富士山を閉じ込めたアクセサリーの作り方 / レジンでふじさんを作る方法

maaue resin channel
22 フォロワー
11 回視聴·2024/12/25
Hello everyone, this is Maaue.
Today, I'll show you how to make a cylindrical piece with Mount Fuji inside.
You can make it even without a cylindrical mold. The steps aren't too difficult, but there are a few key points to keep in mind.
I hope you'll carefully follow along with this explanation while watching the video footage of my process!
First, prepare any suitable mold for coloring and use masking tape to remove any dust.
Let's pour in the resin.
This amount should be enough for about three pieces.
I used blue and white coloring agents, but I thought adding a bit of green might make it look prettier, so I added a small amount later.
Color it slightly darker than you think. That way, Mount Fuji will stand out more and look beautiful.
Use an embossing heater to warm the resin and remove bubbles.
Once you've removed most of the bubbles, place it in a spot away from light and let it cool for a while.
Use kneaded eraser to make clouds. If you don't want clouds, feel free to skip ahead to 2:57.
Prepare a small stand.
Take a small amount of kneaded eraser and knead it well.
Flatten it and gently place it on the stand.
Something like this is fine. Set it aside for later use.
Get some card sleeves. These are fine if bought at a 100-yen shop.
This time, I'll use two of them.
Cut off the edges.
It should be fine if you end up with four pieces in total.
Prepare some cellophane tape and pre-cut a few small pieces.
Fold back a little bit of each tape piece so it will be easier to peel off later.
Attach tape to the edge of the sheet.
Roll the sheet from one end to form a cone.
Attach another piece of tape to the edge of the sheet. Fold the end slightly so you can remove it easily later.
Trim it to make it smaller.
Attach tape to the inner edge of the sheet to form a clean cone. This makes the following steps easier.
For this tape, don't fold the edge. Use it as is.
Take another sheet and cut it slightly smaller than half.
Prepare tape with folded edges.
Roll the sheet from one edge to create a cylinder.
Roll it about twice and then secure the edge with tape.
Now the cylindrical shape is complete.
When you insert the cone, the tip should stick out slightly. That would be perfect.
Cut any leftover sheets into narrow strips.
Roll them up.
Place them inside the cylinder. Repeat this two more times.
This is the cylinder made with four narrow sheets. It's a pretty clean shape.
Like with the cone, attach tape to the inner edge of the sheet.
The cylinder is now complete.
You'll have one extra sheet left, so you can make another piece or use it for another project.
Prepare a flat mold. Any mold's backside should work fine.
Also, prepare white resin and pour a small amount into the cone.
Carefully pour it in so that the white resin doesn't touch anything other than the tip.
Add about 4–5 drops and cure it.
Once it's mostly cured, you're good. Now, let's pour in the blue resin.
Placing a mold underneath prevents resin from leaking or overflowing from the tip.
Once it's cured, peel off the sheet.
If there are holes or dents, apply resin to fix the shape.
Cut off the tip using nippers.
Use a file or a design knife to smooth out the cut edge.
Prepare a flat mold.
Pour a small amount of clear resin.
Place Mount Fuji on top of the clear resin.
Cover it with the cylinder.
From the side, adjust Mount Fuji to make sure it’s as centered as possible.
Pour clear resin until it reaches the height where it covers Mount Fuji.
Prepare the flattened kneaded eraser and place it into the resin.
Adding 2–3 small chunks should be just right.
After adding the clouds, carefully remove small bubbles.
From the side, adjust the cloud placement. They tend to sink slightly while curing.
Position the clouds a bit higher for a balanced finish.
Change the angle of the light as you cure it thoroughly.
Once the curing heat has cooled, remove it from the mold and peel off all the sheets.
It’s starting to take a nice shape.
If there are any dents, apply resin to fix the shape.
Add resin carefully to make the cylinder as clean as possible.
Once the shape is reasonably clean, trim the excess using a file.
In the video, I used a design knife, but a regular file works just fine.
After removing most of the excess, use a finer file to smooth it out.
This step isn’t required, but it helps create a smoother coating, so I recommend it.
Attach the eye screw.
This time, I matched the shape of the eye screw directly, but if needed, use a pin vise to drill a hole.
Use a stick and double-sided tape. This tape is from the 100-yen shop (Daiso).
Cut the tape into small pieces, attach it to the end of the stick, and fix the cylinder to it.
Prepare clear resin and start coating the curved surface.
It might be easier to use a brush to spread the resin evenly, but I used a stick in the video because I didn’t feel like preparing a brush.
After applying resin all over, lightly heat it with an embossing heater to remove excess resin and spread it evenly.
Spin it around for about a minute.
Then, cure it under the light as is.
After curing it thoroughly in place, apply resin to the top and bottom surfaces to coat them as well.
Instead of applying a thick layer of resin to make it rounded, it’s better to apply a thin, flat layer for a neater cylinder.
Apply a thin, even coat rather than a thick one to ensure a clean finish as a cylinder.
It’s complete! A beautiful cylinder that highlights Mount Fuji perfectly.
It looks great from every angle. I made it smaller this time for use as an accessory.
You could make it slightly larger for a keychain, which would also be cute!
If you enjoyed this video, I’d appreciate it if you could like the video and subscribe to my channel.
Thank you so much for watching until the end!
