# Check engine light P0302. Spark plug or ignition coil pack? Diagnosis and fix. Or related code P0301, P0303, P0304, P0305, P0306, P0307, P0308. Vehicle: 2010 Honda Odyssey Ex-L Engine: Honda V6 J35A7 ## Problem Code: P0302 Cylinder 2 Misfire ## Analysis Most common causes: 1. Spark plug; OR 2. Ignition coil pack; ## Test 1. Take out the ignition coil pack from a GOOD cylinder, e.g. cylinder 4. 2. Take out the ignition coil pack from the BAD cylinder, i.e. cylinder 2. 3. Swap the two coil pack, that is: * Install coil pack \#2 to cylinder 4 * Install coil pack \#4 to cylinder 2 4. Clear code, start the engine, and scan engine. ## Result and Fix ### Scenario 1 IF the code changed to: "P0304 cylinder 4 misfires" meaning the GOOD cylinder is now bad with the new coil pack, replace the coil pack. ### Scenario 2 IF the code comes back with an unchanged misfire code: "P0302 cylinder 2 misfires" Then the coil is not the culprit, and it is most likely the spark plug in the BAD cylinder. Replace the spark plug: 1. With a spark plug socket, take out the old plug from the BAD cylinder, i.e. number 2. 2. Thread the new plug on with a small ratchet and fingers. 3. Torque to 13 ft-lb, or hand-tight. * No grease (anti-seize) * Do NOT over-tighten 4. Clear the code and have a test drive. 5. All done if code doesn't come back. ## Notes On spark plug replacement: 1. If it has been a while since last spark plug replacement, you may consider replace them ALL. 2. If one starts to go out, it's likely the others will do too. 3. Don't stretch it as it can lead to more costly repairs later. 4. Examples on spark plug replacement intervals: * Honda engines: no more than 100k miles * Toyota engines (old): no more than 120k miles * Toyota engines (latest): no more than 60k miles On other causes of misfire: 1. Bad fuel 2. Bad fuel injection 3. Engine lubrication, oil getting into combustion 4. Others Fix the problem ASAP as it can lead to more catastrophic problems on the engine and/or catalytic convertor, which are very costly. -- I hope this video is helpful and informative. Consider give us a like and subscribe! God bless!
# Why your steering wheel shakes (pulsation) when braking and fix it in 6.57 minutes Vehicle in the video: 2010 Honda Odyssey EX-L ## Concerns Steering wheel pulsation when you brake/slow down... especially on the highway. Possible causes: 1. Likely uneven wear of brake pads and/or warped brake rotors. 2. Front brakes and/or rear brakes. In the case of my 2010 Honda Odyssey, it was the rear brakes. ## Supply 1. Rear brake rotor x2 2. Rear brake pad x2 3. Brake lubricant / grease 4. Anti-seize paste 5. Brake cleaner 6. Thread locker (blue) 7. Optional: brake fluid 8. Optional: Penetrating oil, e.g. PB blaster or WD40 ## Tools 1. Breaker bar or ratchet wrench x1 2. 12 mm, 17mm, 22mm sockets 3. Bungee cord x1 4. Torque wrench: 65 and 16 ft pounds 5. Caliper piston pressing tool (or a clamp) 6. Manual impact screw driver (recommended) 7. Wire brush 8. Optional: M8 x 1.25 bolt x2 ## 1. Safety and Preparation 1. Engage parking brake first 2. Chocks 3. Pop the hood, take out some brake fluid 4. Loose the lug nuts (22 mm socket) 5. Raise the car, take off the nuts, and tires 6. Tires under car for additional protection 7. Safety check!!! ## 2. Rotor and Pad Removal 1. Remove brake calliper: bolts 12 mm x2 2. Hang calliper with bungee cord 3. Remove brake bracket: 17 mm bolts, it helps to use penetratig oil 4. With safety check and parking brake RELEASED, remove rotor: I. Impact screw driver to remove factory screws II. Run 8x1.25 bolts to separate the rotor ## 3. Rotor and Pad Installation 1. Wire brush / prep /clean the wheel bearing hub (remove rust for a clean surface) 2. Clean the rotor with brake cleaner 3. Align the set holes and put the factory screws back on 4. Wire brush / prep /clean the bracket 5. Install brake hardware (shims) 6. Regrease /lubricate the pins 7. Thread lock the bracket bolts (17mm) x2 8. Reinstall the bracket, and torque to 65 ft pounds 9. Grease the new pads: back, top, bottom 10. Install the new pads (slide in with an angle and rotate) 11. Note the brake with wear indicator is inside 12. Press the caliper piston: I. Make sure they are fully seated in the rubber boots II. Check brake fluid in the master cylinder (no overflow) 13. Clean and grease piston contact 14. Reinstall the caliper, with 12mm bolts thread-locked 15. Torque to 16 ft pounds ## 4. Finishing 1. Repeat the steps for the other side 2. Reinstall the wheels with lug nuts torqued to 94 ft pounds 3. Lower down the vehicle 4. Add brake fluid back to maximum 5. Pump brake pedals until it is firm ## 5. Breaking in Follow instructions on the rotors/pads for breaking in procedures. Hope this video is informative. Be safe, stay dirty. Enjoy the work! God bless!
# Easy Removal of Paint Transfer / Scuffs on Your Car ## Reason * I have multiple paint scuffs on the beautiful Lexus RX350. Some of these look terrible (see what happened at the end). * Fortunately, they are very easy to remove and you only need very basic supplies. ## Paint Transfer or Scratch? How do you know it is paint transfer and not a (deep) scratch? 1. Paint transfer is a different color of paint on top of your car's paint/clear coat. 2. You can feel the "bump" when rubbing your finger on it. 3. Or, if you rub it with a wet finger, it may come off a bit. ## Tools or Supplies * [ ] Microfiber towels * [ ] WD40 * [ ] Mr. Clean MagicEraser (Durafoam) * [ ] Polishing Compound * [ ] Optional: Rubbing Compound ## Steps 1. [ ] Park your car in garage, under the shade, or do this on a cloudy day (NO Direct Sunlight) 2. [ ] Clean the surface with water (and soapy water if necessary) * [ ] Make sure there is NO Dirt * [ ] Clean, rinse, and wipe off with microfiber towels 3. [ ] Spray WD40 on the transferred paint * [ ] Let it soak for a minute if possible, and repeat the spray * [ ] WD40 will soften the paint and lubricate the removal/rubbing process 4. [ ] Lightly rub the paint with Mr. Clean MagicEraser foam * [ ] Follow the direction of the scuff * [ ] Check your foam and make sure you only remove the transferred paint, NOT the paint of your car 5. [ ] Wipe off, spray WD40 again, and repeat the process until the paint transfer is removed. 6. [ ] Clean the surface, and polish it with some polishing compound on microfiber towel * [ ] You may start with the rubbing compound first, before applying the polishing compound * [ ] Use a circular motion to apply the compound, with light/moderate hand pressure ## What Happened and Caused the Paint Transfer? 1. Other cars rubbed/"scratched" your car in the parking lot, and left their paint on it. 2. What happened to the big scuffs on my Lexus: Wife was at traffic lights when someone cut her off and rubbed the side of the car. That person did not have the courage to stop, and he ran away. My wife felt very upset with the terrible marks (thinking it were damages to the Lexus body paint) and couldn't believe it after I removed the scuffs 15 minutes later. -- Be safe. Enjoy the work! God bless!
# Windshield Long Crack Repair ## Purpose With a 6-inch long crack on the windshield, hope the repair will: 1. make it less visible; 2. stop the growth of the crack; ## Supply * RainX Windshield Repair Kit (resin bottle) https://www.rainx.com/product/rain-x-windshield-repair-kit/ which comes with: 1. Resin bottle, x1 2. Curing strips 3. Razor blade No affiliation. I chose it because it includes "long crack" in its product description and instructions. ## Steps 1. Mark the crack from inside. 2. From outside/above, apply resin VERY slowly along the crack. 3. Move at the speed for the crack line to disappear (not as visible). 4. Reapply resin wherever necessary. 5. Apply a small amount of pressure on the crack, from inside in the car. 1. just enough pressure 2. on both sides and center of crack 3. to help reduce air pockets 6. Cover the crack with curing strips. 7. Move the car outside, under the sun, and let it cure for 10 minutes or so. 1. Or you may use a curing light. 8. After it is cured, remove the curing strips. 9. Use the provided razor blade to scratch off cured resin on the glass surface. 1. Hold blade 90 degree (perpendicular to) the glass. 10. Check crack visually. ## Notes + It is a cloudy day and I leave the windshield under the sun/cloud for hours to cure. + Crack is much harder to see after the repair; but visible from a certain angle. + One month after the repair, the crack remains the same size (no growth). ## Question Not sure how long the repair will hold up, but will report back in a year or so. -- Be safe. Stay dirty. Enjoy the work! God bless!
# Honda V6 VCM Oil Pressure Switch Replacement (Code P3400) Honda V6 Engine J35A7, with VCM (Variable Cylinder Management) shown in the 2010 Odyssey Ex-L ## Reason * Check engine light P3400 * Valve Pause System (VPS) stuck in off position - bank 1 ## Supplies 1. Honda Oil Pressure Switch, part#: 37240-R70-A04 2. O-ring, part#: 91319-PAA-A01 ## Tools 1. Ratchet socket/box wrench 2. 24 mm deep socket 3. Torque wrench (set at 13 ft pounds) 4. Pick ## Preparation 1. Pop the hood 2. Remove the engine cover ## Oil Pressure Switch Removal 1. Find the bank 1 (in the back, to the firewall) oil pressure switch 2. Remove connector to the oil pressure switch 3. Use a 24mm deep socket to remove switch 4. Use a pick to remove the existing gasket, possibly stuck on the engine 5. Clean the surface ## Oil Pressure Switch Replacement 1. Lubricate the new o-ring with engine oil. 2. Put the new o-ring back on the engine contact. 3. Thread the oil pressure switch on, and make sure the o-ring is in place. 4. Torque the switch to 13 ft lb or snug. ## Check 1. Start engine and check leaks 2. Clear code and test drive ## Additional comments Some service manuals (on older models) suggest the use of liquid gasket on the thread. However, I don't see anything on the factory switch thread and skip this step. It is working fine and so far no leak on the Odyssey. -- Be safe, stay dirty. Enjoy the work! God bless!
# 2010 Honda Odyssey Ex-L Replacement of Taillight Assemblies (Tail Lights) ## Supply 1. Outer Tail Light Assembly 2. Inner Tail Light Assembly ## Tools 1. Panel removal tools 2. Ratchet wrench 3. 8mm socket 4. Swivel joint 5. Socket extension ## A. Taillight Outer Assembly Replacement 1. Remove 2 screws in the back. 2. Push the assembly toward the back to remove. * It is helpful to use a panel remove tool for leverage. 3. Remove connectors to the lights. 4. Remove lights, if you want to reuse them. 5. Reinstall lights in the new assemly, if you reuse them. 6. Plug light connectors back. 7. Align the follow when placing the new assembly: 1. Front: Align the push pin/clip on the assemly to the hole on the body. 2. Back: Align the 2 screw holes on the assembly to those on the back of the car. 8. Push the assembly forward (toward to the front) until it is in (front pin/clip engaged) 9. Tighten the 2 screws in the back, and put on the plastic covers. 10. DONE with the outer assembly. ## B. Taillight Inner Assembly Replacement 1. Lift the tailgate to access its back. 2. Open the plastic cover on the side for access to the light connectors. 3. Remove light connectors. 4. Remove 2 nuts with 8mm socket, with a swivel joint and extension if necessary. 5. Remove 2 cap nuts on the side, outside the cover/opening. 8mm again. 6. Lower the tailgate but do not close it. 7. Wiggle the inner assembly, pull it back while sliding it to the side to remove it. * It may help to pry the tailgate latch handle a bit. 8. Install lights in the new assembly, if it doesn't come with them. 9. Pry the tailgate latch/handle cover, and slide the new assembly in. 10. Make sure it is aligned on the tailgate, and push the assembly to engage its clips. 11. Tighten nuts on the inside and cap nuts on the outside. 12. Plug the light connectors. 13. DONE with the inner assembly. Start the car and test the lights. It is all DONE. Hope this video is informative. Be safe, stay dirty. Enjoy the work! God bless!






