Heat exchanger classification is where many design courses lose people: E-type, U-tube, kettle and floating tube sheet get listed as names without showing why each one exists. Chapter 3 of this heat exchanger design course takes them one at a time across six lessons and 3 hours 48 minutes. It starts with how exchangers are classified and the principles they operate on, then reads the schematics for each configuration. No prior knowledge is assumed, so it suits chemical and process engineering students as well as working engineers refreshing the basics. 🎁 Get a free lifetime account for premium courses 👉 https://graphicmade.com ⏱️ Chapters: 0:00:00 Understanding Heat Exchanger Classification 0:17:09 Description of E-Type Shells 1:10:11 Principles of Heat Exchangers 2:07:52 U-Tube Heat Exchanger Schematics 2:49:46 Details of Kettle-Type Heat Exchangers 3:15:50 Floating Tube Sheet Heat Exchanger Design For educational purposes only. This is not professional engineering advice; real equipment must be designed and checked against the applicable codes by qualified engineers. 🔔 Subscribe for more full-length courses: https://www.youtube.com/@graphicmade/ 💬 Which exchanger type do you work with most? Tell us in the comments. ━━━━━━━━━━━━━━━━━━ 📧 Contact: [email protected] 🔥 Learn Design. Create with Confidence. #GraphicMade #ChemicalEngineering #ProcessEngineering #MechanicalEngineering #HeatExchanger
Layout Design & Piping for Compressors, Pipe Rack, Columns, Heat Exchangers, Pumps.
Want to master PDMS (Plant Design Management System) for piping design and equipment modeling? 🛢️⚙️ This course gives you a complete, step-by-step training on how to design and model piping systems used in real industrial projects. Learn how to work professionally with AVEVA PDMS to create accurate plant layouts, piping networks, and equipment models used in Oil & Gas, petrochemical, and mechanical engineering industries. 🎬 TIMESTAMPS 0:00:00 PDMS Software Basic Information about Equipment 0:25:39 PDMS Piping Basics 0:37:11 PDMS Equipment Modelling Part 2 0:47:19 PDMS Equipment Modelling Part 3 0:53:27 PDMS Equipment Modelling Part 4 0:58:45 PDMS Equipment Modelling Part 5 1:10:44 PDMS Equipment Modelling Part 6 1:39:19 PDMS Piping Modelling Part 1 1:49:52 PDMS Volume Blocks 2:05:02 PDMS Piping Modelling Part 2 2:25:30 End of Course ✅ What You’ll Learn: Introduction to PDMS software and interface Piping design fundamentals and workflows Equipment modeling and placement Pipe routing and layout design Understanding plant structure and hierarchy Industry practices for Oil & Gas projects 🏗️ Perfect For: ✔ Mechanical & process engineering students ✔ Oil & Gas professionals ✔ Piping designers and engineers ✔ Beginners entering plant design 🔥 Build real-world skills used in industrial plants and engineering projects. 🚀 Why This Course? Beginner to advanced training Real project-based learning Industry-relevant software skills Step-by-step practical workflow 👉 Start your journey to becoming a professional piping designer today!
Welcome to this course. This course is designed to provide you entry-level knowledge of Piping Designing. You can find even more syllabus, is covered in this course than the standard PG Diploma in Piping Design Engineering. And if compare the cost, it cost you nothing as compared to a standard course. This Course is a perfect combination of theoretical study as well as practical work. You will Learn the use of your knowledge in practical work by some examples of exercises. Module 7 is coming soon. 🎬 TIMESTAMPS SECTION 0: COURSE INTRODUCTION 0:00:00 - Introduction 0:01:37 - Course Syllabus 0:07:02 - 0.0 Module Introduction SECTION 1: PIPING FUNDAMENTALS & COMPONENTS 0:08:09 - 1.1 Piping System 0:10:13 - 1.2 Plants Type-1 0:15:35 - 1.2 Plants Type-2 0:20:04 - 1.2 Plants Type-3 0:22:14 - 1.2 Plants Type-4 0:25:44 - 1.2 Plants Type-5 0:29:25 - 1.3 Plant Designing Type 0:31:36 - 1.4 Phases of Plant Designing 0:36:51 - 1.5 Types of Design Companies 0:39:40 - 1.6 Knowledge Requirement 0:46:10 - 1.7 Piping & Other Departments 0:51:26 - 1.8 Codes and Standards 0:57:05 - 1.9 Piping Components 0:58:08 - 1.10 Pipe 1:00:09 - 1.11 Pipe Designation 1:07:02 - 1.12 Pipe Manufacturing 1:14:08 - 1.13 Pipe Fittings-1 1:16:37 - 1.13 Pipe Fittings-2 1:19:08 - 1.13 Pipe Fittings-3 1:22:44 - 1.14 Pipe Flanges-1 1:25:57 - 1.14 Pipe Flanges-2 1:29:26 - 1.13 Pipe Fittings-4 1:33:56 - 1.14 Pipe Flanges-3 1:36:28 - 1.15 Flange Gaskets 1:39:59 - 1.16 Valves 1:41:25 - 1.17 Valves Types-1 1:50:34 - 1.17 Valves Types-2 SECTION 2: EQUIPMENT TYPES 1:57:28 - Module Intro 1:58:18 - 0.0 Equipments 1:59:21 - 1.1 Static Equipment 2:00:13 - 1.2 Tanks 2:06:52 - 1.3 Heat Exchangers 2:11:38 - 1.4 Heater & Boilers-1 2:14:26 - 1.4 Heater & Boilers-2 2:19:22 - 1.5 Columns 2:21:51 - 1.6 Reactors 2:23:40 - 1.7 Separators 2:27:28 - 1.8 Strainers 2:28:47 - 1.9 Air Vents 2:31:26 - 1.10 PIG Launchers 2:34:35 - 2.1 Rotary Equipments 2:35:18 - 2.2 Pumps 2:40:04 - 2.3 Compressor 2:43:55 - 2.4 Agitator 2:47:24 - 2.5 Turbines 2:49:23 - 2.6 Turbo Expanders 2:50:40 - 2.7 Engines 2:54:28 - 2.8 Fans & Blowers SECTION 3: PROCESS DESIGN & DOCUMENTATION 2:58:38 - 0.0 Module Intro 2:59:60 - 1.1 Project Documentation 3:02:45 - 1.2 Chemical Process Selection 3:09:15 - 1.3 Anatomy of a Chemical Process 3:14:19 - 1.4 Material Balance 3:18:56 - 1.5 Energy Balance 3:24:37 - 2.1 Plot Planning 3:34:15 - 2.2 Equipment Layout 3:40:15 - 3.1 Symbols 3:51:46 - 3.2 PFD & UFD 3:54:52 - 3.3 P&ID Exercise-1 (Tank) 3:58:50 - 3.4 P&ID Exercise-2 (Heat Exchanger) 4:03:14 - 3.5 P&ID Exercise-3 (Separator) 4:07:05 - 3.6 P&ID Exercise-4 (Column) 4:14:58 - 3.7 P&ID Exercise-5 (Complex) 4:26:18 - 4.0 Section Intro (GA, ISO DWG, Linelist) 4:28:02 - 4.1 GA DWG Ex-1 (Part-1) 4:36:25 - 4.1 GA DWG Ex-1 (Part-2) 5:09:25 - 4.1 ISO DWG Ex-1 5:26:14 - 4.1 Line-List SECTION 4: FLUID MECHANICS & CALCULATIONS 5:29:23 - 0.0 Module Intro 5:30:26 - 1.1 Fluid & Its Properties 5:37:02 - 1.2 Types of Fluids 5:40:06 - 1.3 Fluid at Rest 5:42:43 - 1.4 Fluid in Motion 5:45:32 - 1.5 Continuity Equation 5:51:04 - 1.6 Bernoulli's Theorem-1 5:55:18 - 1.6 Bernoulli's Theorem-2 5:59:13 - 1.7 Pipe Size Calculation 6:07:49 - 1.8 Pipe Thickness Calculation 6:12:55 - 1.9 Pump Selection 6:18:39 - 1.10 Insulation Thickness Calculation 6:24:00 - 1.11 Mitre Bend Calculation 6:30:27 - 1.12 Dyke Wall Calculations SECTION 5: FABRICATION & SUPPORTS 6:35:50 - 0.0 Module Intro 6:37:34 - 1.1 Fabrication Activities 6:40:58 - 1.2 Types of Welding 6:45:46 - 1.3 Piping Lining 6:51:33 - 1.4 Piping Insulation 6:56:42 - 2.1 Supports Introduction 6:58:02 - 2.2 Types of supports 7:00:43 - 2.3 Hanger Supports 7:05:59 - 2.4 Clamp Supports 7:10:41 - 2.5 Strap Supports 7:14:46 - 2.6 Saddle Supports 7:18:59 - 2.7 Slide Supports SECTION 6: STRESS ANALYSIS & TESTING 7:21:18 - 0.0 Module Introduction 7:22:49 - 1.1 Types of Stresses 7:26:23 - 1.2 Static Loads 7:30:28 - 1.3 Dynamic Loads 7:35:56 - 2.1 Visual Inspection 7:38:18 - 2.2 Liquid Penetration Test 7:40:27 - 2.3 Magnetic Particle Test 7:44:41 - 2.4 Radiographic Testing 7:48:15 - 2.5 Ultra-Sonic Testing 7:49:48 - 2.6 Hydrostatic Pressure Testing 7:52:29 - 2.7 Pneumatic Pressure Testing 7:55:37 - End of Course
Introduction to Piping Fabrication ( Mechanical Engineering, Process Engineering, Petroleum, Oil & Gas Industry ) 🎬 PIPING ENGINEERING MASTERCLASS - FULL TIMESTAMPS SECTION 1: INTRODUCTION & BASICS 0:00:00 Introduction 0:02:41 Piping Basics 0:11:35 Codes & Specification SECTION 2: PIPING COMPONENTS 0:20:47 Flanges 0:38:35 Fittings 0:54:37 Valves 1:03:19 Gaskets & Fasteners SECTION 3: ISOMETRICS BASICS 1:13:00 Isometrics Basics 1:25:00 Isometrics Study - Type 1 (Part 1) 1:38:20 Isometrics Study - Type 1 (Part 2) 1:51:18 Isometrics Study - Types 2, 3 & 4 SECTION 4: ISOMETRICS & SHOP SPOOLS 2:06:21 Isometrics & Shop Spools - Type 1 2:12:34 Isometrics & Shop Spools - Type 2 2:18:45 Isometrics & Shop Spools - Type 3 2:25:57 Isometrics & Shop Spools - Type 4 SECTION 5: FABRICATION & DOCUMENTATION 2:36:21 Fabrication Schedule Review 2:41:33 Piping Inch Dia Sheet Review 2:52:40 Piping BOQ SECTION 6: CUTTING & FIT-UP 2:56:15 Cutting, WEP & Fitups 3:12:08 Fitup Video - Pipe, Elbow & Flange 3:19:17 Welding 3:30:41 Weld History Sheet & Hydrotest SECTION 7: ADDITIONAL VIDEOS 3:43:12 Fitup of Weldolet 3:49:48 Pipe Cutting 3:55:46 Painted Spools 3:58:12 End of Course
Master piping design, materials & stress analysis per ASME B31 for oil & gas industries - Trained 745+ engineers Learn more & access premium courses at 👉 allgoodtutorials.com
Master piping design, materials & stress analysis per ASME B31 for oil & gas industries - Trained 745+ engineers 🎬 COMPLETE PIPING ENGINEERING DESIGN COURSE - TIMESTAMPS SECTION 1: CODES, CRITERIA & PIPE SIZING 0:00:00 Codes and Design Criteria 0:30:16 Pipe Diameter & Pressure Loss SECTION 2: MATERIALS, SPECIFICATIONS & COMPONENTS 0:49:56 Material Selection 1:23:25 Piping Specification 1:53:51 Valves 2:15:10 Piping Insulation SECTION 3: PRESSURE DESIGN & LAYOUT 2:35:39 Internal Pressure 2:55:11 External Pressure 3:09:53 Buried Piping Design 3:28:13 Piping Layout 3:40:41 Equipment Interconnection 3:55:09 Stress and Flexibility Analysis 4:11:24 Support Design 4:22:10 End of Course Welcome to AllGoodTutorials 🎯 Your all-in-one learning platform for professional online courses across multiple fields. From Cybersecurity, Ethical Hacking, Programming, Linux, Design, Business, Marketing, and AI — to real-world projects and career-ready skills. Learn step by step with structured courses, practical tutorials, hands-on labs, and clear learning paths from beginner to professional. 📞 CONNECT WITH US ◾ WhatsApp: +212 6 37 64 87 13 ◾ Email: • General: [email protected] • Support: [email protected] 💎 SUPPORT ALLGOODTUTORIALS Help us create more high-quality free educational content 👇 ☕ Support us here: 👉 https://store.allgoodtutorials.com/pages/supporters 🎁 Unlock premium courses, learning paths & exclusive resources (Free trial available): 👉 https://store.allgoodtutorials.com/supporters/pricing 🌐 FOLLOW ALLGOODTUTORIALS 🔵 Facebook Group: https://www.facebook.com/groups/allgoodtutorials/ 🔵 Facebook Page: https://www.facebook.com/AllGoodTutorialsOfficial/ ⚫ Instagram: https://www.instagram.com/allgoodtutorials/ ⚫ X (Twitter): https://x.com/allgoodtuts 📌 Pinterest: https://www.pinterest.com/allgoodtutorials/ 👾 Reddit: https://www.reddit.com/user/allgoodtuts/ 🔗 LinkedIn: https://www.linkedin.com/in/allgoodtuts/ ✍️ Medium: https://medium.com/@allgoodtutorials 🚀 ABOUT ALLGOODTUTORIALS AllGoodTutorials is a comprehensive online learning platform offering professional courses in: ✔ Cybersecurity & Ethical Hacking ✔ Programming, Linux & IT Skills ✔ Design, Business, Marketing & Digital Skills ✔ Real-world projects & practical labs ✔ Career-focused learning paths Our mission is to help learners worldwide move from beginner to professional with clear, practical, and structured training. 🔔 STAY UPDATED ✅ Subscribe to the channel ✅ Activate the bell 🔔 ✅ Like the video 👍 So you never miss new tutorials, full courses, and premium content. 👉 Subscribe here: https://www.youtube.com/@allgoodtutorialsClips1/videos ☕ EXTRA SUPPORT (Optional) Support us on Buy Me a Coffee: 👉 https://buymeacoffee.com/allgoodtutorials
Master piping design, materials & stress analysis per ASME B31 for oil & gas industries - Trained 745+ engineers This video provides a comprehensive overview of piping design and analysis for the oil and gas industries, strictly adhering to the standards set by ASME B31. It covers the fundamental principles, codes, and best practices for designing and analyzing piping systems to ensure safety, efficiency, and compliance with regulatory requirements. The content is tailored for professionals and students seeking to master the skills necessary for successful piping design and analysis in the oil and gas sector, including understanding material selection, stress analysis, and the implications of various design choices. By watching this video, viewers will gain a deeper understanding of how to apply ASME B31 standards to real-world piping design and analysis challenges, enhancing their ability to work effectively in the oil and gas industries.
To learn Piping Design Engineering Fundamentals is important. This video has full free Piping Design Engineering Course. This video is helpful for piping engineering world, piping engineer work, piping engineering course, and piping engineering jobs, designers, inspectors, maintenance, operation, and project management.









