## Problem 2017 Lexus RX350 with the new classic Toyota V6 engine 2GR-FKS: + 83,000 miles + with the factory spark plugs Toyota recommends 60,000 miles interval for spark plug replacement. Have to replace them but will start with the plugs in the front, which are easier to remove. Will also see what the spark plugs look like after 6 years and more than 80 thousand miles. ## Procedure 1. Park your vehicle on a level surface and turn off the engine. 2. Open the hood and remove engine cover. 3. Disconnect the electrical connector from each ignition coil by pressing down on the release tab and pulling it away from the coil. 4. Remove the ignition coil by using a ratchet * 10mm socket to unscrew the bolts that hold it in place. * Pull the ignition oil from the tube. 5. Use a spark plug socket to remove the old spark plug from the cylinder head. Turn the socket counterclockwise to loosen and remove it. 6. Check the condition of the old spark plug. * Wet/oil on the threads of one plug; should monitor possible oil leak of tube o-ring. * Clean and no carbon deposit, gap still within spec. 7. Compare to the new plugs; they should have the same size and specs. 8. No anti-seize compound on the threads of the new spark plug. The new plugs are pre-gapped so no need to gap them. 9. Use the spark plug socket to thread the new spark plug into the cylinder head. Turn the socket clockwise until the spark plug is snug and seated properly. 10. Use a torque wrench to tighten the spark plug to the specified torque for your vehicle. For the 2GR-FKS engine, the torque specification for spark plugs is 13 lb-ft (18 Nm). 11. Repeat steps for each spark plug that needs to be replaced. We will replace the rear spark plugs in another video. 12. Reinstall the ignition coils by using the ratchet and socket to tighten the bolts that hold them in place. 13. Reconnect the electrical connectors to each ignition coil by pushing them into place until they click. 14. Start the engine to test the new spark plugs. 15. Reinstall engine cover, which makes the engine sound quieter. ## Notes Again, Toyota recommends 60,000 miles interval for spark plug replacement on this engine another latest models. Spark plugs are cheap so do not delay in their replacement (like me) as worn spark plugs can stress out other more expensive components of the engine such as ignition coils. Hope this is helpful. God bless!
It is a sealed transmission on a Toyota or Lexus. No dipstick on the transmission. Toyota says it is life-time transmission fluid?! Is it really life time? Do you replace the transmission fluid? Do you also replace the filter (strainer) inside the transmission oil pan? These are important questions for the life of your car.
# Easy Removal of Paint Transfer / Scuffs on Your Car ## Reason * I have multiple paint scuffs on the beautiful Lexus RX350. Some of these look terrible (see what happened at the end). * Fortunately, they are very easy to remove and you only need very basic supplies. ## Paint Transfer or Scratch? How do you know it is paint transfer and not a (deep) scratch? 1. Paint transfer is a different color of paint on top of your car's paint/clear coat. 2. You can feel the "bump" when rubbing your finger on it. 3. Or, if you rub it with a wet finger, it may come off a bit. ## Tools or Supplies * [ ] Microfiber towels * [ ] WD40 * [ ] Mr. Clean MagicEraser (Durafoam) * [ ] Polishing Compound * [ ] Optional: Rubbing Compound ## Steps 1. [ ] Park your car in garage, under the shade, or do this on a cloudy day (NO Direct Sunlight) 2. [ ] Clean the surface with water (and soapy water if necessary) * [ ] Make sure there is NO Dirt * [ ] Clean, rinse, and wipe off with microfiber towels 3. [ ] Spray WD40 on the transferred paint * [ ] Let it soak for a minute if possible, and repeat the spray * [ ] WD40 will soften the paint and lubricate the removal/rubbing process 4. [ ] Lightly rub the paint with Mr. Clean MagicEraser foam * [ ] Follow the direction of the scuff * [ ] Check your foam and make sure you only remove the transferred paint, NOT the paint of your car 5. [ ] Wipe off, spray WD40 again, and repeat the process until the paint transfer is removed. 6. [ ] Clean the surface, and polish it with some polishing compound on microfiber towel * [ ] You may start with the rubbing compound first, before applying the polishing compound * [ ] Use a circular motion to apply the compound, with light/moderate hand pressure ## What Happened and Caused the Paint Transfer? 1. Other cars rubbed/"scratched" your car in the parking lot, and left their paint on it. 2. What happened to the big scuffs on my Lexus: Wife was at traffic lights when someone cut her off and rubbed the side of the car. That person did not have the courage to stop, and he ran away. My wife felt very upset with the terrible marks (thinking it were damages to the Lexus body paint) and couldn't believe it after I removed the scuffs 15 minutes later. -- Be safe. Enjoy the work! God bless!
# Lexus Carplay Upgrade 4 Month Review and Tips Link to installation video: https://youtu.be/I8eCbVxB6e0 * Have used it for 4 months and thousands of miles, * on local, high-way, and out of state trips. * Family members who like and don't like technology. * Overall, very positive experiences. ## Tips and Settings Correction first: * Don't stick the Antenna to metal as there can be interference. - The manual says that but I ignored it in my installation (not correct). - Practically, I haven't noticed a problem and it may impact some of your installation/connections. Tips: 1. AUX on the dash and wheel control; no need to long press Menu to switch back to the original Lexus infortainment. 2. Remote lever/touchpad setting, e.g. remote lever 3. Phone audio echo/loop (for the other party): change Mic Pre-config for IS or LX. ## Connection 1. Bluetooth and Wifi on, occassionally reconnect. 2. USB: charger and wired carplay, always works; but may have to give permission. * USB cable does not affect opening or closing of the glove box. 3. Multiple devices, automatically connect to one; USB wired connection is picked up first. ## Control 1. On remote lever or joystick, make sure the setting is correct. 2. Left and right (most used) for horizontal and vertical navigation. 3. Up and down (rarely used) to FAST vertical scroll. 4. This is one feature I don't fully appreciate, but it works. ## Key Features ### SIRI 1. SIRI is the lifesaver, especially on the trip. 2. You can access almost everything available to Carplay via Siri. 3. Long press Remote Lever, Touch Pad or one of the Enter keys. 4. Lexus Voice Assistant on wheel remains the same, and cannnot be used to activate Siri. ### Phone Calls 1. Again, use Siri to make phone calls or read messages, etc. 2. Good news: On-wheel buttons to receive and reject (hang up) calls WORK! * Use them to receive/reject incoming calls * Or to activate the phone/contact page on Carplay. 3. You can still use Remote or Phone to look up and make calls. ### Maps and Modes 1. Google Maps and Apple Maps both work nicely. 2. Apple Maps works seamlessly with Siri * There appears to be a way to activate Google Maps from Siri but I haven't figured that out. 3. I use TuneIn radio while on Maps: * Full Maps or split with Maps and Now Playing * Automatically mute/reduce the volume on radio, when there is voice guidance or incoming call. * Sound quality is great! Though I normally only listen to talk show radio and can be biased. 4. Alternatively, with on-wheel control, you can easily (manually) switch to other media sources, e.g. AM/FM. ## Long Term and Long Trips * Overheat? No problem with mine. But some people place the unit in the glove box. * It is in the radio unit on the AC passage. * On the road, Siri is handy, receive calls on the wheel, and other carplay control (brief) on the remote (right-hand side). ## Android Auto 1. Downloaded Autolink (third-party app) but that was not working/used. 2. Use the built-in Android Auto (on Android One device). 3. Tested USB and WiredAuto, worked fine. 4. Likewise to activate Hey Google/Assistant, by long press Remote Lever, Touch Pad or Enter. 5. Didn't use Android Auto extensively; tested it with an outdated Android One phone and Maps with offline (downloaded) data. ## Different Configurations * Wiring can be different depending on your model and configuration. Make sure to check and get support from the seller. * For example, for some models, there is an additional Audio Ground Wire to be connected separately. * Some people reported having to update firmware on the carplay unit. * It supports 360 cameras, either original Lexus cameras or aftermarket ones. But I haven't tested it as this is not part of my model/configuration. ## Things to Know 1. Installation can be tricky, and wiring varies on configurations. 2. Remote lever is not the best control but works just fine. 3. On-wheel buttons are not fully utilized, only the two phone-related buttons. Would be good to use other buttons such as arrow keys to navigate the carplay system. 4. If you have to use other audio sources such as AM/FM or other bluetooth audio input, you won't be able to have AUX and audio from carplay at the same time. Unlike the original Lexus infotainment, which can give your voice guidance regardless of your audio mode. Overall, my experiences have been overwhelmingly positive so far. -- Hope this is helpful and informative. If there are other questions or issues not covered in this video, please feel free to ask in the comments. Stay tuned as I will continue to share tips from my journey of car care and repairs. Appreciate your attention to Professor's Garage. God bless!
# Tire Rotation for an AWD (X Pattern) X Rotation for an All-Wheel Drive ## Tools 1. Breaker bar or impact wrench 2. Torque wrench 3. Floor jack, x1 4. Jack stands, x4 ## Preparation Note if you use a breaker bar, you may have to loosen (NOT remove) lug nuts before raising the vehicle. 1. Raise the vehicle, both the front and the rear. 2. Support the vehicle with jack stands (4). ## Rotation Steps 1. Remove the right front, and move it to the left rear. 2. Remove the left rear, and install the tire from the right front & secure lug nuts. 3. Remove the left front, and move it to the right rear. 4. Remove the right rear, and install the tire from the left front & secure lug nuts. 5. Lower the rear of the vehicle, and tighten the rear lug nuts to torque spec. 6. Install tire from right rear to left front, and secure with lug nuts. 7. Install tire from left rear to right front, and secure with lug nuts. 8. Lower the front of the vehicle and torque front lug nuts to spec. 9. Double-check torques. 10. Done. ## Notes * I rotate the tires every 5000 miles or so. * This procedure is for non-directional tires. This cannot be done on directional tires such as some winter tires. -- Be safe, stay dirty. Enjoy the work! God bless!
Replacement of Rear Brake Pads on a 2017 Lexus RX350 AWD Base model ## Supplies 1. Rear brake pads: 2x2 for both sides 2. Brake hardware & lubricant/grease 3. Brake cleaner 4. Thread locker (blue) ## Tools 1. Breaker bar or ratchet wrench x1 2. 14mm and 21mm sockets, and preferably a 17 mm box wrench 3. Bungee cord x1 4. Torque wrench: 25 and 76 ft pounds 5. Syringe or turkey baster 6. 12 volt DC plus small test leads ## 1. Safety and Preparation 1. Loosen (but not remove) lug nuts on the rear wheels, with a 21 mm socket. 2. Jack up the car (rear) and support it with jack stands. 3. Make sure the support is stable. Safety check! 4. Pop the hood, and take out some brake fluid. 5. Remove the lug nuts, and remove the wheels. 6. Put wheels under the car for additional protection. ## 2. Brake Caliper Removal 1. Remove two mounting bolts (14 mm), with: 1. with a 17 mm box wrench to hold the pin in place 2. and ratchet with 14mm socket to loosen the bolt 2. Remove the connector from the electric parking brake (EPB) motor. 3. You may slide the pins (top and bottom) out to remove them. 4. Remove and secure the caliper with a bungee cord. ## 2. Disengage Electric Parking Brake (in Service Mode) With a 12 volt DC power: 1. Put the brake pressing tool on the caliper, lightly touching the piston. 2. Connect battery negative (with a small test lead/clamp) to one pin on the EPB motor. 3. Connect/touch the positive lead to the other pin on the EPB motor, and you should hear the motor running sound. 4. Observe if the piston is pushing out (to tighten the pressing tool) or withdrawing (to loosen the pressing tool). 5. Once you know the correct connection to retract, repeat the following steps: 1. Activate the motor to retract; 2. Compress the piston; 6. Repeat the above until the piston is flush with the caliper surface. 7. The caliper/piston is ready to be reinstalled with new pads. For other methods to put EPB in the service mode, you can watch this video: https://www.youtube.com/watch?v=XgaRKr3BRvI ## 4. Brake Pad Replacement 1. Clean and grease /lubricate the pins. 2. Slide them back into the caliper bracket, boots on. 3. Remove the old pads, and pry off the existing hardware. 4. Apply a bit of grease on new hardware (on the pad touching contact), and install them. 5. Install the wear indicator hardware on the pad. 6. Slide the pad in an angel, turn, and push it in. 7. Apply some grease on the back/shim of the pad. 8. Replace the inside pad in the like manner. The same procedure but it is difficult to see and takes some patience. :) 9. Put the brake caliper back on the pads. 10. Apply blue thread locker on the mounting bolts. 11. Tighten the bolts (14 mm x2) to 25 ft-lb. ## 5. Finishing 1. Repeat the steps for the other side 2. Reinstall the wheels with lug nuts 3. Lower down the vehicle 4. Torque lug nuts to 76 ft pounds. 5. Check brake fluid level. 6. Start the car and pump the brake pedal several times. ## 5. Breaking in Follow instructions on the pads for breaking-in procedures, if necessary. -- Hope this video helps. Be safe, stay dirty. Enjoy the work! God bless!
# Toyota Lexus Rear Brakes with EPB: 3 Methods to Enter the Service Mode Rear brake service on a 2017 Lexus RX350 AWD Base model ## Tools These are options: 1. Bidirectional scan tool, OR 2. If you have a recent Toyota/Lexus models that supports a simple procedure, OR 3. 12 V DC battery ## Safety and Preparation Follow all safety precautions to any job on a vehicle. ## Method 1: Use a Bidirectional Scan Tool On a XTool, for example: 1. Connect the OBD scan tool. 2. Start the car. 3. On XTool, select Special function / EPB / ASIA / Lexus / Automatic selection. 4. Select Enter Maintenance Mode, and confirm. 5. You should hear a whining sound to disengage the parking brake. 6. Parking light will be flashing slowly. 7. Now the vehicle is in the service mode. To exit service mode after service is done: 1. Select Exit Maintenance Mode, and confirm. 2. You should hear a whining sound to reengage the parking brake. 3. Parking light will turn solid. 4. Now the vehicle is back to normal operations. ## Method 2: The Toyota / Lexus Procedures This may or may not work on your vehicle so research your year/model to find out. It doesn't work on my 2017 Lexus RX350, but on later models after 2019. Disengage Electric Parking Brake (in Service Mode): 1. Without pressing the brake pedal, start the car once. 2. While depressing the brake pedal, within 8 seconds: 1. Pull (up) the (P) lever 3 times; 2. Push (down) the (P) lever 3 times; 3. While foot OFF brake, push and hold (P) unless the (P) indicator on dash is flashing SLOWLY. * You may be able to hear the rear brake's electric rotor is running to retract the piston. 4. Release the (P) lever, and it is now in the Service mode. 5. Press Start/Stop to turn off ignition. Re-Engage Electric Parking Brake (cancel Service Mode): 1. Without pressing the brake pedal, start the car once. 2. While foot off brake, pull and hold (P) lever until the (P) light is out. * You may be able to hear the rear brake's eletric rotor sound again. 3. Release the (P) lever, and it is now back to normal (with eletric parking brake) 4. Press Start/Stop to turn off ignition. ## Method 3: Use a 12V DC Power After the removal of the connector to the brake piston motor on the caliper: 1. Put a brake pressing tool on the brake piston, loosely engaged. 2. Connect one wire (e.g. black/negative) of the 12V DC to one pin on the motor. 3. Contact the other wire (e.g. red/positive) of the 12VDC with the other pin on the motor. 4. The motor will run and whine when the power is provided. 5. Make sure the motor is retracting the piston: 1. If it runs and compresses the pressing tool (making it tighter), reverse the two wire/connectors. 2. Only run the motor very briefly, and try to compress the piston with the pressing tool. 3. You can easily press piston with the tool if the motor is retracting in the right direction. 4. Do not force. 6. Once it is full retracted, you compress the piston to flush. ## Brake Job Afterwards If one of the methods works, you can then proceed with the rear brake job. -- Be safe, stay dirty. Enjoy the work! God bless!
# Lexus Oil Change 2017 Lexus RX350 Base AWD Engine: Toyota 3.5L V6 2GR-FKS ## Supply 1. Oil: 0W20 x5.8 qt 2. Oil Filter: 04152-YZZA1 1 $4.21 Oil filter cap torque 18 ft-lb 3. Drain gasket: 90430-12031 1 $0.88 Drain plug torque 30 ft-lb 4. Disposable gloves ## Tools 1. Ratchet socket wrench or breaker bar x1 2. 14 mm socket (or box wrench) 3. Oil filter wrench for Toyota/Lexus 4. Torque wrench (18 and 30 ft-lb) ## Safety and Preparation 1. Engage parking brake 2. Chocks 3. Pop the hood 4. Raise the car: using floor jack + jack stands or ramps 5. Safety check!!! ## Oil Change 1. Tip: Warm up the engine, 5 minutes 2. Open the oil cap, read the oil grade (0w20), or owner's manual 3. Remove the drain plug (14mm socket), and drain oil 4. Remove oil filter, with a filter wrench 5. Replace oil filter, and make sure: 1. clean 2. lubricate the rubber o-ring with oil 3. check cap on the filter, finger tight 4. torque oil filter to 18 ft-lb 6. Replace drain plug with new crush washer, clean, and torque to 30 ft pounds 1. Make sure to remove any remnant of gasket on the drain pan or bolt 7. With a funnel, add 5+ gallons, check it, and add more if necessary 1. check owner's manual, OR 2. measure the amount you take out 8. Start the engine, check leaks, shut off and measure with dipstick 9. For accurate oil level measurement, make sure your car is level * you can lower the car at this point 11. Make sure no leak near oil filter and drain plug ## Oil Reset 1. Menu / Settings 2. Vehicle settings 3. Services/Maintenance / Reset Oil Change 4. Edit and set 5000 miles for the next service ## Final Comments 1. Oil change interval: 5000 miles or 6 months, whichever comes first 2. Oil type: Synthetic 0w20 3. Oil brand: doesn't matter as long as it is 0w20 (check your owner's manual) 4. Recycle the used oil Be safe, stay dirty. Enjoy the work! God bless!
# 2017 Lexus RX350 Infotainment/Navigation Upgrade to CarPlay ## Supply 1. CarPlay & Android Auto module + interface cables In the video, I install a RoadTop CarPlay unit for Lexus: https://www.ebay.com/itm/384400476740 * I have NO affiliation with them and hope to post a review video after some use. * For now, I've used CarPlay features but will test Android Auto too. ## Tools 1. Panel removal tools (plastic) 2. Ratchet wrench 3. 10mm socket 4. Some towels ## A. Radio Unit Removal 1. Open storage lid and remove central console panel/trims. 2. Remove (silver) trims around the radio. 3. Remove black trim where Start/Stop button is attached. 4. Disconnect Start/Stop connector. 5. Remove two 10mm bolts holding the radio: + one on the driver side + the other on the passenger side 6. Push down shift boot and remove shift knob. 7. Cover the shift stick with towels (to protect the radio unit later). 8. Remove the radio unit, and disconnect the connector at the top. ## B. Screen Removal 1. Remove front and back trims around the screen. 2. Remove back cover of the screen. 3. Remove three 10mm bolts/nuts on the screen bracket. 4. Lay towels in the front. 5. Remove the screen and place it on the towels. ## C. Connect CarPlay Unit Cables 1. Connect LVDS cables. 2. Connect CAN cables. 3. Connect USB / Video cables. 4. Connect RF Antenna cable. 5. Change Toggle Switch according to instructions. ## D. Connect to Radio Unit Host For each connector, chain them together this way: 1. Remove the original cable; 2. Plug it to the female cable to CarPlay; 3. Plug the carplay male to the host socket, where the original cable is removed. Do this for the following cables/connectors: 1. Power or CAN cables. 2. Audio out cables. ## E. Connect to Screen 1. Route LVDS cable from the back of the radio to screen. 2. Chain the LVDS connectors with the original cable/connector. ## F. Test CarPlay 1. Reconnect Start/Stop and start the car. 2. Switch Audio Source to AUX. 3. Turn your phone's wifi, bluetooth, and connect to CarPlay. 4. Test the features. ## G. Reassembly 1. Optional: Route the USB cable to glove box. The unit has wireless carplay so USB is not required. 2. Place the CarPlay unit in the back behind Radio. Arrange the cables and tuck them in the back. 3. You can stick the antenna to the side of the radio box. 4. Put the radio unit back, attach to the clips, 10mm bolts, and reattach the trims. 5. Reinstall the screen with 3x10mm bolt/nuts, back cover, front and back trims. DONE. Hope this video is informative. Be safe, stay dirty. Enjoy the work! God bless!









