10 Bushcraft knife skills in 10 minutes

Campings
152 followers
#survival #bushcraft #outdoors #fire skills #Lifestyle
The bushcraft knife. Arguably the most important tool in the backpack.
Some are cheap, some are expensive, but all of them serve a purpose.
A typical bushcraft knife has a Scandinavian grind with a full tang, which means the steel
runs the whole length of the knife, all the way to the back of the handle.
Now, we call them bushcraft knives, but really they can be used for pretty much any task in
In this video, I'm going to show you a number of different skills you can do with the bushcraft
knife. Some you may have seen before, others not so much. Either way, cheers for tuning in
and I hope you get something from this video. For many of the bushcraft shelters that I build,
I always try to peel the bark off logs to help prevent bugs from eating away at them,
and to prolong the life of the timber framework. For this, I would normally use a tool called a
draw knife or a bark peeler. This tool has a very specific use, which is to peel bark off trees,
or to taper the ends of pieces of wood to make wooden pegs or chair legs for furniture making.
However, when you're in the woods, you might not have this type of tool with you.
Instead, you can make your own draw knife by gently tapping the point of your bushcraft knife
into the end of a small stick. You can then use one hand to grip your knife, and the other hand
to grip the stick. And you now have a makeshift draw knife, which you can use to peel the bark
off logs. The back of the blade of a bushcraft knife will typically have a 90 degree spine to it.
This gives the edge a right angle, which can be used for a number of tasks. One of which is to
strip the outer layer of tree roots. For this, I grip the knife upside down and place a root between
the solid surface and the back of the knife. Then I apply some downward pressure onto the tree root
and pull it towards me. As I pull the root, the spine of the knife strips the outer layer clean
off. This gives the root more flexibility when using as cordage. You can also further split the
root down using the point of the knife to make it more pliable when tying knots. Another reason why
a bushcraft knife has a 90 degree spine is so that it can be used to strike sparks from a ferrocerium
rod when used to light a fire. Here is a typical ferro rod. This particular one comes with a small
flat piece of metal which can be used to strike sparks from the rod. Not all fire steels come with
these. Now you could use the actual blade of your knife to do this and it would work well, but you
will end up dulling the blade and reducing its cutting ability. What you could do instead is
rotate the knife upside down and use the 90 degree spine of the blade to strike sparks from the ferro
rod. This way you can still protect the blade from damage. Another tip when using a ferro rod and
knife to start a fire is if you are too aggressive with the knife you can end up knocking your tinder
material everywhere and in wet conditions this can affect your ability to light a fire. If you keep
the hand that holds the knife in a locked position you can then just pull the ferro rod back to
produce sparks. This way there is no forward movement with your knife which reduces the
chances of you knocking your tinder everywhere. The flint and steel is a very traditional fire
lighting method. When done correctly it is an extremely satisfying way of lighting a fire.
You hold the steel striker in one hand and the flint in the other and hit the two together
producing sparks which can then be used to light some tinder material and get a fire going. If you
look closely the steel striker actually has a very similar edge profile to the spine of a bushcraft
knife both around four to five millimeters thick and with that acute 90 degree angle. If you don't
happen to have a steel striker on you you can use the back of your knife to create sparks from the
flint. You have to be extremely careful how you hold the knife as the blade is facing towards
your hand. I always ensure that I have a really firm grip on the blade and in similar fashion to
the steel striker I bring the back of the knife down hard onto the sharp edges of the flint
to produce sparks. If I slow this footage down you should be able to see sparks coming off the
back of the knife. It's important to note that the sparks are not pieces of flint
but actually pieces of hot metal from the back of your knife. So for that reason and of course the
reason of safety I recommend not attempting this technique and using another easier method to light
a fire. I'm just showing you what can be done. Despite only having a thin cutting edge in
comparison to an axe you can still split fairly large sticks with your knife. Just place the blade
across the middle of the stick and batten down on the back of the blade to drive it into the wood.
Once the knife blade is through the log keep battening down towards the tip of the blade and
eventually you will split it. It's a fairly safe method of splitting a log and you can actually
split logs down to very fine kindling for fire lighting. In wet climates lighting a fire can be
tricky and finding dry wood can be very hard. A good way of getting decent firewood is to split
open logs to expose the dry inner pieces of wood. You can then use your knife to shave off thin
pieces of the dry inner wood. These are called feather sticks and if you make the shaving fine
enough they could ignite from the spark of a ferro rod. However there is another way of making
feather sticks. If you put the point of your knife into a log you can then pull the piece of
wood towards you to make thin curls. This method means that you use very little energy and you can
be much more precise with how thin or thick you want the curls to be. This next skill can be done
with pretty much any knife. I use this skill fairly regularly with my pocket knife to make holes in
pieces of wood. I put the point of the blade onto a piece of wood and gently rotate the knife in a
half circle. Each time I rotate the blade I am taking away more material. Eventually you can
rotate the knife enough that it actually bores a hole straight through the wood. In this particular
project I used the knife to make some holes in a round piece of wood and then I put some points
on three sticks and inserted them into the round wood to make a stool. One of the most common uses
for a bushcraft knife is to make notches in sticks. Here I make a simple pot hanger. I start out by
gently battening the knife into the stick at diagonals making an x shape. I then carve away
the material up towards the stop cuts that I made making sure I do the same each side. Eventually
the shape of the notch starts to look like the beak of a bird. This is often called a beak notch.
The other end of the stick is just a fork shape and now I can hang this fork on a horizontal stick
over a campfire and then the beak notch I just made can be used to hang the handle of a kettle
over the fire. The bevel of this particular knife is ideal for making deep slicing cuts.
In some cases you can cut small trees or saplings where you would normally use a saw.
I only tend to do this technique on very thin saplings or thin branches on trees. For it to
work it needs to be on a green tree and not a dead one. Bend the sapling and put some downward
pressure on it then make a slice cut at 45 degrees to the branch. You do need to apply a fair amount
of force into this cut but by bending the sapling it helps to split the cut more. Sometimes you can
get a clean cut through the sapling first go. Other times it might split in two and then you
need to do the same technique to the other half to make it cut. Another handy skill for this type
of knife is cleaving a branch in half lengthwise. With a branch this long you can't batten down on
it to split it. So if you make an initial split in the end of the branch using your knife all you
then need to do is twist your wrist to open the cut more and split the wood further down. Each time
it splits move the knife further down the branch and twist your wrist again. And there you have it
10 quick bushcraft knife skills that you can do when out in the woods. One very important point
before we end the video. Be careful when using any knife or sharp tool. Make sure that you have a
well-stocked first aid kit and do not attempt any of these skills if you are new to using knives in
the woods. I wanted to show you some of the knife skills that I use on a regular basis when practicing
bushcraft and outdoor skills. I recommend getting yourself onto a bushcraft course that focuses on
knife skills and safety. There are some excellent courses and instructors out there who can teach
you the safe ways to use a knife in the woods. Thanks for watching and I'll see you in the next one.
