Replace power steering fluid regularly, every 30,000 miles or 2-3 years. It is the hydraulic fluid that help you turn the wheel and a lubricant for the moving parts of your steering system, especially for the longevity of your steering pump and steering rack. #powersteering #carmaintenancetips
# Check engine light P0302. Spark plug or ignition coil pack? Diagnosis and fix. Or related code P0301, P0303, P0304, P0305, P0306, P0307, P0308. Vehicle: 2010 Honda Odyssey Ex-L Engine: Honda V6 J35A7 ## Problem Code: P0302 Cylinder 2 Misfire ## Analysis Most common causes: 1. Spark plug; OR 2. Ignition coil pack; ## Test 1. Take out the ignition coil pack from a GOOD cylinder, e.g. cylinder 4. 2. Take out the ignition coil pack from the BAD cylinder, i.e. cylinder 2. 3. Swap the two coil pack, that is: * Install coil pack \#2 to cylinder 4 * Install coil pack \#4 to cylinder 2 4. Clear code, start the engine, and scan engine. ## Result and Fix ### Scenario 1 IF the code changed to: "P0304 cylinder 4 misfires" meaning the GOOD cylinder is now bad with the new coil pack, replace the coil pack. ### Scenario 2 IF the code comes back with an unchanged misfire code: "P0302 cylinder 2 misfires" Then the coil is not the culprit, and it is most likely the spark plug in the BAD cylinder. Replace the spark plug: 1. With a spark plug socket, take out the old plug from the BAD cylinder, i.e. number 2. 2. Thread the new plug on with a small ratchet and fingers. 3. Torque to 13 ft-lb, or hand-tight. * No grease (anti-seize) * Do NOT over-tighten 4. Clear the code and have a test drive. 5. All done if code doesn't come back. ## Notes On spark plug replacement: 1. If it has been a while since last spark plug replacement, you may consider replace them ALL. 2. If one starts to go out, it's likely the others will do too. 3. Don't stretch it as it can lead to more costly repairs later. 4. Examples on spark plug replacement intervals: * Honda engines: no more than 100k miles * Toyota engines (old): no more than 120k miles * Toyota engines (latest): no more than 60k miles On other causes of misfire: 1. Bad fuel 2. Bad fuel injection 3. Engine lubrication, oil getting into combustion 4. Others Fix the problem ASAP as it can lead to more catastrophic problems on the engine and/or catalytic convertor, which are very costly. -- I hope this video is helpful and informative. Consider give us a like and subscribe! God bless!
# Why your steering wheel shakes (pulsation) when braking and fix it in 6.57 minutes Vehicle in the video: 2010 Honda Odyssey EX-L ## Concerns Steering wheel pulsation when you brake/slow down... especially on the highway. Possible causes: 1. Likely uneven wear of brake pads and/or warped brake rotors. 2. Front brakes and/or rear brakes. In the case of my 2010 Honda Odyssey, it was the rear brakes. ## Supply 1. Rear brake rotor x2 2. Rear brake pad x2 3. Brake lubricant / grease 4. Anti-seize paste 5. Brake cleaner 6. Thread locker (blue) 7. Optional: brake fluid 8. Optional: Penetrating oil, e.g. PB blaster or WD40 ## Tools 1. Breaker bar or ratchet wrench x1 2. 12 mm, 17mm, 22mm sockets 3. Bungee cord x1 4. Torque wrench: 65 and 16 ft pounds 5. Caliper piston pressing tool (or a clamp) 6. Manual impact screw driver (recommended) 7. Wire brush 8. Optional: M8 x 1.25 bolt x2 ## 1. Safety and Preparation 1. Engage parking brake first 2. Chocks 3. Pop the hood, take out some brake fluid 4. Loose the lug nuts (22 mm socket) 5. Raise the car, take off the nuts, and tires 6. Tires under car for additional protection 7. Safety check!!! ## 2. Rotor and Pad Removal 1. Remove brake calliper: bolts 12 mm x2 2. Hang calliper with bungee cord 3. Remove brake bracket: 17 mm bolts, it helps to use penetratig oil 4. With safety check and parking brake RELEASED, remove rotor: I. Impact screw driver to remove factory screws II. Run 8x1.25 bolts to separate the rotor ## 3. Rotor and Pad Installation 1. Wire brush / prep /clean the wheel bearing hub (remove rust for a clean surface) 2. Clean the rotor with brake cleaner 3. Align the set holes and put the factory screws back on 4. Wire brush / prep /clean the bracket 5. Install brake hardware (shims) 6. Regrease /lubricate the pins 7. Thread lock the bracket bolts (17mm) x2 8. Reinstall the bracket, and torque to 65 ft pounds 9. Grease the new pads: back, top, bottom 10. Install the new pads (slide in with an angle and rotate) 11. Note the brake with wear indicator is inside 12. Press the caliper piston: I. Make sure they are fully seated in the rubber boots II. Check brake fluid in the master cylinder (no overflow) 13. Clean and grease piston contact 14. Reinstall the caliper, with 12mm bolts thread-locked 15. Torque to 16 ft pounds ## 4. Finishing 1. Repeat the steps for the other side 2. Reinstall the wheels with lug nuts torqued to 94 ft pounds 3. Lower down the vehicle 4. Add brake fluid back to maximum 5. Pump brake pedals until it is firm ## 5. Breaking in Follow instructions on the rotors/pads for breaking in procedures. Hope this video is informative. Be safe, stay dirty. Enjoy the work! God bless!
# Honda Transmission Fluid Change Vehicle in video: 2010 Honda Odyssey EX-L ## Tools and Supply 1. 3/8'' rachet 2. OR, a 3/8'' breaker bar 2. 17 mm socket x1 4. Torque wrench (set at 29 and 36 ft pounds) 5. Honda ATF (DW-1), 3.3 quarts 6. Gaskets, for fill and drain plugs * Honda fill cap washer part #90441-PK4-000 (24mm) * Honda drain plug washer part #94109-20000 (I.D. 18mm) ## Safety and Preparation 1. Raise car 2. Pop hood 3. Chocks 4. Safety check!!! ## Fluid Change 1. Take off the fill cap with 17mm socket, long extension and perhaps a swivel 2. Put catch pan under transmission. 2. Take off the transmission drain plug with 3/8 ratchet or breaker bar. 3. Let it drain... 4. Clean the drain plug, shavings on the magnet. 5. Replace the drain plug with a new gasket, put it back after drained, and torque it to 36 ft-lb 6. With a long funnel, fill about 3.3 quarts of Honda DW-1 Transmission fluid. 7. Replace fill cap with a new washer, but don't tighten it yet. 8. Check fluid level on ground level, after vehicle reaches operating temperature, and engine OFF 9. Torque fill cap to 29 ft-lb ## Final Comments 1. Fluid change intervals * First change at 60,000 miles * Change every 30,000 miles afterwards 2. What fluid: best to use Honda fluid for that year & model 3. No flush; if you change it every 30k miles, that's good for the transmission. 4. Fluid color means little; it becomes dark once you put it in. -- Be safe, stay dirty. Enjoy the work! God bless!
# To Burn, or Not to Burn (Oil vs. Fuel), Honda Engine VCM Honda V6 Engine with VCM (Variable Cylinder Management) shown in the 2010 Odyssey Ex-L ## Problem * Honda V6 (J35A7) burns oil, at least 1 quart every 1500 miles ## Reason * VCM (Variable Cylinder Management) is the likely culprit * VCM shuts off some of the cylinders to consume LESS FUEL, which is good in this time of high gas prices * HOWEVER, it creates imbalances and vacuums in the engine with likely problems such as: 1. Engine and mount wear (and noise/failure over time) 2. OIL BURNING, bad for the engine, cat converter (costly), and the environment 3. It can ruin the engine if the oil level goes too low * You can disable VCM by adding a muzzler (resistor) to the coolant temperature sensor: * VCM is only turned on after the engine is WARMED up (at a certain coolant temperature) * Added resistor increases sensor OHM and signals a temperature below the desired condition for VCM, which will not get turned on ## Supplies 1. Honda VCM Muzzler / DIPressor 2. OR, if you can make a resistor of varying 82-100 ohm, that may work as well. Here is the one I purchased on eBay: https://www.ebay.com/itm/265031739235 ## Tools Optional: 1. An OBD II Scanner to clear code, in case it appears ## Steps 1. Engine OFF 2. Pop the hood 3. Remove the engine cover 4. Remove the coolant temperature sensor 5. Chain the muzzler with sensor: sensor harness to muzzler to sensor connector on the engine block 6. Start with the lower DIP or ohm setting, e.g. at 82 ohms. 7. Test the car to see if ECO mode appears in any driving condition. 8. Adjust/increase ohm if necessary and test drive again, until VCM no longer returns. Here are my DIP settings in Pennsylvania USA: 1. 82 ohms in the Winter 2. 92 ohms in the Summer ## Results 1. ECO never comes back with the above settings. 2. I no longer need to add oil between oil changes. -- Be safe, stay dirty. Enjoy the work! God bless!
# Windshield Long Crack Repair ## Purpose With a 6-inch long crack on the windshield, hope the repair will: 1. make it less visible; 2. stop the growth of the crack; ## Supply * RainX Windshield Repair Kit (resin bottle) https://www.rainx.com/product/rain-x-windshield-repair-kit/ which comes with: 1. Resin bottle, x1 2. Curing strips 3. Razor blade No affiliation. I chose it because it includes "long crack" in its product description and instructions. ## Steps 1. Mark the crack from inside. 2. From outside/above, apply resin VERY slowly along the crack. 3. Move at the speed for the crack line to disappear (not as visible). 4. Reapply resin wherever necessary. 5. Apply a small amount of pressure on the crack, from inside in the car. 1. just enough pressure 2. on both sides and center of crack 3. to help reduce air pockets 6. Cover the crack with curing strips. 7. Move the car outside, under the sun, and let it cure for 10 minutes or so. 1. Or you may use a curing light. 8. After it is cured, remove the curing strips. 9. Use the provided razor blade to scratch off cured resin on the glass surface. 1. Hold blade 90 degree (perpendicular to) the glass. 10. Check crack visually. ## Notes + It is a cloudy day and I leave the windshield under the sun/cloud for hours to cure. + Crack is much harder to see after the repair; but visible from a certain angle. + One month after the repair, the crack remains the same size (no growth). ## Question Not sure how long the repair will hold up, but will report back in a year or so. -- Be safe. Stay dirty. Enjoy the work! God bless!
# Honda V6 VCM Oil Pressure Switch Replacement (Code P3400) Honda V6 Engine J35A7, with VCM (Variable Cylinder Management) shown in the 2010 Odyssey Ex-L ## Reason * Check engine light P3400 * Valve Pause System (VPS) stuck in off position - bank 1 ## Supplies 1. Honda Oil Pressure Switch, part#: 37240-R70-A04 2. O-ring, part#: 91319-PAA-A01 ## Tools 1. Ratchet socket/box wrench 2. 24 mm deep socket 3. Torque wrench (set at 13 ft pounds) 4. Pick ## Preparation 1. Pop the hood 2. Remove the engine cover ## Oil Pressure Switch Removal 1. Find the bank 1 (in the back, to the firewall) oil pressure switch 2. Remove connector to the oil pressure switch 3. Use a 24mm deep socket to remove switch 4. Use a pick to remove the existing gasket, possibly stuck on the engine 5. Clean the surface ## Oil Pressure Switch Replacement 1. Lubricate the new o-ring with engine oil. 2. Put the new o-ring back on the engine contact. 3. Thread the oil pressure switch on, and make sure the o-ring is in place. 4. Torque the switch to 13 ft lb or snug. ## Check 1. Start engine and check leaks 2. Clear code and test drive ## Additional comments Some service manuals (on older models) suggest the use of liquid gasket on the thread. However, I don't see anything on the factory switch thread and skip this step. It is working fine and so far no leak on the Odyssey. -- Be safe, stay dirty. Enjoy the work! God bless!
# 2010 Honda Odyssey Ex-L Replacement of Taillight Assemblies (Tail Lights) ## Supply 1. Outer Tail Light Assembly 2. Inner Tail Light Assembly ## Tools 1. Panel removal tools 2. Ratchet wrench 3. 8mm socket 4. Swivel joint 5. Socket extension ## A. Taillight Outer Assembly Replacement 1. Remove 2 screws in the back. 2. Push the assembly toward the back to remove. * It is helpful to use a panel remove tool for leverage. 3. Remove connectors to the lights. 4. Remove lights, if you want to reuse them. 5. Reinstall lights in the new assemly, if you reuse them. 6. Plug light connectors back. 7. Align the follow when placing the new assembly: 1. Front: Align the push pin/clip on the assemly to the hole on the body. 2. Back: Align the 2 screw holes on the assembly to those on the back of the car. 8. Push the assembly forward (toward to the front) until it is in (front pin/clip engaged) 9. Tighten the 2 screws in the back, and put on the plastic covers. 10. DONE with the outer assembly. ## B. Taillight Inner Assembly Replacement 1. Lift the tailgate to access its back. 2. Open the plastic cover on the side for access to the light connectors. 3. Remove light connectors. 4. Remove 2 nuts with 8mm socket, with a swivel joint and extension if necessary. 5. Remove 2 cap nuts on the side, outside the cover/opening. 8mm again. 6. Lower the tailgate but do not close it. 7. Wiggle the inner assembly, pull it back while sliding it to the side to remove it. * It may help to pry the tailgate latch handle a bit. 8. Install lights in the new assembly, if it doesn't come with them. 9. Pry the tailgate latch/handle cover, and slide the new assembly in. 10. Make sure it is aligned on the tailgate, and push the assembly to engage its clips. 11. Tighten nuts on the inside and cap nuts on the outside. 12. Plug the light connectors. 13. DONE with the inner assembly. Start the car and test the lights. It is all DONE. Hope this video is informative. Be safe, stay dirty. Enjoy the work! God bless!
# 2010 Honda Odyssey EX-L Replacement of Front Brake Rotors and Pads ## Supply 1. Front brake rotor x2 2. Front brake pad x2 3. Brake lubricant / grease 4. Anti-seize paste 5. Brake cleaner 6. Thread locker (blue) 7. Optional: brake fluid 8. Optional: Penetrating oil, e.g. PB blaster or WD40 ## Tools 1. Breaker bar or ratchet wrench x1 2. 14mm, 19mm, 22mm sockets 3. Bungee cord x1 4. Torque wrench: 101 ft pounds 5. Caliper piston pressing tool (or a clamp) 6. Manual impact screw driver (recommended) 7. Wire brush 8. Optional: M8 x 1.25 bolt x2 ## 1. Safety and Preparation 1. Engage parking brake 2. Chocks 3. Pop the hood, take out some brake fluid 4. Loose the lug nuts (22 mm socket) 5. Raise the car, take off the nuts, and tires 6. Tires under car for additional protection 7. Safety check!!! ## 2. Rotor and Pad Removal 1. Remove brake calliper: bolts 14 mm x2, wrench to prevent spin 2. Hang calliper with bungee cord 3. Remove brake bracket: 19 mm bolts 4. Remove rotor: I. Impact screw driver to remove factory screws II. Run 8x1.25 bolts to separate the rotor ## 3. Rotor and Pad Installation 1. Wire brush / prep /clean the wheel bearing hub (remove rust for a clean surface) 2. Clean the rotor with brake cleaner 3. Align the set holes and put the factory screws back on 4. Wire brush / prep /clean the bracket 5. Install brake hardware (shims) 6. Regrease /lubricate the pins 7. Thread lock the bracket bolts (19mm) x2 8. Reinstall the bracket, and torque to 101 ft pounds 9. Grease the new pads: back, top, bottom 10. Install the new pads (slide in with an angle and rotate) 11. Note the brake with wear indicator is inside 12. Press the caliper piston: I. Make sure they are fully seated in the rubber boots II. Check brake fluid in the master cylinder (no overflow) 13. Clean and grease piston contact 14. Reinstall the caliper, with 14mm bolts thread-locked 15. Torque to 37 ft pounds ## 4. Finishing 1. Repeat the steps for the other side 2. Reinstall the wheels with lug nuts torqued to 94 ft pounds 3. Lower down the vehicle 4. Add brake fluid back to maximum 5. Pump brake pedals until it is firm ## 5. Breaking in Follow instructions on the rotors/pads for breaking in procedures. Hope this video is informative. Be safe, stay dirty. Enjoy the work! God bless!









