned after the teardown to see a 15min TRC Evo Race Compilation! In this episode, we link up with Jay Meagher from RS Garage for an exciting teardown of the legendary TRC Sequential Evo’s engine! Built by Ronnie Crawford back in 2007, this 4G63 powerplant has been through more than 17 years of action -- It’s incredible to see how well it’s held up after all these years of abuse! Stay tuned, as we uncover the history of this impressive engine. We’re excited to share this moment with you, and we hope you enjoy the journey just as much as we did! Drop your thoughts in the comments, and as always, thanks for watching! #thatracingchannel
What's up guys, Javier from That Racing Channel. Today's video is a special one for the TRC
family. The TRC Sequential Evo is one of the most iconic cars in our channel's history.
In today's episode, we're tearing down the Ford G63 that's been in the car since 2007.
We're here with Jay from R's Garage to see what kind of shape it's in after all those years of
abuse. We've raced this car hard over the past 17 years with over 26,000 miles pushing around
1,000 horsepower, thousands of street pulls, and hundreds of races. We believe this to be
one of the longest running 1,000 horsepower Ford G63 engines of all time. This Evo has been such
a big part of TRC's history and we're so excited to share this moment with you. So let's see what
we discover throughout this engine teardown. Hi, I'm Jay from R's Garage. Today we're going to
take apart this Mitsubishi Evo 9 engine. Now this isn't just any Evo 9 engine, this is the engine
out of TRC Evo. Now this engine was actually assembled back in 2007 by a gentleman named
Ronnie Crawford. And I had the luxury of meeting Ronnie Crawford in the early 2000s because he
built an engine for me for my Mustang and we got to have a fair share of conversations. And Ronnie
is passed on now, but he was a man that was sought after for his work. He was from the old school.
He put a lot of attention to detail and tried to share his wisdom with you to keep you out of
trouble as a racer. So it was a really neat experience to work with him and it's a neat
experience to have what I would consider the longest running test case of low compression
versus high compression because this engine makes a minimum of 34 pounds of boost. At a minimum,
they generally run it at 45 to 50 psi and it's been alive this entire time. So the head gasket
had been changed once. They created some coolant pressure while racing it at a half mile event
years ago. They put a head gasket on it, some fresh for a valve train at the time, put it back together,
traded hands. My brother owns it now and it started to gum up a spark plug. So the engine's
at the end of its life, but a lot of people like to say, you know, that engine knows me nothing.
Well, this engine has been together tons of run time, tons of fun time, and we're going to peel
it apart, examine some components, and see if we can find some of the old man's tricks. So come along.
So before we get the timing belt off, for those of you that aren't savvy on the 4G63, this is kind of
evolution of the Evolution engine. The early ones were fixed intake cam, fixed exhaust cam timing.
This has a MIVAC system so it can advance the intake cam. It's got a fairly unique trigger
pattern. So it's got this optical hull sensor and very few teeth. Most modern triggers are like
60 minus 2 or 36 minus 2. A lot of teeth on the crank trigger. And this is a fairly simple
four-tooth program, four-cylinder engine. And I tried to make sense of it in my head. I assume
something about maybe processor speed back then, because this thing is rooted in the 90s,
and keeping track of the crankshaft, maybe a keep it simple stupid type approach,
is what they were doing with that crank trigger versus a high tooth count. Because processors
weren't that advanced and if you're going to have knock control and boost control and a bunch of
things integrated that were basically rooted in the 90s, maybe that trigger pattern was what they
selected. It has both a mechanical adjustment for the belt tension and a hydraulic tensioner. So
it's a combination of these two devices that yield the right tension on the timing belt.
This engine also came factory with a balance shaft that's been deleted,
which is an interesting talking point. This engine has a larger than stock stroke crankshaft
at 94 millimeters versus 88 millimeters. So Mitsubishi, when they developed the engine,
they put a balance shaft in there. What that's going to do is balance the engine by canceling
some of the harmonics that are naturally occurring in the rotating assembly. This
little idler down here is remnants of the factory balance shaft system. Otherwise it has a oil pump
drive by the timing belt, and then just this idler pulley, an adjustable cam sprocket on the exhaust
cam. But again the real star here is the variable intake cam, because when you advance that intake
cam during spool up, you widen the power band by getting the turbocharger online sooner.
Some of the things that kept the 4G63 alive during its career as a OEM turbocharged engine
is a fairly robust cast iron block. It has a lot of airflow available. If you look at the
ports on the cylinder heads, they're big ports. You have rocker arms and hydraulic lash adjusters, so
compared to something like a 2JZ where you have a camshaft lobe that's swiping a bucket,
you're lift limited at that point because you don't have a rocker arm that's multiplying the
lift. So you know rocker arm could be 1.5, 1.6, 1.9 ratio, and that really promotes a lot of
valve lift that you just don't have present on a cam on bucket type arrangement. You also have
the opportunity to be in an OEM turbocharged chassis that has a cooling system that was
designed to manage the heat present from a turbocharged engine. So if you go back into
the Honda realm, none of those cars were engineered as OEM turbocharged vehicles,
so they almost always had a deficient cooling system compared to the Mitsubishi Evo that had
all these roots in rally racing, endurance racing, things got this big radiator on it,
factory oil cooler, things that'll help keep the engine alive longer. Now one thing that they did,
which was a super good move, is a higher capacity oil pan. You have a wet sump oil system.
Once the engine speed is high, the oil is just foamy and frappuccino looking, and it's hard to
good quality liquid oil keeping the bearings alive. So anytime you can add oil capacity,
you're adding oil life. So this has an old school AMS oil pan on it, which is going to hold a quart
or more oil, and that's going to help keep that alive because as that foam is on the top in the
oil pan, you have more liquid oil present down at the oil pickup ideally. But the best way of
ensuring that there's liquid oil available is adding capacity. Whether it be a dry sump system
or a wet sump system, oil capacity is always your friend. So you have a couple things that are really
working towards keeping this engine alive. Aside from the lower compression ratio, which we'll
talk about more in a little while, just the fact that it's an OEM turbocharged platform,
and it had OEM engineering in terms of cooling, airflow, it just loans itself to being what it is.
I mean this is why these DSM platforms and Evo platforms have made so much power for such a long
time. Its roots are in the late 80s, but for all that time we were able to have so much fun because
of a lot of this OEM engineering. Probably one of the biggest single takeaways that we'll get out of
this engine is the lower compression ratio. You have to kind of imagine what the engine is going
through when it's running, and the compression ratio is the first heat source. So when you're
dealing with a modern vehicle that has a set boost level, like a modern OEDI turbocharged engine,
it's got a relatively high compression ratio because they have really good control over
low speed combustion with the direct injection. And they are able to get away with a high
compression ratio because they're, while running fairly high boost levels for a factory pump gas
unit, they're managing combustion really well and they're helping the catalyst live a long life.
In the realm of what we are doing in the aftermarket, we're trying to have the most
amount of fun for preferably the longest period of time because it costs a lot of money to break
your stuff. And one of the things that I dealt with with Ronnie when he worked on my engine was
he really was stuck on a low compression engine for me. Because he said you know you're going to
win some races, you're going to lose some races, but you're not going to lose a race because you're
missing 30 horsepower. You're going to lose a race because you spawn or you miss the gear
or this or that. And you know he explained to me this dance of compression ratio and boost and
heat management. And basically when you have a low compression engine, you have a very wide timing
window. So the engine will run at a lower timing number or run at a higher timing number. And
you're walking down essentially like a road that's around 15 feet wide. And as you raise
the compression ratio, you narrow that road you're walking down. And you can get into engines that
have a narrow window between not detonating and detonating. And you know say if you had a
seven and a half to one engine, you're walking down this big wide 12 foot wide road. And if you
had a 10 to 1 engine, you're walking down a road that is maybe four feet wide. And then if you go
into 11 to 1, 12 to 1, stuff like that. Higher compression ratios that should really only be
for methanol fueled engines, not gasoline or ethanol fueled engines.
On gasoline or ethanol, you'll end up with a very narrow margin. And it's fairly unrealistic
to think that the engine's going to live a long life with a very high compression ratio
because it's going to be knock prone. And it may not break right away, but you'll take the engine
apart and you'll see the signs in the in the bearings and in the pin bores. Maybe you're
bending rods. You know there's different in every community of engines, there's different types of
failures. The Coyote guys will bend rods. Honda guys will crack blocks. Some of the super guys
were able to crack OEM 2JZ engines and that's just from detonation. So when you're going through the
process of building an engine, that last 20 or 30 horsepower that you'll yield from a higher
compression ratio, it's not a zero cost to you because the engine lives for less time. So an
engine like this, which it's terribly lazy off boost, I mean it has 85 psi of cranking
compression because it's a low compression engine with big cams. And when you listen to it idle,
it's just not happy at a very low speed. But when you get it up on the pipe,
it has a big margin of error. And if you look at the timing map out of this car,
you're talking about timing numbers in the high teens and low 20s where a regular Evo may have
zero degrees at peak torque and 11 degrees or 12 degrees at high rpm. The engine is way more
timing tolerant and that gets into a whole voodoo of crank angle, combustion time, when do you light
the charge, when can you maximize the force of the charge on the crankshaft to give you the
most amount of power output. There's a lot that goes into it. But for the common guy that's just
trying to have a good time, maybe we should reconsider low compression engines. You know,
if you blow your car up twice a year, it's a few months at a time to fix it. Thousands of dollars
to fix it and you're not having any fun. And sure you're in this process and maybe you're going
through it for the first time and you haven't gotten tired of blowing it up yet. But if you're
starting off and you're like, well, I want to make 1000 horsepower, maybe you make 1000 horsepower
and you don't make 1060 or 1050 because you just build a low compression engine. And you get to
have more fun with that engine over the years. This engine is presenting itself to us as you
can have a lot of fun with a low compression turbocharged engine, because it just lives well,
you know. So something to consider, especially if you're a two-wheel drive,
your traction becomes the biggest obstacle, more so than power output. So, you know, the Evos are
special because they're all-wheel drive. Like I asked my brother the other day, could it use
more power? And he says, yeah, it just doesn't really spin. It's hard to make it spin. So he
has a condition that's way different than, say, me with my Supra. My Supra won't eat much more
than 1000 horsepower on asphalt with the tires it has, you know. So it doesn't make sense to
ask for another 100 horsepower because I can't use it until I'm going over 100 miles an hour,
where this platform has got so much traction, it could eat it. But we're still not going to
change the compression ratio. They told us that it's like seven, eight to one, which is around
where the 1G Mitsubishi engine was. And if those of you that were around for the 1G, you could
tie the wastegate shut on your 1G Eclipse. And if you had a Kometic head gasket on it,
you could just have fun. It just wouldn't break because it didn't have enough cylinder pressure
and enough heat to pick at it versus a high compression engine. For those of you that have
had a high compression turbocharged engine, it doesn't take much to kill it if the tuning is off.
And again, it's different with methanol because methanol has the ability to remove so much heat.
Methanol is like coolant inside the cylinder versus gasoline and ethanol. They just don't
have that ability to suck the heat out of the program the way methanol does. So most of us that
are going to be running ethanol or gasoline, lower compression is a strong consideration,
should be a strong consideration over maximum power output. So the head studs that are
successfully holding the head down with 45, 50 pounds of boost, Hobby said they've run as much
as 60 pounds of boost. This is an ARP custom made 625. The 625 material is a fairly new material
to the market. It has a 37% more strength than a 8740 fastener. And in this application, it has
a bullnose. So you see this long area here, that's going to bottom out in the block. That keeps the
stud from turning as you're installing the fastener and torquing it. So the bullnose bottoms in the
engine and now that stud can't turn anymore. So you could focus the effort during the application
of torque of the fastener and just clamp force and not rotating the stud. Not all engines can use a
bullnose. There are engines that say right below the last thread of the head stud is an oil galley.
And if you put a bullnose on it and it's able to turn in there, you can crack
the block into the oil galley. So not all engines get a bullnose, but this is a pretty nice fastener.
The custom made 625 also doesn't have any corrosion issues. L19 can get into hydrogen
embrittlement, which if you read about hydrogen embrittlement, it's pretty fascinating. Water
attacks the fastener in a way that under load, the fastener will just break. Whereas the custom
made 625 is just not a problem. It's also not a problem with the common 8740 fastener, but in 8740
you give up that, you know, 37% more clamp load, which you need it when you're running this much
boost. So, you know, if you're looking at fasteners and you're going to buy fasteners for an engine
that's going to see a lot of boost, the 625 is more expensive, but it's cheaper than changing
the head gasket after it's been running. This is very much how early turbocharged engines looked.
You have a minimal amount of crown around the ring set because you need to have material around
the ring set. You can't, it'd be impossible to move the ring set so far down in the piston.
So you have this crown area around, but this big fishbowl is doing nothing but slowing the
combustion down. So it would be hard to make this engine detonate. When you have an engine with a
flat top piston and you look at like an in-cylinder camera of detonation, it always kind of happens at
the fastest parts of the chamber near the quench pads, where when that piston's coming up to the
head, there's so much speed of the compression of the charge that it loses control and it detonates.
And you get into a big bucket, just a big bowl piston like this, it's really hard to make an
engine like this detonate. So this is another good talking point. Once the multi-layer
steel gasket came onto the scene, there were three-layer gaskets. And when you got
into OEM turbocharged or OEM supercharged, those OEMs went to five-layer and seven-layer gaskets.
So the reason being is you have a chunk of iron and a chunk of aluminum and you're trying to
squish the gasket sealed with the minimal amount of deflection.
And five thin layers of a gasket are easier to squish flat than a thick steel core and two
outer layers. So when you get into gasket selection, if there's a higher layer count gasket
available for your turbocharged engine, if you're using a multi-layer steel, always opt for the
higher layer. So whether it be a minimum, it's going to be a three-layer, but the five-layer
is going to be better for gasket sealing. Some of the later model GM stuff is seven-layer
and it just allows these thin shims to get very flat without a lot of deflection because the
least amount of deflection on the deck in operation is going to have the best gasket sealing because
you only have three or four thousandths worth of movement before the gasket will start to leak.
So when they had this engine at a half mile event years ago, they were able to make some
coolant pressure. And what they're doing is they're exciting that cylinder head and that
block enough that it's opened up past that three or four thousandths amount of sealing.
And then you get into pressurizing the cooling system. And once you get past that point,
now you're torching. And if you've ever seen the insides of an engine that had a multi-layer
steel gasket that torches, it is destruction. So you don't want that. But if you're shopping for
gaskets on your turbocharged engine, the higher layer count is worth your while.
There's a reasonable amount of just water present in the cylinder. We're down here in
Florida. The place is a swamp. The ethanol fuel basically draws the water in. So whenever you
have an engine that's running on ethanol, it's less of a problem on pump ethanol because pump
ethanol has some gooey gasoline stuff in it, whereas race ethanol is a very dry fuel. So if
you're using a race ethanol for periods of time, it's not a bad idea to fog the engine if it's
going to sit for periods of time or use some sort of top end lubricant. It's not nearly as harsh as
methanol in this subject because methanol is really, really dry and you'll create a lot of
corrosion in bores with methanol. It's very corrosive fuel. Ethanol is kind of like really
splitting the gap between gasoline and methanol, but there's some shadowing in the bores and some
pitting in the bores that just the thing sits, you know, when it lived in South Florida, a lot of
water in the air, you know, some of that ethanol down in South Florida, the pump ethanol, you could
actually, it actually kind of smells like water in the fuel and that's because there's water in the
some of this stuff here. It's not terrible, but it's just an age thing that you you've got to
deal with when you're using an alcohol-based fuel. But no heavy scuffing on these two
cylinders at least. Number four was the trouble cylinder. So what he ended up doing was, Tim was
putting the spark plug in this thing every once in a while because it was fouling that plug. So we
should be able to see more deterioration in number four than the other cylinders. Another thing that
Mitsubishi 4G63 had really going for it was oil drain back. So all of these big holes in the engine
block are to aid in oil returning back to the pan. So you have a bunch of oil being pumped up
to the top of the engine and the crankcase pressure is trying to leave the crankcase
and try to escape out of the valve cover and there's just traffic. And if you have an engine
that has inadequate drain back and crankcase pressure, the oil can get trapped in the head
and then it will deplete what's in the pan and then the engine will burn up. And the modular,
the early modular Ford engines were notorious for this and the RB26 guys actually put external
drains to drain oil back to the pan. And a lot of aftermarket engine builders will also add
drains to the cylinder heads to return oil back to the pan. But Mitsubishi was ahead of that
problem on this and they have a lot of drain back available because those big holes,
these big holes that you see in the deck, if the holes are small, the crankcase pressure is coming
up, the oil is trying to go down, the crankcase pressure will carry the oil out of the engine.
And those engines are the ones that you get a lot of oil in a catch can, things like that.
Well Mitsubishi, with these big holes, it just allows room for the traffic. So
crankcase pressure is coming out, oil is going back down, oil pan stays replenished,
oil pressure stays adequate, engine continues to live. So this is just a
fundamental advantage you have in an OEM engineered turbocharged engine.
There's some assorted stuff in the oil pump pickup. Looks like some silicone and then
some towel or rag, paper towel shreds probably, and a little tiny piece of metal. This little
guy right there. That guy came from somewhere. Now this is fun, the oil pan was extremely tight
to the engine but the oil pump pickup tube is not. And that's a paper gasket that will
compress over time. But when you're installing an oil pickup tube on an engine that has a paper
gasket, make sure that you use the torque specs because as that gasket compresses,
the bolts will get loose and looser and looser and looser. And if you have an oil leak between
the pickup and the oil pump, you're not going to be picking up oil any longer
and you'll kill an engine. There's also another bolt missing here, the one that supports the tube.
It's not there unless it was here because this bolt was in the bottom of the oil pan but
this one looks like it's freshly fallen out and this one's just not there. But
the oil pump pickup tube has a support bolt on it because the amount of vibration that's in the
engine, if the oil pump pickup tube is not supported, it will likely vibrate, crack,
fall off in the engine and then you're back to not picking up oil. So this is the windage tray
and what this plate here is trying to do is keep oil that's in the oil pan cavity away from the
parts that are spinning. Because when you pick up the oil, not only does the oil have weight,
which a lot of people get all jazzed up about having their pistons balanced within a gram,
well I mean oil weighs something so as it's splashing around in the engine you're
picking up weight. So this windage tray is scalloped to evacuate oil to where the engine's
spinning and it's trying to spit the oil out of the rotating area back down into the oil pan.
Second piece is a crank scraper. This is shaped specifically so the crank throws counterweights
and the connecting rod can pass by it and all that oil that's just in motion will hopefully hit this
drip onto the windage tray and go back into the oil pan. So these are two things that are done
in an attempt for better oil control because of the engine RPM. So another neat thing that
the 4G63 has is this integrated girdle. So this piece that I'm touching is also the main caps.
It's all one piece. This wasn't present on the early 4G63s. This is a seven bolt and later
approach and not only do you have now integrated the main caps in one piece but you're sharing the
vibration that's going on in each main cap into this part. So this is a pretty neat piece. It's a
big chunky piece and we'll get off the car and look at it some more but again OEM turbocharged
engineering you know like this evolved into a bed plate design. The bed plate engines are
stronger than this design but this is what they were doing you know to keep these engines alive
and keep them living and keep them managing all the power because even in its delivered form
Mitsubishi needed to have an engine that could be raced successfully in an endurance environment
and this is one of the steps they took to make that happen.
So with the pistons on the bench there's some stuff that's becoming evident.
This has free movement and I can reach in there and rotate the pin with my fingertips
and everything's free and clear. Then the other three are sticky so you have bent pins.
When the pin bends it then won't rotate in the bore of the piston and eventually will tear itself
up or tear itself out. So this engine has three bent piston pins. The piston pins are a fairly
thin wall at 150 thousandths. This isn't something we would do today. One of the things you kind of
have to understand about piston pins is the material is all fairly similar. So if you buy a
set of Wiseco pistons or JE pistons or Manley pistons the material is the material. It's a
surface hardened pin that the manufacturer or engine builder will either ask for a longer pin
depending on piston design or they will ask for a thicker pin a thicker wall pin to try to add
material. Now the way to make that even better is if you move to something like a Bill Miller
engineering pin or a trend pin where the pin is now through hardened and what that does is it
gives the pin a better memory. In operation during operation the pin may bend but it will likely go
back to its original shape versus a pin that is just surface hardened like this pin. Once it bends
it stays bent and you'll start to get into some material transfer which you can see it and feel it
on this pin and again the other pistons don't move freely. So where this one will just flop
back and forth this guy is stuck. So you got bent piston pins. The ring gap on the top ring
was right under 30 thousandths of an inch and the second ring was 32 thousandths. Now that's
going to be something that a lot of you may feel some kind of way about because it's a fairly big
number. It's about ten thousandths bigger than what a regular 85 or 86 millimeter bore would get
but the ring can never butt and when it butts is when the ends meet because the ring gets overheated
because you messed up on your tune-up and the rings touch and then the ring bends and now the
engine's wasted. When you have a big ring end gap like this not a lot of bad happens. This engine
wasn't puking copious amounts of oil into the catch can. There's much more damage from corrosion
in the bores that would promote blow-by than the ring gap itself. You guys may think that that's a
bad move but it's a great illustration of showing that when the gaps are big nothing really bad
happens. When the gaps are tight the ring can deform and bend and then you've got to take the
engine apart. You know the manufacturer recommendations are minimums so when you look
at the ring gap minimum that's a minimum value. As you gain experience you may open that clearance up
and again not much goes wrong from that. There's a couple things going on as we move into the bearings
but they're mainly going to be focused on the crankshaft. The crankshaft is an eagle
crank. They were unsure of what the crankshaft was because the person that had sold it had
labeled it as a custom but it's just an eagle crank. When you look at the journals on the rod
journals you can see that there's actually more wear present on the bottom side of the journal
than the top side of the journal. Part of the crank that's seeing the combustion
as the piston pushes up the bore to TDC and this is the side of the crank that's just returning
the piston back down the bottom to the center. Look at the wear difference on the top versus
the bottom. Do you see the scratches and the discoloration? That's oil flow and this
crankshaft doesn't have direct oiling so the oil enters the crankshaft through these two holes
across the journal and then it travels up and it tries to exit the crank rod journal
horizontally basically and the oil gets trapped because of the centrifugal force of the engine
At low engine speed the way that this crank is drilled is fine. At high engine speed the oil
gets trapped in the crank so a crankshaft like from Brian Crower that has direct oiling is a
good move and without any real debate about it you can just look at the crankshaft and see that
even though there's not as much load present as the piston goes back down the bore the oil's
depleted and the oil can't keep the bearing and the crankshaft separated so that's something that
may be changed because of the nature of the vehicle. This vehicle spends a lot of time between
5,000 and 9,500 rpm so having proper oiling is a good thing. The center main has lost its crush
so this bearing has failed. This is a really neat topic because a lot of people are under the
assumption that what's holding the bearing in place in the engine is the tang on the bearing
and that's not correct. The tang is there to locate the bearing during the installation of the bearing
the crush of the upper bearing and the lower bearing meeting in the housing bore and being
pushed against the housing board so it holds the bearing in place. Yes this bearing has lost
its crush but it's because it's failed so when you look at the surface of the bearing it's given up
and it's given up in the center main because the crankshaft is whipping. It's changing shape
in operation which is power level, it's stroke, it's material, and it's probably just time to go
to a different crankshaft for the use. Even though the the crankshaft has lived a long time and the
engine's lived a long time if you are looking at something and trying to improve it you wouldn't
put a crankshaft back in that's seen this much fatigue work because every time it moves it's
it's being worked on a very small level so you keep working a part back and forth eventually
it's going to break but you can see the damage on the crankshaft main from it whipping and the
bearing crush is gone so this bearing still has crush. I have to push it down into the shell and
I move it it's tight this one has lost its crush it's closed up so that thing is junk
but this problem isn't a bearing it's not the bearing manufacturer's fault this is just a use
so you have an engine that makes you know over 250 horsepower per piston it's got over 25,000
miles of use when you drive a car like this it's because you're making rips you're not driving it
because it's fun to drive around the trans is noisy it's laggy off boost you know it's got a
lot of personality it's a car that you take out you do some rips you go back home you relish in
the access to have a toy like this and you know just live in the smiles but these parts have
have done a fair share of work over the years so one thing that we'd consider is when we get the
main girdle back on without the bearings in it is you'd measure that main tunnel and see if this
main tunnel is larger than the other tunnels because when you get into that about a crank
whip it's working the material around the crank it's working the block so you want to make sure
that you have a control of the bearing housing because control of the bearing housing and
control of the crankshaft is going to make the most consistent uh hydrodynamic wedge of oil
that's riding on that crankshaft keeping the bearings from touching down on the parts
which is what we have here if you look through either the rod bearings or the main bearings
they've all reached their service life so again they don't owe anybody anything but they've
definitely reached their service life but this one was on the way out this is where people get
into saying a spun bearing and it doesn't spin with force it spins because it closes up
and when it closes up it no longer has anything holding it in the journal and enough material has
worn away from the face of it that then it can start to turn but it doesn't uh it doesn't spin
because of a tang problem it spins because it's it's collapsed the bearing it's worn out it's
reached the end of its life so as you look at the cylinder head deck you can follow the path
of the sealing ring of the head gaskets and there was no combustion leak so the cylinder head gasket
was not leaking it is worth noting on the 4g63 due to the valve size and valve angle when you're
timing this engine it's important that you don't just rotate the cams because the valves can hit
the valves and they'll bend slightly and then shortly thereafter you'll have a valve train
failure a catastrophic failure so when you time a 4g63 you want to be careful that you're not
running the valves into the valves it's one of those engines not only a piston the valve concern
but a valve the valve concern as well now forgive all the gunk uh the kind of this
discoloration the film that's just from the oil that's being used what you're want to be focused
on is you've got a chilled cast cam it's a kelford 280 and then you have this roller rocker arm so we
talked about it earlier but you have a roller rocker arm which is going to give you the opportunity to
run more valve lift and then there's a small hydraulic lifter on the 4g63 that will act as a
cushion rather a rather than be a solid valve train like on a honda so the valve train is pretty
forgiving and pretty good on the 4g63 also in terms of serviceability the head hardware is
independent of the camshafts so a lot of important engines you have to take the camshafts out
to get the cylinder head off this one you don't you can take the cylinder head off you need to
service the gasket because keep in mind the origins of this engine were in the composite head gasket
days so if you were around for the 1g eagletown eclipse they were just the head gasket was the fuse
instead of you hurting the bottom end or hurting the head you just push a head gasket and the way
the valve train is arranged you can quickly pop the cylinder head off change the head gasket go
back to having fun and as the engine evolved in the multi-layer steel head gasket evolved
kind of like took away that fuse to some degree but in the terms of longevity
those early 1g dsms they had kind of the writing on the wall as far as what you can get away with
again being a low compression engine now low compression doesn't come without a cost
the engine doesn't run as well down low and uh it doesn't have that pop it's not as crispy it's not
as snappy it's not as efficient so it does make for a a bit of a doggy engine off boost again this
engine has you know 85 or 80 pounds of cranking compression when you get into an engine that has
200 pounds of cranking compression there's a bit of snap and you'll feel it at that low speed
but at high speed when the turbocharger is doing the major influence on how much power the engine
makes the lower compression just makes it easier to make the engine live at the end of the day
really neat case of a low compression engine you know uh 25 or 26 000 miles of just
taking rips i've driven this car before it's really uh uh once it gets on the pipe and you
start pulling that lever it's a really really neat ride just just as fun as fun can be um so
the car definitely serves its purpose and the compression ratio and camshafts and tuning and
everything loan itself to be a pretty reliable vehicle so we're going to take these parts to
the machine shop we're actually going to follow this engine all the way through the machining
processes so if you want to tag along for that process we're going to try to answer the question
of what happens when you drop your engine at the machine shop what you should expect and what each
step looks like and uh the machine shop that's going to do the block work has a very technical
hone that will actually be able to see the deformation of the cylinder over time because
the even though it's cast iron big heavy chunk the boost in the stress they it changes the shape
of the components over time so it'll be a neat opportunity to follow this engine through the
rebuilding process back here for assembly back into the car appreciate you watching this video
hopefully you learned something or it was interesting at a minimum uh if you do enjoy
this type of content come over and watch my new channel it's rs garage uh just kind of getting
things going but we have a pretty good thing going on and i'd appreciate your support thanks and i'll
see you next time
ac on hey look it has all the seats in the car nothing missing better luck next time on
oh
one two three
190 it's weird i don't know what happened god dang this thing went 190. yeah but look ac look
hold on now wait a sec it's a custom shifter that i put on it
not six shift that's awesome man
oh man that's a rush isn't it oh my god
so
terrified
you