## Problem 2017 Lexus RX350 with the new classic Toyota V6 engine 2GR-FKS: + 83,000 miles + with the factory spark plugs Toyota recommends 60,000 miles interval for spark plug replacement. Have to replace them but will start with the plugs in the front, which are easier to remove. Will also see what the spark plugs look like after 6 years and more than 80 thousand miles. ## Procedure 1. Park your vehicle on a level surface and turn off the engine. 2. Open the hood and remove engine cover. 3. Disconnect the electrical connector from each ignition coil by pressing down on the release tab and pulling it away from the coil. 4. Remove the ignition coil by using a ratchet * 10mm socket to unscrew the bolts that hold it in place. * Pull the ignition oil from the tube. 5. Use a spark plug socket to remove the old spark plug from the cylinder head. Turn the socket counterclockwise to loosen and remove it. 6. Check the condition of the old spark plug. * Wet/oil on the threads of one plug; should monitor possible oil leak of tube o-ring. * Clean and no carbon deposit, gap still within spec. 7. Compare to the new plugs; they should have the same size and specs. 8. No anti-seize compound on the threads of the new spark plug. The new plugs are pre-gapped so no need to gap them. 9. Use the spark plug socket to thread the new spark plug into the cylinder head. Turn the socket clockwise until the spark plug is snug and seated properly. 10. Use a torque wrench to tighten the spark plug to the specified torque for your vehicle. For the 2GR-FKS engine, the torque specification for spark plugs is 13 lb-ft (18 Nm). 11. Repeat steps for each spark plug that needs to be replaced. We will replace the rear spark plugs in another video. 12. Reinstall the ignition coils by using the ratchet and socket to tighten the bolts that hold them in place. 13. Reconnect the electrical connectors to each ignition coil by pushing them into place until they click. 14. Start the engine to test the new spark plugs. 15. Reinstall engine cover, which makes the engine sound quieter. ## Notes Again, Toyota recommends 60,000 miles interval for spark plug replacement on this engine another latest models. Spark plugs are cheap so do not delay in their replacement (like me) as worn spark plugs can stress out other more expensive components of the engine such as ignition coils. Hope this is helpful. God bless!
It is a sealed transmission on a Toyota or Lexus. No dipstick on the transmission. Toyota says it is life-time transmission fluid?! Is it really life time? Do you replace the transmission fluid? Do you also replace the filter (strainer) inside the transmission oil pan? These are important questions for the life of your car.
Replace power steering fluid regularly, every 30,000 miles or 2-3 years. It is the hydraulic fluid that help you turn the wheel and a lubricant for the moving parts of your steering system, especially for the longevity of your steering pump and steering rack. #powersteering #carmaintenancetips
# Check engine light P0302. Spark plug or ignition coil pack? Diagnosis and fix. Or related code P0301, P0303, P0304, P0305, P0306, P0307, P0308. Vehicle: 2010 Honda Odyssey Ex-L Engine: Honda V6 J35A7 ## Problem Code: P0302 Cylinder 2 Misfire ## Analysis Most common causes: 1. Spark plug; OR 2. Ignition coil pack; ## Test 1. Take out the ignition coil pack from a GOOD cylinder, e.g. cylinder 4. 2. Take out the ignition coil pack from the BAD cylinder, i.e. cylinder 2. 3. Swap the two coil pack, that is: * Install coil pack \#2 to cylinder 4 * Install coil pack \#4 to cylinder 2 4. Clear code, start the engine, and scan engine. ## Result and Fix ### Scenario 1 IF the code changed to: "P0304 cylinder 4 misfires" meaning the GOOD cylinder is now bad with the new coil pack, replace the coil pack. ### Scenario 2 IF the code comes back with an unchanged misfire code: "P0302 cylinder 2 misfires" Then the coil is not the culprit, and it is most likely the spark plug in the BAD cylinder. Replace the spark plug: 1. With a spark plug socket, take out the old plug from the BAD cylinder, i.e. number 2. 2. Thread the new plug on with a small ratchet and fingers. 3. Torque to 13 ft-lb, or hand-tight. * No grease (anti-seize) * Do NOT over-tighten 4. Clear the code and have a test drive. 5. All done if code doesn't come back. ## Notes On spark plug replacement: 1. If it has been a while since last spark plug replacement, you may consider replace them ALL. 2. If one starts to go out, it's likely the others will do too. 3. Don't stretch it as it can lead to more costly repairs later. 4. Examples on spark plug replacement intervals: * Honda engines: no more than 100k miles * Toyota engines (old): no more than 120k miles * Toyota engines (latest): no more than 60k miles On other causes of misfire: 1. Bad fuel 2. Bad fuel injection 3. Engine lubrication, oil getting into combustion 4. Others Fix the problem ASAP as it can lead to more catastrophic problems on the engine and/or catalytic convertor, which are very costly. -- I hope this video is helpful and informative. Consider give us a like and subscribe! God bless!
# Why your steering wheel shakes (pulsation) when braking and fix it in 6.57 minutes Vehicle in the video: 2010 Honda Odyssey EX-L ## Concerns Steering wheel pulsation when you brake/slow down... especially on the highway. Possible causes: 1. Likely uneven wear of brake pads and/or warped brake rotors. 2. Front brakes and/or rear brakes. In the case of my 2010 Honda Odyssey, it was the rear brakes. ## Supply 1. Rear brake rotor x2 2. Rear brake pad x2 3. Brake lubricant / grease 4. Anti-seize paste 5. Brake cleaner 6. Thread locker (blue) 7. Optional: brake fluid 8. Optional: Penetrating oil, e.g. PB blaster or WD40 ## Tools 1. Breaker bar or ratchet wrench x1 2. 12 mm, 17mm, 22mm sockets 3. Bungee cord x1 4. Torque wrench: 65 and 16 ft pounds 5. Caliper piston pressing tool (or a clamp) 6. Manual impact screw driver (recommended) 7. Wire brush 8. Optional: M8 x 1.25 bolt x2 ## 1. Safety and Preparation 1. Engage parking brake first 2. Chocks 3. Pop the hood, take out some brake fluid 4. Loose the lug nuts (22 mm socket) 5. Raise the car, take off the nuts, and tires 6. Tires under car for additional protection 7. Safety check!!! ## 2. Rotor and Pad Removal 1. Remove brake calliper: bolts 12 mm x2 2. Hang calliper with bungee cord 3. Remove brake bracket: 17 mm bolts, it helps to use penetratig oil 4. With safety check and parking brake RELEASED, remove rotor: I. Impact screw driver to remove factory screws II. Run 8x1.25 bolts to separate the rotor ## 3. Rotor and Pad Installation 1. Wire brush / prep /clean the wheel bearing hub (remove rust for a clean surface) 2. Clean the rotor with brake cleaner 3. Align the set holes and put the factory screws back on 4. Wire brush / prep /clean the bracket 5. Install brake hardware (shims) 6. Regrease /lubricate the pins 7. Thread lock the bracket bolts (17mm) x2 8. Reinstall the bracket, and torque to 65 ft pounds 9. Grease the new pads: back, top, bottom 10. Install the new pads (slide in with an angle and rotate) 11. Note the brake with wear indicator is inside 12. Press the caliper piston: I. Make sure they are fully seated in the rubber boots II. Check brake fluid in the master cylinder (no overflow) 13. Clean and grease piston contact 14. Reinstall the caliper, with 12mm bolts thread-locked 15. Torque to 16 ft pounds ## 4. Finishing 1. Repeat the steps for the other side 2. Reinstall the wheels with lug nuts torqued to 94 ft pounds 3. Lower down the vehicle 4. Add brake fluid back to maximum 5. Pump brake pedals until it is firm ## 5. Breaking in Follow instructions on the rotors/pads for breaking in procedures. Hope this video is informative. Be safe, stay dirty. Enjoy the work! God bless!
# Honda Transmission Fluid Change Vehicle in video: 2010 Honda Odyssey EX-L ## Tools and Supply 1. 3/8'' rachet 2. OR, a 3/8'' breaker bar 2. 17 mm socket x1 4. Torque wrench (set at 29 and 36 ft pounds) 5. Honda ATF (DW-1), 3.3 quarts 6. Gaskets, for fill and drain plugs * Honda fill cap washer part #90441-PK4-000 (24mm) * Honda drain plug washer part #94109-20000 (I.D. 18mm) ## Safety and Preparation 1. Raise car 2. Pop hood 3. Chocks 4. Safety check!!! ## Fluid Change 1. Take off the fill cap with 17mm socket, long extension and perhaps a swivel 2. Put catch pan under transmission. 2. Take off the transmission drain plug with 3/8 ratchet or breaker bar. 3. Let it drain... 4. Clean the drain plug, shavings on the magnet. 5. Replace the drain plug with a new gasket, put it back after drained, and torque it to 36 ft-lb 6. With a long funnel, fill about 3.3 quarts of Honda DW-1 Transmission fluid. 7. Replace fill cap with a new washer, but don't tighten it yet. 8. Check fluid level on ground level, after vehicle reaches operating temperature, and engine OFF 9. Torque fill cap to 29 ft-lb ## Final Comments 1. Fluid change intervals * First change at 60,000 miles * Change every 30,000 miles afterwards 2. What fluid: best to use Honda fluid for that year & model 3. No flush; if you change it every 30k miles, that's good for the transmission. 4. Fluid color means little; it becomes dark once you put it in. -- Be safe, stay dirty. Enjoy the work! God bless!
# To Burn, or Not to Burn (Oil vs. Fuel), Honda Engine VCM Honda V6 Engine with VCM (Variable Cylinder Management) shown in the 2010 Odyssey Ex-L ## Problem * Honda V6 (J35A7) burns oil, at least 1 quart every 1500 miles ## Reason * VCM (Variable Cylinder Management) is the likely culprit * VCM shuts off some of the cylinders to consume LESS FUEL, which is good in this time of high gas prices * HOWEVER, it creates imbalances and vacuums in the engine with likely problems such as: 1. Engine and mount wear (and noise/failure over time) 2. OIL BURNING, bad for the engine, cat converter (costly), and the environment 3. It can ruin the engine if the oil level goes too low * You can disable VCM by adding a muzzler (resistor) to the coolant temperature sensor: * VCM is only turned on after the engine is WARMED up (at a certain coolant temperature) * Added resistor increases sensor OHM and signals a temperature below the desired condition for VCM, which will not get turned on ## Supplies 1. Honda VCM Muzzler / DIPressor 2. OR, if you can make a resistor of varying 82-100 ohm, that may work as well. Here is the one I purchased on eBay: https://www.ebay.com/itm/265031739235 ## Tools Optional: 1. An OBD II Scanner to clear code, in case it appears ## Steps 1. Engine OFF 2. Pop the hood 3. Remove the engine cover 4. Remove the coolant temperature sensor 5. Chain the muzzler with sensor: sensor harness to muzzler to sensor connector on the engine block 6. Start with the lower DIP or ohm setting, e.g. at 82 ohms. 7. Test the car to see if ECO mode appears in any driving condition. 8. Adjust/increase ohm if necessary and test drive again, until VCM no longer returns. Here are my DIP settings in Pennsylvania USA: 1. 82 ohms in the Winter 2. 92 ohms in the Summer ## Results 1. ECO never comes back with the above settings. 2. I no longer need to add oil between oil changes. -- Be safe, stay dirty. Enjoy the work! God bless!
# Tire Rotation for an AWD (X Pattern) X Rotation for an All-Wheel Drive ## Tools 1. Breaker bar or impact wrench 2. Torque wrench 3. Floor jack, x1 4. Jack stands, x4 ## Preparation Note if you use a breaker bar, you may have to loosen (NOT remove) lug nuts before raising the vehicle. 1. Raise the vehicle, both the front and the rear. 2. Support the vehicle with jack stands (4). ## Rotation Steps 1. Remove the right front, and move it to the left rear. 2. Remove the left rear, and install the tire from the right front & secure lug nuts. 3. Remove the left front, and move it to the right rear. 4. Remove the right rear, and install the tire from the left front & secure lug nuts. 5. Lower the rear of the vehicle, and tighten the rear lug nuts to torque spec. 6. Install tire from right rear to left front, and secure with lug nuts. 7. Install tire from left rear to right front, and secure with lug nuts. 8. Lower the front of the vehicle and torque front lug nuts to spec. 9. Double-check torques. 10. Done. ## Notes * I rotate the tires every 5000 miles or so. * This procedure is for non-directional tires. This cannot be done on directional tires such as some winter tires. -- Be safe, stay dirty. Enjoy the work! God bless!
Replacement of Rear Brake Pads on a 2017 Lexus RX350 AWD Base model ## Supplies 1. Rear brake pads: 2x2 for both sides 2. Brake hardware & lubricant/grease 3. Brake cleaner 4. Thread locker (blue) ## Tools 1. Breaker bar or ratchet wrench x1 2. 14mm and 21mm sockets, and preferably a 17 mm box wrench 3. Bungee cord x1 4. Torque wrench: 25 and 76 ft pounds 5. Syringe or turkey baster 6. 12 volt DC plus small test leads ## 1. Safety and Preparation 1. Loosen (but not remove) lug nuts on the rear wheels, with a 21 mm socket. 2. Jack up the car (rear) and support it with jack stands. 3. Make sure the support is stable. Safety check! 4. Pop the hood, and take out some brake fluid. 5. Remove the lug nuts, and remove the wheels. 6. Put wheels under the car for additional protection. ## 2. Brake Caliper Removal 1. Remove two mounting bolts (14 mm), with: 1. with a 17 mm box wrench to hold the pin in place 2. and ratchet with 14mm socket to loosen the bolt 2. Remove the connector from the electric parking brake (EPB) motor. 3. You may slide the pins (top and bottom) out to remove them. 4. Remove and secure the caliper with a bungee cord. ## 2. Disengage Electric Parking Brake (in Service Mode) With a 12 volt DC power: 1. Put the brake pressing tool on the caliper, lightly touching the piston. 2. Connect battery negative (with a small test lead/clamp) to one pin on the EPB motor. 3. Connect/touch the positive lead to the other pin on the EPB motor, and you should hear the motor running sound. 4. Observe if the piston is pushing out (to tighten the pressing tool) or withdrawing (to loosen the pressing tool). 5. Once you know the correct connection to retract, repeat the following steps: 1. Activate the motor to retract; 2. Compress the piston; 6. Repeat the above until the piston is flush with the caliper surface. 7. The caliper/piston is ready to be reinstalled with new pads. For other methods to put EPB in the service mode, you can watch this video: https://www.youtube.com/watch?v=XgaRKr3BRvI ## 4. Brake Pad Replacement 1. Clean and grease /lubricate the pins. 2. Slide them back into the caliper bracket, boots on. 3. Remove the old pads, and pry off the existing hardware. 4. Apply a bit of grease on new hardware (on the pad touching contact), and install them. 5. Install the wear indicator hardware on the pad. 6. Slide the pad in an angel, turn, and push it in. 7. Apply some grease on the back/shim of the pad. 8. Replace the inside pad in the like manner. The same procedure but it is difficult to see and takes some patience. :) 9. Put the brake caliper back on the pads. 10. Apply blue thread locker on the mounting bolts. 11. Tighten the bolts (14 mm x2) to 25 ft-lb. ## 5. Finishing 1. Repeat the steps for the other side 2. Reinstall the wheels with lug nuts 3. Lower down the vehicle 4. Torque lug nuts to 76 ft pounds. 5. Check brake fluid level. 6. Start the car and pump the brake pedal several times. ## 5. Breaking in Follow instructions on the pads for breaking-in procedures, if necessary. -- Hope this video helps. Be safe, stay dirty. Enjoy the work! God bless!
# Toyota Lexus Rear Brakes with EPB: 3 Methods to Enter the Service Mode Rear brake service on a 2017 Lexus RX350 AWD Base model ## Tools These are options: 1. Bidirectional scan tool, OR 2. If you have a recent Toyota/Lexus models that supports a simple procedure, OR 3. 12 V DC battery ## Safety and Preparation Follow all safety precautions to any job on a vehicle. ## Method 1: Use a Bidirectional Scan Tool On a XTool, for example: 1. Connect the OBD scan tool. 2. Start the car. 3. On XTool, select Special function / EPB / ASIA / Lexus / Automatic selection. 4. Select Enter Maintenance Mode, and confirm. 5. You should hear a whining sound to disengage the parking brake. 6. Parking light will be flashing slowly. 7. Now the vehicle is in the service mode. To exit service mode after service is done: 1. Select Exit Maintenance Mode, and confirm. 2. You should hear a whining sound to reengage the parking brake. 3. Parking light will turn solid. 4. Now the vehicle is back to normal operations. ## Method 2: The Toyota / Lexus Procedures This may or may not work on your vehicle so research your year/model to find out. It doesn't work on my 2017 Lexus RX350, but on later models after 2019. Disengage Electric Parking Brake (in Service Mode): 1. Without pressing the brake pedal, start the car once. 2. While depressing the brake pedal, within 8 seconds: 1. Pull (up) the (P) lever 3 times; 2. Push (down) the (P) lever 3 times; 3. While foot OFF brake, push and hold (P) unless the (P) indicator on dash is flashing SLOWLY. * You may be able to hear the rear brake's electric rotor is running to retract the piston. 4. Release the (P) lever, and it is now in the Service mode. 5. Press Start/Stop to turn off ignition. Re-Engage Electric Parking Brake (cancel Service Mode): 1. Without pressing the brake pedal, start the car once. 2. While foot off brake, pull and hold (P) lever until the (P) light is out. * You may be able to hear the rear brake's eletric rotor sound again. 3. Release the (P) lever, and it is now back to normal (with eletric parking brake) 4. Press Start/Stop to turn off ignition. ## Method 3: Use a 12V DC Power After the removal of the connector to the brake piston motor on the caliper: 1. Put a brake pressing tool on the brake piston, loosely engaged. 2. Connect one wire (e.g. black/negative) of the 12V DC to one pin on the motor. 3. Contact the other wire (e.g. red/positive) of the 12VDC with the other pin on the motor. 4. The motor will run and whine when the power is provided. 5. Make sure the motor is retracting the piston: 1. If it runs and compresses the pressing tool (making it tighter), reverse the two wire/connectors. 2. Only run the motor very briefly, and try to compress the piston with the pressing tool. 3. You can easily press piston with the tool if the motor is retracting in the right direction. 4. Do not force. 6. Once it is full retracted, you compress the piston to flush. ## Brake Job Afterwards If one of the methods works, you can then proceed with the rear brake job. -- Be safe, stay dirty. Enjoy the work! God bless!
# Lexus Oil Change 2017 Lexus RX350 Base AWD Engine: Toyota 3.5L V6 2GR-FKS ## Supply 1. Oil: 0W20 x5.8 qt 2. Oil Filter: 04152-YZZA1 1 $4.21 Oil filter cap torque 18 ft-lb 3. Drain gasket: 90430-12031 1 $0.88 Drain plug torque 30 ft-lb 4. Disposable gloves ## Tools 1. Ratchet socket wrench or breaker bar x1 2. 14 mm socket (or box wrench) 3. Oil filter wrench for Toyota/Lexus 4. Torque wrench (18 and 30 ft-lb) ## Safety and Preparation 1. Engage parking brake 2. Chocks 3. Pop the hood 4. Raise the car: using floor jack + jack stands or ramps 5. Safety check!!! ## Oil Change 1. Tip: Warm up the engine, 5 minutes 2. Open the oil cap, read the oil grade (0w20), or owner's manual 3. Remove the drain plug (14mm socket), and drain oil 4. Remove oil filter, with a filter wrench 5. Replace oil filter, and make sure: 1. clean 2. lubricate the rubber o-ring with oil 3. check cap on the filter, finger tight 4. torque oil filter to 18 ft-lb 6. Replace drain plug with new crush washer, clean, and torque to 30 ft pounds 1. Make sure to remove any remnant of gasket on the drain pan or bolt 7. With a funnel, add 5+ gallons, check it, and add more if necessary 1. check owner's manual, OR 2. measure the amount you take out 8. Start the engine, check leaks, shut off and measure with dipstick 9. For accurate oil level measurement, make sure your car is level * you can lower the car at this point 11. Make sure no leak near oil filter and drain plug ## Oil Reset 1. Menu / Settings 2. Vehicle settings 3. Services/Maintenance / Reset Oil Change 4. Edit and set 5000 miles for the next service ## Final Comments 1. Oil change interval: 5000 miles or 6 months, whichever comes first 2. Oil type: Synthetic 0w20 3. Oil brand: doesn't matter as long as it is 0w20 (check your owner's manual) 4. Recycle the used oil Be safe, stay dirty. Enjoy the work! God bless!
# 2010 Honda Odyssey EX-L Replacement of Front Brake Rotors and Pads ## Supply 1. Front brake rotor x2 2. Front brake pad x2 3. Brake lubricant / grease 4. Anti-seize paste 5. Brake cleaner 6. Thread locker (blue) 7. Optional: brake fluid 8. Optional: Penetrating oil, e.g. PB blaster or WD40 ## Tools 1. Breaker bar or ratchet wrench x1 2. 14mm, 19mm, 22mm sockets 3. Bungee cord x1 4. Torque wrench: 101 ft pounds 5. Caliper piston pressing tool (or a clamp) 6. Manual impact screw driver (recommended) 7. Wire brush 8. Optional: M8 x 1.25 bolt x2 ## 1. Safety and Preparation 1. Engage parking brake 2. Chocks 3. Pop the hood, take out some brake fluid 4. Loose the lug nuts (22 mm socket) 5. Raise the car, take off the nuts, and tires 6. Tires under car for additional protection 7. Safety check!!! ## 2. Rotor and Pad Removal 1. Remove brake calliper: bolts 14 mm x2, wrench to prevent spin 2. Hang calliper with bungee cord 3. Remove brake bracket: 19 mm bolts 4. Remove rotor: I. Impact screw driver to remove factory screws II. Run 8x1.25 bolts to separate the rotor ## 3. Rotor and Pad Installation 1. Wire brush / prep /clean the wheel bearing hub (remove rust for a clean surface) 2. Clean the rotor with brake cleaner 3. Align the set holes and put the factory screws back on 4. Wire brush / prep /clean the bracket 5. Install brake hardware (shims) 6. Regrease /lubricate the pins 7. Thread lock the bracket bolts (19mm) x2 8. Reinstall the bracket, and torque to 101 ft pounds 9. Grease the new pads: back, top, bottom 10. Install the new pads (slide in with an angle and rotate) 11. Note the brake with wear indicator is inside 12. Press the caliper piston: I. Make sure they are fully seated in the rubber boots II. Check brake fluid in the master cylinder (no overflow) 13. Clean and grease piston contact 14. Reinstall the caliper, with 14mm bolts thread-locked 15. Torque to 37 ft pounds ## 4. Finishing 1. Repeat the steps for the other side 2. Reinstall the wheels with lug nuts torqued to 94 ft pounds 3. Lower down the vehicle 4. Add brake fluid back to maximum 5. Pump brake pedals until it is firm ## 5. Breaking in Follow instructions on the rotors/pads for breaking in procedures. Hope this video is informative. Be safe, stay dirty. Enjoy the work! God bless!












